Korg KORG Pa50 user manual Gate, 006 OD/HGainWah

178Effects

Filter/Dynamic

005: Gate

(Stereo Gate)

This effect mutes the input signal if its level is lower than the specified level. It also reverses the on and off operation of the gate, and uses Note On and Off messages to turn the gate on and off.

The Attack and Release parameters set the Gate attack time and release time.

Gate - Threshold

Output Level

Threshold

Louder

Stereo In - Stereo Out

Left

+

Envelope Select

Right

Gate+Sus

Delay

Envelope - Control

Envelope - Control

Delay

Wet / Dry

Gate

Gate

Wet / Dry

Louder

Input Level

Gate - Attack / Release

Threshold

Dry
Wet	Attack=1
	Release=1

	Envelope Select	D-mod, L/R Mix, L Only, R Only
	Selects from Control via the modulation source, mixing the left and right sig-
a	nals, Only left, and Only right			☞ ,
	Src		Off...Gate2+Dmpr
	Selects the modulation source that controls the gate when Envelope Select =
	D-mod
b	Polarity					+, –
	Switches between non-reversed and reversed Gate on/off					☞
c	Threshold				0...100
	Sets the level to which the Gate is applied						☞
	Attack				1...100
d	Sets the attack time						☞
	Release				1...100
	Sets the release time						☞
e	Delay Time [msec]					0...100msec
	Sets the delay time of the gate input						☞
	Wet/Dry		Dry, 1:99...99:1, Wet
	Table , “Sets the balance between the effect and dry sounds,” on page 175
f	Src			Off...Tempo
	Table , “Selects the modulation source of the effect balance,” on page 175
	Amt					–100...+100
	Table , “Sets the modulation amount of the effect bal-
	ance,” on page 175

a: Envelope Select, a: Src

The “Envelope Select” parameter selects whether the gate on/off is triggered by the level of the input signal, or controlled directly by the modulation source. The Src parameter specifies the modulation source, selected from Off to Gate2+Dpmr.

With “Envelope Select” = L/R Mix, the left and right chan- nel signal mixture will trigger the gate on/off. When L Only or R Only is selected, the gate is controlled by either of the channel signals.

b: Polarity

This parameter reverses the Gate on/off operation. With a negative value, the gate is closed when the input signal level exceeds the Threshold. The gate operation con- trolled by the modulation source is also reversed.

c: Threshold, d: Attack, d: Release

This parameter sets the signal level below which Gate is applied when “Envelope Select” is set to L/R Mix, L Only, or R Only.

Wet	Attack=100
	Release=100
Attack	Release

e: Delay Time

This parameter sets the delay time of the Gate input. If the sound has a very fast attack, increase the delay time so that the signal will be input after the Gate is opened. This will preserve the attack part of the sound.

006: OD/HGainWah

(Overdrive/Hi.Gain Wah)

This distortion effect utilizes an Overdrive mode and a Hi- Gain mode. Controlling the wah effect, the 3-band EQ, and the amp simulation will allow you to create versatile distor- tion sounds. This effect is suitable for guitar and organ sounds.

Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left			Wet / Dry
		Mode: Overdrive / Hi-Gain
Pre Low-cut		Drive
		3 Band PEQ
+	Wah	Driver	Amp Simulation
		Output Level
		Direct Mix
Right			Wet / Dry
D-mod

	Wah			Off, On
	Switches Wah on/off			☞ ,
	Src			Off...Tempo
a	Selects the modulation source that switches the Wah on and off
	Sw		Toggle, Moment
	Selects the switching mode for the modulation source that switches the Wah
	on and off			☞
	Wah Sweep Range			–10...+10
b	Sets the range of Wah			☞ ,
	Wah Sweep Src			Off...Tempo
	Selects the modulation source that controls the Wah			☞
c	Drive Mode	Overdrive, Hi-Gain
	Switches between overdrive and hi-gain distortion
	Drive			1...100
d	Sets the degree of distortion				☞
	Pre Low-cut		0...10
	Sets the low range cut amount of the distortion input			☞
	Output Level			0...50
	Sets the output level			☞ ,
e	Src			Off...Tempo
	Selects the modulation source for the output level
	Amt			–50...+50
	Sets the modulation amount of the output level