Nortel Networks NN44200-313 guide

44CallPilot server installation

3Install the power cords to all devices, but plug them only into the receptacle, not into the end device. The devices requiring power are:

•1005r server — two power cords, redundant power supplies

•600r server — one power cord

•monitor — one power cord

•tape drive — one power cord

•ELAN subnet Ethernet switch or hub — one power cord

•Nortel server subnet Ethernet switch or hub — one power cord

Note: The single-point ground (SPG) required by the system can be an isolated ground (IG) bus or AC equipment ground (ACEG) bus in the service panel or transformer. The system must be connected to a safety ground or protective earth in accordance with NEC requirements. For international use, the system must be connected to safety ground or protective earth in accordance with Paragraph 2.5 of EN60950/IEC950.

4Check the version of your MPB96 card or cards before proceeding. The versions are identiﬁed as follows:

•The NTRH40CA MPB96 board has three RJ-45 connectors on its faceplate. If you have an NTRH40CA, proceed to step 5.

•The NTRH40AA MPB96 board has a single DB-44 connector on its faceplate. The MPB96 connects to the MGate using a DS30X cable. If you have an NTRH40AA, proceed to step 6.

5Install and connect the DS30 cables from the switch MGATE card to the CallPilot MPB96. There is no restriction as to which cable is connected ﬁrst, as the NTRH40AC MPB96 can get its timing from any of the three RJ-45 ports.

•The RJ-45 connectors in the top MPB96 card are numbered from 1 to 3 starting at the right side of the server’s back panel (next to the power supplies) They are cabled to MGate cards 1 to 3 respectively

•If there are three MPB96 cards in your server, the RJ-45 connectors in the middle card are cabled (from right to left) to MGate cards 4 to 6. The bottom MPB96 card is not connected to the switch.

Continue with "Performing preboot checks" (page 45)

Nortel CallPilot

Quickstart Guide

NN44200-313 01.02 Standard

5.019 May 2008

Copyright © 2007-2008, Nortel Networks

Image 44

Nortel Networks NN44200-313 quick start Continue with Performing preboot checks

Contents

Quickstart Guide Page Page Page Contents CallPilot server preinstallation Getting help from the Nortel Web site How to get helpGetting help over the phone from a Nortel Solutions Center Getting help through a Nortel distributor or reseller CallPilot 5.0 installation Prerequisites to CallPilot 5.0 installation CallPilot 5.0 installation tasks CS 1000/M1 system status check tasks Time requirements Time requirements Task Time to completion CallPilot 5.0 installation CS 1000/M1 system status check CS 1000/M1 system status check tasks Checking the current IP address of the PBX LD Checking the currently conﬁgured VAS IDs Checking the status of the Elan connection to the PBX LD Checking the Elan interface status of the PBX LDEnabling the Elan interface of the PBX LD 16 CS 1000/M1 system status check CallPilot resource conﬁguration CallPilot resource conﬁguration tasks LD 17 Conﬁguring the VAS ID Prompt Response Conﬁguring a new Elan ID and VAS ID LDLD 17 Conﬁguring the Elan ID Prompt Response Conﬁguring system parameters LD Prompt ResponseSecu YES LD 17 Conﬁguring system parameters Prompt Response Deﬁning CallPilot in the customer data block LD LD 15 Conﬁguring End-to-End Signaling Tone Prompt Response LD 15 Conﬁguring Call Redirection Prompt Response Conﬁguring the Route Data Block LD Isdn YESPNI Hloc Conﬁguring Automatic Call Distribution LD LD 16 Conﬁguring the Route Data Block Prompt ResponseRoute Idef LOC Rcls EXT Conﬁguring the Dfdn LD REQ NEW Type ACD CustAcdn MWC Maxp Conﬁguring the CDN queue LD LD 23 Conﬁguring Dfdn Prompt ResponseNcfw LD 23 Conﬁguring the CDN queue Prompt Conﬁguring ACD agents LD Type CDN CustDfdn LD 11 Conﬁguring ACD agents Prompt Response Provisioning telephones LD CLSKEY KEY MSB NRD TRN LD 11 Provisioning telephones Prompt Response ZoneFDN CLS FNA MWA HTA Hunt Enabling card slots LD Saving CS 1000/M1 changes LD 600r CallPilot server front panel CallPilot server general description600r CallPilot server Back panel 600r CallPilot server front panel LEDs Label Description 1005r CallPilot server USB ID LEDDVD/CD/CD-RW Label Description Label Description USB 0 dongle connects here CallPilot server preinstallation Recommended tools Preparing the site CallPilot server preinstallation tasksChoosing a location Connecting to the network Unpacking the server End Rack-mounting the server CallPilot server installationCallPilot server installation tasks Installing peripheral devices Installing cables and grounds Continue with Performing preboot checks Performing preboot checks Connecting the server to power and starting it Step Action Completing the Setup Wizard and installing PEPs CallPilot server conﬁgurationCallPilot server conﬁguration tasks Logging on to the CallPilot server CallPilot server conﬁguration Mailbox number Password Running the Conﬁguration Wizard Type the Computer name From the Application Name list, select Voice Messaging Conﬁguring new mailboxes and additional tasks From the Template Name list, select Regular User Template Backing up the system End Checking CallPilot connectivity and channels CallPilot server testingCallPilot server testing tasks Verifying that you can log on to mailboxes Verifying that you can leave a message Verifying that you can retrieve a message Testing pcAnywhere using a remote PC What is next? Following is a complete list of CallPilot 5.0 NTPs CallPilot server testing Appendix Installing the CallPilot 5.0 image Installing the CallPilot 5.0 image Return to CallPilot server conﬁguration Conﬁguring a phantom superloop Appendix Conﬁguring phantom DNsChecking for existing phantom loops Cden Creating a phantom DNLD 10 Creating a phantom DN Prompt Response CLS WTA UNR FTR Quickstart Guide