Manuals / Nortel Networks / Communications / Telephone

Nortel Networks MICS-XC manual Bracket termination board

Models: MICS-XC

1 138

Download 138 pages 24.91 Kb

Page 40

34 / Installation

To mount a Base Station:

1.Fasten the bracket into position using two #8 38-mm (11/ 2-in.) screws.

2.Route the cable from the ICS through the top (or bottom) opening.

3.Wind any excess cable around the posts to secure it, then fasten it under the strain relief.

4.Connect the wires to the BIX connector on the bracket termination board as shown in the following illustration.

The polarity of the TCM connections is not important. If two power pairs are brought in, they must be connected with the same polarity to the Base Station bracket termination board.

Ensure that the RPI is off before connecting power pairs to the Base Station.

Bracket termination board

TCM

TCM

-PWR(1)

+PWR(1)

-PWR(2)

+PWR(2)

RJ11 jack

MICS-XC Norstar-Companion Installer Guide

P0881594 Issue 01

Image 40

Nortel Networks MICS-XC manual Bracket termination board

Contents

Norstar-Companion Installer Guide MICS-XCPage Table of Contents Powering up the system Programming Troubleshooting TestingRegistering individual portables Upgrading your system SpecificationsGlossary Index Regulations Federal Communications Commission U.S. onlyCompanion Base Stations Activation U.S. onlySafety Norstar Companion basics Norstar Companion basics Norstar Companion basics Norstar Companion basics New features Wireless call pickup featuresWhat’s new with Norstar Hunt GroupsWireless Call Forward No Answer enhancement Wireless Portable Language SelectionWireless Twinning enhancement Planning the installation Planning checklistConfiguring Station Modules Required equipment and suppliesConfiguring expansion modules SM13 SM14On a mini system On a midi systemTwo-port Expansion Cartridge On a maxi system Six-port Expansion Cartridge with CompanionOn a mega system Port Expansion Cartridge with Companion Routing fiber cables ICS numberingNon-expanded system ICS alone numbering Two-port Expansion Cartridge and ICS numbering Six-port Expansion Cartridge and ICS numberingTwelve-port expanded system and ICS numbering Installation Installation checklistConnecting expansion modules Installing Remote Power Interconnect RPI unitsRPI unit Mounting the RPI unit RPI RequirementsBase Stations RPI-16 and RPI-8 required PSUs required RPI-16 PSUs 17-24 RPI-16 and 1 RPI-8 25-32Opening the RPI cover Wiring the RPI RPI componentsRPI Connector Overview Wire size Single-pair Double-pairOutput connections Input wiring Connector Pin Signal OutputRPI-8 BIX wiring chart Pin RPI Connector Board Label Wire colorInstallation RPI-16 BIX wiring chart Installing Base Stations Positioning a Base Station Minimum distance between office areas and Base Stations Mounting a Base StationClearance for the Base Station Bracket termination board Installation Installing portable telephones Sliding cover onto bracketInstalling external antennas and lightning surge arrestors FCC requirements Installed antenna and lightning surge arrestor Planning for an outdoor external antenna Installing a lightning surge arrestor Antenna with antenna bracketLightning surge arrestor and bracket Installation 44 / Installation Powering up the system If display shows See46 / Powering up the system Programming Programming overviewBasic password Services Sys speed dial PasswordsTelco features MaintenanceNorstar telephone Programming toolsProgramming overlay Placing the programming overlay Norstar display buttons Special characters on the displayViewing your programming updates Norstar Programming RecordExiting programming Entering numbersTemplate defaults Passwords defaultsStartup defaults Reg. pswdSystem prgrming defaults Startup programmingPerforming Startup CompanionEntering programming Changing the default template¤ﬂﬂ‹›› Entering programming for installers Entering programming for system coordinatorsEntering programming using other passwords Norstar featuresPortable features Registration password Changing the Registration passwordDefault Registration password is Radio ‡¤‹›ﬂ Change password to avoid incorrect registrationCompanion programming RegistrationDeregistering a portable Radio data Schedule re-evaluation during least busy call timesRadio programming settings apply to Base Stations Alarm Definition Re-eval occurred?Antenna Type Cells System logical identifier LID Changing system LID de-registers all portablesBase Station must be installed and powered first Software keys U.S. onlyTerminals&Sets Call the Nortel Customer Response Center Portable Credit Key Configure Base Stations and portables Registering individual portables Registering the C3050C3050 Icons To register the C3050Registered as Nortel To confirm that the C3050 is registered Press Òor Ò. You hear a dial tone, and the portable displaysDeregistering the C3050 To deregister the C3050To measure undirected Rssi Measuring Rssi for a C3050Measuring directed Rssi Use the Companion Provisioning Record to find the following Registering the C3020 Canada only To register the C3020Radio Deregistering the C3020 Canada only To deregister the C3020Measuring Rssi for a C3020 Canada only Measuring undirected RssiBefore you begin measuring directed Rssi Measuring directed Rssi using your portable After registering the portablesRegistering individual portables 86 / Registering individual portables Testing the Companion portable telephones TestingTesting the Base Stations Testing the system coverage Problems with a portable telephone TroubleshootingProblems with a Base Station 90 / Troubleshooting Replacing a Base Station Verifying Radio Credits U.S. only Press ƒ¤ﬂﬂ‹›› ÇØˆÏÈÌProblems with an RPI Obtaining a Recovery Key U.S. only Problems with wireless communicationObtaining a Regression Key U.S. only Displays Alarm codesExample Meaning Possible causes Display Actions 96 / Troubleshooting Re-Eval Utam key Troubleshooting Event message display Event messagesCause Evt308-0103 Disablement test is active Disablement test is finishedEvent message display Cause Only radio credits decreasedWireless system access error Wireless system software error in dealing with aWireless system software error Portable telephoneEvent message display Cause Internal radio driver error Synchronization errorBase Station software error Station that an error has occurredEvt869 Evt879 Remote Power Interconnect SpecificationsNorstar Companion system components Base Station plug-top power supply Base StationExternal antenna assembly For the US Outdoor omni-directional antenna For Canada Lightning surge protectorAdding Companion to a mini, midi, maxi, or mega system Upgrading your systemUpgrading an RPI-8 to an RPI-16 RPI connections Glossary Call Transfer See Transfer Companion portable telephoneDirectory number DN a unique ICS integrated communication system The central hardwareƑﬂ› Key Service Unit KSU PleaseLine Pool Portable Credits U.S. only Receive Signal Strength Indicator Recovery Key U.S. only SeeRemote Power Interconnect RPI Registration password aSee also Utam Inc Utam Recovery Key U.S. only Undirected Receive Signal Strength IndicatorUtam Activation Key U.S. only Utam Inc. U.S. only The FederalIndex Utam code reqÕd Utam test failedEvt 275-3546 S8 Evt 301-1031 S5 Index 124 / Index Index 126 / Index Index 128 / Index Tell us what you think Nortel Product Training and DocumentationIs it easy to find information in this document?