Troubleshooting | Mitsubishi Electronics CP700E specs

9. Troubleshooting

Symptom

1The stored image in the memory cannot be enlarged to fill the maximum print area.

1The color or picture quality is different between the memorized image and the printed image.

1The image on the monitor screen printed paper is not colored correctly.

(When the VIDEO signal without color burst signal is inputted to the unit, the image on the monitor screen or printed image becomes monochrome or rainbow-like colored image.)

1The color or picture quality is different between the image on the monitor screen and the printed image. (When the color and picture quality are same between the image stored in the memory and the printed image.)

1The set comments do not appear on the print paper.

1Wired remote control cannot be operated.

Check and Remedy

Is the SMALL size ink-sheet installed when selecting “S” in “MODE : S/L”?

Or is the LARGE size ink-sheet installed when selecting “L” in “MODE : S/L”?

→Check the current setting. Refer to pages 31 - 32.

Is the paper size set to “N” in the size setting in SYSTEM menu?

→Set the size to “M” or “W”. Refer to page 51.

Is the S size image printed on the L size paper?

→Check the current setting. Refer to pages 31 - 32.

Is the print area set correctly in the USER SIZE ADJ?

→Check the setting of the print area. Refer to pages 52 - 53.

Is the color of the image stored in the memory adjusted?

→Adjust the color of the image stored in the memory with the image adjustment display (COLOR ADJ). Refer to pages 45 -46.

Is the DCF set to “OFF”?

→Set the DCF to “OFF”. Refer to page 47.

Is the image on the monitor screen adjusted?

→Adjust the image on the monitor screen with “MON R-SUB” and “MON B-SUB” in the SIGNAL ADJ menu in the signal setting display. Refer to page 62.

Is the COMMENT set to “OFF”?

→Set the COMMENT to “COM”. Refer to page 50. Is the COMMENT inputted?

→Input the COMMENT on the menu. Refer to page 56.

Is the plug of the remote control disconnected from its terminal on the unit?

→Connect the plug of the remote control to the REMOTE terminal on the unit.

Is the wired remote control for this unit (accessory) used?

→Use the remote control for this unit.

Is this unit operated through RS-232C interface?

→Set “KEY MASK” to “OFF” through RS-232C interface.

87

Image 88

Mitsubishi Electronics CP700E operation manual Troubleshooting

Contents

CP700E Contents Precautions Power Requirement Precautions Be Careful with the Printing Unit Safety Checks Installing the lithium battery Installing the print paper and ink cassetteSetting the present time Remove the fixed screw on the printing unit Installing the lithium battery Preparations before operation Installing print paper and ink sheet Installation procedure of print paper Install the ink cassette Install the ink sheet1Set the printing unit Precautions before printing After printing Menu display Main Menu Setting the present time Setting the day and present time Setting the present time Change the date and present time setting Change Connection with RGB Analog Signal equipment Connection with external equipmentConnection with Monitors Connection with RS-232C equipment Connection with external equipment Monitor Setting the output sync. signal Output Sync OFF Video signal Connection with external equipment VIDEO/S-VIDEOVideo VCP Connection with external equipment RGB Analog signal Setting the switches Displaying the menu screen Setting Baud RateDisplaying System Set Menu Setting the RS-232C Command Type Connection with external equipment RS-232C Interface RS-232C Data Signal Features and functions Front Panel Features and Functions Inside of Printing Unit Potential equalization connector Rear Panel Remote Control Color Adjust Print button Printing Printing procedures Basic printsContinuous printing Printing Procedures Basic prints PrintingSelecting Field or Frame FIELD/FRAME Selecting input signal Press the SET button Main Menu is displayed 1Setting print size S/L Save PRG Memory Storing images in memory / Printing the images Image memorizing with page INC Page Increment function Setting the number of prints Cancelling continuous printingContinuous printing E L D Changing the number of prints during printing Setting the functions Setting the functions Operation Button function setting display Main Menu Memory SW menu Displaying menu screen Memory SW Menu sub menu displayDisplaying the sub menu Y L O C K SET Function Setting the functions Main menuMain Menu Adjusting the color of the image Color ADJ Function Adjust the red-subcontrast of printing image Signal selecting menu Signal SETRGB Special print setting AdditionalSame Photo Print Print setting NMLDeep Echo ADJ COMData System setting CommentMaking a comment System Setting the image size 1USER Size ADJ Setting the functions Making a comment Making a comment Remote control function on the comment display Menu display Comment making procedure Editing command Inputting the letter Selecting comment block Case of deleting E Close the comment menu Setting the functions Memory SW menu Setting Functions Memory SW MenuChange OK / CANCEL/ Init Cancel Setting the buttons function Time ADJ Setting the day and present timeKEY SET Signal ADJ Signal setting display Print setting Print SET Margin cut High RET ReturnLOW Printing procedures Special prints Following printing is available Image prints Multi prints Printing Procedures Special printsAbcd Image size and the number of memory pages Images Setting the multi-print menu Multi Prints 1Displaying the image from input signal source image Storing images in memory 1Printing the images Field Setting Photo print menu Photo Prints Displaying the image from input signal source image Selecting the size Separate Print Printing the images 1Setting the Separate function Setting the multi-print and photo-print menus1Displaying the source image image from the input signal Strobe Prints Selecting Field or Frame Setting Strobe function1Storing images in memory / Printing the images Printing Procedures Special prints Displaying the source image image from the input signal 1Storing images in memory Settingtheautomaticintervalprinting 1Interrupting strobe memoryPressing the Print button Automatic interval prints 1 image Pressing the Memory button 1Interrupting automatic interval prints External Remote 2 terminal on the rear panel MemoryBusy Remote Circuit inside the VCP Pin No Remote terminal Timing Chart External Remote 1 terminal on the rear panel Troubleshooting Troubleshooting Overcoming paper jams Before calling for service Symptom Troubleshooting Options K65HM Specifications Mitsubishi Electric Europe B.V UK Branch German BranchFrench Branch Italian Branch