Setting the switches | Mitsubishi Electronics CP700E guide

4. Connection with external equipment (RGB Analog signal)

3Connection with RGB Analog Signal equipment

,When connecting the unit with another equipment, make sure to set the power of each equipment to “OFF”.

RGB Analog signal equipment

To RGB Analog IN

SCAN START

terminal (

)

R

G/G+SYNC.

B

SYNC.-H+V

RECORD

RED

CONTRAST

SCAN SPEED

In case of SYNC ON G.

REPLAY

GREEN

BRIGHTNESS

signal, it is not

ON

OFF

10 KEY

BLUE

POWER

necessary to connect to

RESET

WHITE

BALANCE

the unit.

VCP

H+V-SYNC.

G/G+SYNC.

1

2

B

R

RS-232C

REMOTE

VIDEO

S-VIDEO

AC LINE

IMPEDANCE

R

G/G+SYNC

B

H+V-SYNC

RGB

IN

75Ω

HIGH

SYNC.

OUT

75Ω

R

G/G+SYNC

B

H+V-SYNC

HIGH

To RGB Analog OUT terminal

,Use BNC type cable on the market for connection.

,This unit functions at 15.625 kHz for H and 50Hz for V.

Setting the switches

,Set the impedance switches “IMPEDANCE” on the rear panel to the impedance of the equipment connected.

Normally,

a.Set the RGB analog signal to “75Ω”. b.Set the sync signal to “HIGH.

IMPEDANCE

RGB

75Ω Impedance switch for RGB analog signal

HIGH

SYNC.

75Ω

HIGH Impedance switch for sync. signal

NOTE: • When the power turns off or the display is not appeared with analog through mode, the impedance switch is not available. So, connect the unit with the side of monitor or external terminal .

• When connecting to a monitor, use the monitor with 75Ω.

18

Image 19

Mitsubishi Electronics CP700E operation manual Connection with external equipment RGB Analog signal, Setting the switches

Contents

CP700E Contents Power Requirement Precautions Be Careful with the Printing Unit Precautions Safety Checks Remove the fixed screw on the printing unit Installing the lithium batteryInstalling the print paper and ink cassette Setting the present time Preparations before operation Installing the lithium battery Installation procedure of print paper Installing print paper and ink sheet Install the ink cassette Install the ink sheet1Set the printing unit After printing Precautions before printing Main Menu Menu display Setting the day and present time Setting the present time Setting the present time Change Change the date and present time setting Connection with RS-232C equipment Connection with RGB Analog Signal equipmentConnection with external equipment Connection with Monitors Connection with external equipment Monitor OFF Setting the output sync. signal Output Sync VCP Video signalConnection with external equipment VIDEO/S-VIDEO Video Setting the switches Connection with external equipment RGB Analog signal Displaying the menu screen Setting Baud RateDisplaying System Set Menu Connection with external equipment RS-232C Interface Setting the RS-232C Command Type RS-232C Data Signal Front Panel Features and functions Inside of Printing Unit Features and Functions Rear Panel Potential equalization connector Color Adjust Remote Control Print button Printing Printing procedures Basic printsContinuous printing FIELD/FRAME Printing Procedures Basic printsPrinting Selecting Field or Frame Selecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the images E L D Setting the number of printsCancelling continuous printing Continuous printing Changing the number of prints during printing Setting the functions Operation Setting the functions Button function setting display Main Menu Memory SW menu Y L O C K Displaying menu screenMemory SW Menu sub menu display Displaying the sub menu SET Function Setting the functions Main menuMain Menu Color ADJ Adjusting the color of the image Function Adjust the red-subcontrast of printing image Signal selecting menu Signal SETRGB Photo Special print settingAdditional Same Echo Print Print settingNML Deep ADJ COMData System System settingComment Making a comment 1USER Size ADJ Setting the image size Making a comment Setting the functions Making a comment Menu display Remote control function on the comment display Editing command Comment making procedure Selecting comment block Inputting the letter Case of deleting E Close the comment menu Cancel Setting the functions Memory SW menuSetting Functions Memory SW Menu Change OK / CANCEL/ Init Setting the buttons function Time ADJ Setting the day and present timeKEY SET ADJ Signal setting display Signal Print SET Print setting Margin cut High RET ReturnLOW Following printing is available Printing procedures Special prints Image prints Multi prints Printing Procedures Special printsAbcd Images Image size and the number of memory pages Multi Prints Setting the multi-print menu 1Displaying the image from input signal source image Storing images in memory Field 1Printing the images Photo Prints Setting Photo print menu Selecting the size Displaying the image from input signal source image Printing the images Separate Print 1Setting the Separate function Setting the multi-print and photo-print menus1Displaying the source image image from the input signal Strobe Prints Selecting Field or Frame Setting Strobe function1Storing images in memory / Printing the images Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signal Automatic interval prints 1 image Settingtheautomaticintervalprinting1Interrupting strobe memory Pressing the Print button 1Interrupting automatic interval prints Pressing the Memory button Remote External Remote 2 terminal on the rear panelMemory Busy Pin No Remote terminal Circuit inside the VCP External Remote 1 terminal on the rear panel Timing Chart Troubleshooting Overcoming paper jams Troubleshooting Symptom Before calling for service Troubleshooting K65HM Options Specifications Italian Branch Mitsubishi Electric Europe B.V UK BranchGerman Branch French Branch