Korg KORG Pa50 user manual 189, EG Attack, d EG Decay, Stereo Phaser, Resonance, h Wet/Dry

The “Src” parameter selects the source that starts the envelope generator. If you select, for example, Gate, the envelope generator will start when the note-on message is received.

When “Sweep Mode” = D-mod, the modulation source can control the flanger directly. Select the modulation source using the “Src” parameter.

The effect is off when a value for the modulation source speci- fied for the “Src” parameter is smaller than 64, and the effect is on when the value is 64 or higher. The Envelope Generator is triggered when the value changes from 63 or smaller to 64 or higher.

d: EG Attack, d: EG Decay

Attack and Decay speed are the only adjustable parame- ters on this EG.

023: Phaser

(Stereo Phaser)

This effect creates a swell by shifting the phase. It is very effective on electric piano sounds. You can add spread to the sound by offsetting the phase of the left and right LFOs from each other.

Stereo In - Stereo Out
Left	Wet / Dry
	Phaser
	Resonance
	High Damp
	Phaser
Right	Wet / Dry
	LFO Phase
LFO: Tri / Sine	LFO Shape

	LFO Waveform		Triangle, Sine
a	Selects LFO Waveform
	LFO Shape		–100...+100
	Determines how much the LFO waveform is changed		☞ Fx:020
b	LFO Phase [degree]		–180...+180
	Sets the LFO phase difference between the left and right		☞ Fx:010
	LFO Frequency [Hz]	0.02...20.00Hz
	Sets the LFO speed	☞ Fx:009,
c	Src			Off...Tempo
	Selects the modulation source of LFO speed
	Amt	–20.00...+20.00Hz
	Sets the modulation amount of LFO speed

		Effects					189
		Pitch/Phase Mod.
	BPM/MIDI Sync				Off, On
	Switches between using the frequency of the LFO speed and using the
	tempo and notes	☞ Fx:009,
	BPM		MIDI, 40...240
d	Selects MIDI Clock and assigns tempo			☞ Fx:009
	Base Note			☞ Fx:009
	Selects the type of notes that specify the LFO speed
	Times			x1...x16
	Sets the number of notes that specify the LFO speed			☞ Fx:009
e	Manual						0...100
	Sets the frequency to which the effect is applied
	Depth						0...100
	Sets the depth of LFO modulation
f	Src			Off...Tempo
	Selects the modulation source for the LFO modulation depth
	Amt			–100...+100
	Sets the modulation amount of the LFO modulation depth
	Resonance				–100...+100
g	Sets the resonance amount							☞
	High Damp [%]		0...100%
	Sets the resonance damping amount in the high range					☞
	Wet/Dry	–Wet...–1:99, Dry, 1:99...Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
		☞ Fx:010,
h	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt				–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

g: Resonance, h: Wet/Dry

The peak shape of the positive and negative Feedback value is different. The harmonics will be emphasized when the effect sound is mixed with the dry sound, if you set a positive value for both “Resonance” and “Wet/Dry”, and if you set a negative value for both “Resonance” and “Wet/Dry”.

g: High Damp [%]

This parameter sets the amount of damping of the reso- nance in the high range. Increasing the value will cut high-range harmonics.