Save PRG | Mitsubishi Electronics CP700E specs

6. Printing Procedures (Basic prints)

SET

5Press the SET button.

,“CHANGE : OK” is selected.

,When changing the size setting selected at step 4 , press the RIGHT

	SET
button to select “CANCEL” . Press the SET	button to

select “MODE : S/L” in “4.PRINT” again.

SET

6Press the SET button.

, The MAIN MENU is displayed.

SET

P r i n t M e n u

C H A N G E : O K

M a i n M e n u

4 . P R I N T : P U S H [ > ]

	7 Press the SET	button.
	, “SAVE PRG	1/2/3” is selected.	M a i n M e n u
	, “SAVE PRG	1/2/3” is selected.	S A V E P R G : 1
			S A V E P R G : 1

,This menu is used to store the setting in any one of 3 programs (1, 2 or 3).

8Press the RIGHT or LEFT button to select the program number 1, 2 or 3 to store the setting.

,The setting will be overlaid. In case of keeping the stored program, do not select the program number in which the setting is stored.

SET

9Press the SET button.

,The source image (image from the input signal) is displayed.

,The setting of print size is completed.

32

Image 33

Mitsubishi Electronics CP700E operation manual Save PRG

Contents

CP700E Contents Power Requirement Precautions Be Careful with the Printing Unit Precautions Safety Checks Installing the print paper and ink cassette Installing the lithium batterySetting the present time Remove the fixed screw on the printing unit Preparations before operation Installing the lithium battery Installation procedure of print paper Installing print paper and ink sheet Install the ink sheet Install the ink cassette1Set the printing unit After printing Precautions before printing Main Menu Menu display Setting the day and present time Setting the present time Setting the present time Change Change the date and present time setting Connection with external equipment Connection with RGB Analog Signal equipmentConnection with Monitors Connection with RS-232C equipment Connection with external equipment Monitor OFF Setting the output sync. signal Output Sync Connection with external equipment VIDEO/S-VIDEO Video signalVideo VCP Setting the switches Connection with external equipment RGB Analog signal Setting Baud Rate Displaying the menu screenDisplaying System Set Menu Connection with external equipment RS-232C Interface Setting the RS-232C Command Type RS-232C Data Signal Front Panel Features and functions Inside of Printing Unit Features and Functions Rear Panel Potential equalization connector Color Adjust Remote Control Print button Printing procedures Basic prints PrintingContinuous printing Printing Printing Procedures Basic printsSelecting Field or Frame FIELD/FRAME Selecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Image memorizing with page INC Page Increment function Storing images in memory / Printing the images Cancelling continuous printing Setting the number of printsContinuous printing E L D Changing the number of prints during printing Setting the functions Operation Setting the functions Button function setting display Main Menu Memory SW menu Memory SW Menu sub menu display Displaying menu screenDisplaying the sub menu Y L O C K SET Setting the functions Main menu FunctionMain Menu Color ADJ Adjusting the color of the image Function Adjust the red-subcontrast of printing image Signal SET Signal selecting menuRGB Additional Special print settingSame Photo NML Print Print settingDeep Echo COM ADJData Comment System settingMaking a comment System 1USER Size ADJ Setting the image size Making a comment Setting the functions Making a comment Menu display Remote control function on the comment display Editing command Comment making procedure Selecting comment block Inputting the letter Case of deleting E Close the comment menu Setting Functions Memory SW Menu Setting the functions Memory SW menuChange OK / CANCEL/ Init Cancel Time ADJ Setting the day and present time Setting the buttons functionKEY SET ADJ Signal setting display Signal Print SET Print setting Margin cut RET Return HighLOW Following printing is available Printing procedures Special prints Printing Procedures Special prints Image prints Multi printsAbcd Images Image size and the number of memory pages Multi Prints Setting the multi-print menu 1Displaying the image from input signal source image Storing images in memory Field 1Printing the images Photo Prints Setting Photo print menu Selecting the size Displaying the image from input signal source image Printing the images Separate Print Setting the multi-print and photo-print menus 1Setting the Separate function1Displaying the source image image from the input signal Selecting Field or Frame Setting Strobe function Strobe Prints1Storing images in memory / Printing the images Printing Procedures Special prints 1Storing images in memory Displaying the source image image from the input signal 1Interrupting strobe memory SettingtheautomaticintervalprintingPressing the Print button Automatic interval prints 1 image 1Interrupting automatic interval prints Pressing the Memory button Memory External Remote 2 terminal on the rear panelBusy Remote Pin No Remote terminal Circuit inside the VCP External Remote 1 terminal on the rear panel Timing Chart Troubleshooting Overcoming paper jams Troubleshooting Symptom Before calling for service Troubleshooting K65HM Options Specifications German Branch Mitsubishi Electric Europe B.V UK BranchFrench Branch Italian Branch