Paradyne 3810 manual V22b Guard Tone Disable Nxt Disable 550Hz 1800Hz

Configure Branch

Table 9-4

(2 of 3)

Dial Line Configuration Options

V32bis Autorate: Enable

Nxt Enable Disable StartAt48 StartAt96

Enable ± Once connected, the modem automatically lowers the line rate if line conditions become impaired. When line conditions improve, the modem automatically shifts up to the highest data rate the line can support. This autorating only occurs between 14,400 bps and 4800 bps during V.32/V.32bis connections.

Disable ± Line rate does not vary.

StartAt48, StartAt96 ± Useful for lines with known noise problems, these settings cause the modem to connect at 4,800 bps (StartAt48) or 9,600 bps (StartAt96). If line conditions warrant it, the modem shifts up to the next higher rate until 14,400 bps or the highest possible rate for the line is reached.

The factory default is Enable.

AT command for V.32bis Autorate is S-register S76 = n, where n is 0 for Enable, 1 for Disable, 2 for StartAt48, and 3 for StartAt96.

Dial TX Level: Permissv(±9)
Nxt Permissv(±9)		Programmable ±10 dBm ±11 dBm ±12 dBm ±13 dBm					±14 dBm ±15 dBm ±16 dBm
±17 dBm	±18 dBm	±19 dBm	±20 dBm	±21 dBm	±22 dBm	±23 dBm ±24 dBm ±25 dBm ±26 dBm
±27 dBm	±28 dBm	±29 dBm	±30 dBm	±31 dBm	±32 dBm	ETC 1.0_Cell	ETC 1.1_Cell

Dial Transmit Level. Sets the power output level of the transmit signal over dial lines.

Permissive (±9 dBm) ± The modem transmits data at approximately ±9 dBm. This is true whether the modem is connected to an RJ11-type permissive jack or to an RJ41 or RJ45 programmable jack.

Programmable ± The modem transmits at a predetermined level set by programming a resistor in the RJ41 or RJ45 jack. The program resistor value is only read upon power-up or after reset.

ETC 1.0_Cell ± Transmit level is automatically adjusted in response to line conditions according to the proprietary Enhanced Throughput Cellular 1.0 specification. Use only with remote modems set to ETC 1.0_Cell, and limit the data rate to 4800 bps.

ETC 1.1_Cell ± Transmit level is automatically adjusted in response to line conditions according to the proprietary Enhanced Throughput Cellular 1.1 specification.

The factory default is Permissv(±9).

AT command for Permissive mode is &J0.

AT command for Programmable mode is &J1.

AT commands for ±10 through ±32 dBm are &I10 through &I32.

AT command for ETC 1.0_Cell is &I99.

AT command for ETC 1.1_Cell is &I100.

V22b Guard Tone: Disable

Nxt Disable 550Hz 1800Hz

V.22bis Guard Tone. Determines whether the V.22bis guard tone is disabled, set to 550 Hz, or set to 1800 Hz.

Disable ± No guard tone.

550 Hz or 1800 Hz ± When the modem is in Answer mode, it transmits the guard tone at this frequency.

The factory default is Disable.

AT command to disable is &G0. AT command for 550 Hz is &G1.

AT command for 1800 Hz is &G2.

3810-A2-GB30-20 November 1996 9-27