Return to Section TOC Return to Master TOC

Return to Section TOC Return to Master TOC

Return to Section TOC Return to Master TOC

Return to Section TOC Return to Master TOC

B-6

OPERATION FOR CODES ABOVE 11000 ONLY

B-6

7 MENU BUTTON AND DISPLAY SWITCH (Codes

TIG Mode Menu (with Advanced Control Panel installed):

above 11000) – Pressing and holding the (Menu)

 

Setting:

Description:

 

Button for about 5 seconds enters the menu display

Selection 4:

HS (TIG Hot Start % of output setting)

 

which allows:

 

 

0 *

+0%

(Only setting for SS0, above.)

 

Selection of up to seven programmable parameters

 

1

+10%

 

 

 

2

+20%

 

 

 

(Preflow, Upslope, Hot Start, Arc Force, etc.) on the

 

4

+40%

 

 

 

digital meter is achieved by momentarily pressing

 

3

+30%

 

 

 

 

5

+50%

 

 

 

and releasing the MENU button to step through the

 

6

+60%

 

 

 

parameters.

 

 

7

+70%

 

 

Setting of the desired level, displayed on the digital

 

8

+80%

 

 

 

9

+90%

 

 

 

meter for the selected parameter, is done by press-

Selection 5:

UP (Upslope Time)

 

 

ing the DISPLAY (momentary) switch toggle to the

 

0

None

(Only setting for SS1 & SS2, above.)

 

right to increase the level setting, or to the left to

 

1*

0.5 sec.

 

 

 

decrease it.

 

 

3

1.5 sec.

 

 

 

 

 

 

 

2

1.0 sec.

 

 

 

 

DIGITAL DISPLAY

 

4

2.0 sec.

 

 

 

 

*

5

2.5 sec.

 

 

 

 

 

 

Default Factory Setting. (Indicated by "blinking" decimal point.)

 

 

(SELECT)

DISPLAY

STICK Mode Menu (with Advanced Control Panel installed ):

 

 

(SET)

 

Setting:

Description:

 

 

 

DISPLAY

 

 

 

 

 

 

 

Selection 6:

HS (Stick Hot Start % added to output setting)

 

 

 

 

 

0

+0%

 

 

 

 

 

 

 

1

+10%

 

 

 

 

TIG Mode Menu

 

 

2

+20%

 

 

Setting:

 

 

3

+30%

 

 

Description:

 

 

4

+40%

 

 

Selection 1:

HF (High Freq.)

 

 

5 *

+50%

 

 

 

0

Scratch start TIG (No Hi-Freq.)

 

6

+60%

 

 

 

1 *

Normal Hi-Freq. start and weld

 

7

+70%

 

 

 

2

Lift TIG (Touch start w/o Hi-Freq.)

 

8

+80%

 

 

Selection 2:

PF (Preflow time)

 

 

9

+90%

 

 

 

0

No Preflow

 

Selection 7:

AF (Stick Arc Force % added to output setting)

 

1

0.1 sec.

 

 

0

+0%

("Softer" arc)

 

 

2 *

0.5 sec.

 

 

1 *

+10%

 

 

 

3

1.0 sec.

 

 

2

+20%

 

 

 

4

1.5 sec.

 

 

3

+30%

 

 

 

5

2.0 sec.

 

 

4

+40%

 

 

Selection 3:

SS (MicroStart™ Start Pulse)

 

5

+50%

 

 

 

0 *

No AC pulse/Low DC pulse (soft start)

 

6

+60%

 

 

 

1

High AC/DC pulse (forceful start)

 

7

+70%

 

 

 

2

HS setting (see below) for each pulse when Pulse

 

8

+80%

("Crisper" arc)

 

*

mode welding anodized aluminum.

*

9

+90%

 

Default Factory Setting. (Indicated by "blinking" decimal point.)

Default Factory Setting. (Indicated by "blinking" decimal point.)

Only selectable with Advanced Control Panel installed.

If no Advanced Control Panel the Stick menu

 

 

• Any of the following actions will exit the menu display:

displays “- - -“.

 

 

 

 

1. Pressing and holding the (Menu) Button again for about 5 seconds.

 

 

 

2. Allowing the menu display to be unchanged for about 15 seconds.

 

3. Closing the arc start switch (TIG Mode) or starting the arc (Stick Mode). Note: In Stick Mode the machine output will remain on while in menu display.

Re-entering.the menu displays the last parameter and setting that was displayed when the menu was exited

• All settings may be reset to the Factory Default Settings (above) by holding the (Menu) button pressed while turning on the machineʼs Power switch. The display will show “rES” to indicate the defaults are reset.

PRECISION TIG 275

Page 22
Image 22
Lincoln Electric SVM162-B Operation for Codes Above 11000 only, Select, Menu Button and Display Switch Codes