RAD Data comm ASMi-52 Quick Start Guide

ASMi-52 Ver. 2.5 Configuring ASMi-52 1

Quick Start Guide

Installation of ASMi-52 should be carried out only by an experienced technician. If

you are familiar with ASMi-52, use this guide to prepare the units for operation.

1. Installing ASMi-52

Connecting the Interfaces

1. Connect the line to the RJ-45 rear panel connector dedicated SHDSL.

2. Connect the DTE to the appropriate rear panel connector.

3. Connect the control terminal to the rear panel CONTROL connector.

Connecting the Power

• Connect the AC or DC power to the ASMi-52 modem.

The unit has no power switch. Operation starts when power is connected

to the rear panel power connector.

2. Configuring ASMi-52

Configure ASMi-52 to the required operation mode via an ASCII terminal

connected to the rear panel CONTROL port directly or via a modem link.

Connecting the Terminal

 To connect the terminal:

1. Connect the terminal cable to the CONTROL connector of ASMi-52.

2. Turn the control terminal on.

3. Configure the terminal to the default communication parameters: 9.6 kbps,

one start bit, eight data bits, no parity, one stop bit.

4. Select the full-duplex mode.

5. Turn the terminal echo off.

6. Disable any type of flow control.

You are now ready to start a control session.

Contents

Main Page ASMi-52 Version 2.5 2/4-Wire SHDSL Modem Installation and Operation Manual Notice Limited Warranty General Safety Instructions Safety Symbols Handling Energized Products General Safety Practices Connection of AC Mains Connection of DC Mains Connection of Data and Telecommunications Cables Electromagnetic Compatibility (EMC) FCC-15 User Information Caution Canadian Emission Requirements Warning per EN 55022 (CISPR-22) Declaration of Conformity Quick Start Guide 1. Installing ASMi-52 Connecting the Interfaces Connecting the Power 2. Configuring ASMi-52 Configuring the Master Clock Configuring the SHDSL Interface Configuring the DTE Interface Configuring the Serial Interface Configuring the E1 Interface Configuring the T1 Interface Configuring the 10/100BaseT Interface Page Contents Page Chapter 1 Introduction 1.1 Overview Versions DTE Interface Line Interface Applications Page Features Functionality Line Interface DTE Interface Note Table 1-2. ASMi-52 Data Rates Table 1-3. ASMi-52 Data Rates (Low Speed Mode) Multiplexer Applications Software for a multiplexer version is available but is not transferable to a single port unit. Table 1-4. Possible Multiplexer Applications Timing Management EOC ConfiguRAD Dial-In Dial-Out 1.2 Physical Description 1.3 Functional Description Not e Page 1.4 Technical Specifications Page Page Page Page Chapter 2 Installation and Setup 2.1 Introduction 2.2 Site Requirements and Prerequisites 2.3 Package Contents 2.4 Connecting the Interface Cables Connecting the Line Connecting the DTE Interface Connecting the Alarm Relay Connector 2.5 Connecting the Power Cables Connecting AC Power Connecting DC Power Chapter 3 Operation 3.1 Turning On ASMi-52 3.2 Controls and Indicators Page Normal Indications 3.3 Default Settings Page 3.4 Configuration Alternatives Managing ASMi-52 via a Terminal Port Control Port Interface Characteristics Preparing the Terminal Data Terminal Ready (DTR) Initiating a Control Session Navigating the Management Menus Choosing Options Note Correcting Entries Navigating Data Forms Managing ASMi-52 via Ethernet Port Managing ASMi-52 via a Dedicated Timeslot Managing ASMi-52 via Web Browser Configuration Menus Page Page Logging Out 3.5 Turning Off ASMi-52 Chapter 4 Configuration 4.1 Configuring ASMi-52 for Management Configuring Management Parameters Entering Device Information Configuring the Host Parameters Configuring the Network Managers Controlling the Management Access Configuring Dedicated Timeslots Configuring VLAN Encapsulation Configuring the LAN Port Configuring the LAN Port Operation Mode Filling out the Bridging Table Configuring Aging Timeout Configuring QoS Mapping Setting the LAN Rate Setting the LAN Rate in a Multiplexer Unit Configuring Autonegotiation Configuring Fault Indication 4.2 Configuring ASMi-52 System Parameters Page Configuring the Master Clock Configuring Local Card Mode Configuring Remote Card Mode Configuring Low Speed Operation Configuring Control Port Parameters Changing the Control Port Data Rate Selecting the Control Port Interface Selecting the CTS State Selecting the DSR State Configuring the Terminal Port Configuring the Port Control Mode Configuring User Name, Password, Pop-up Alarms and Security Timeout Page Page Setting the G.704 Interface Type 4.3 Configuring the Physical Ports Configuring the SHDSL Interface Configuring the Power Backoff Configuring the Snext Margin Configuring the Current Margin Configuring the Power Spectral Density Configuring Line Probing Setting the Loop Attenuation Threshold Setting the SNR Margin Threshold Configuring the SHDSL Repeater Configuring the DTE Interface Data Rate Configuring the Data Rate in a Multiplexer Unit Configuring the E1 Interface Selecting E1 Framing Mode Enabling CRC-4 Code Generation Setting the Sync Mode Not e Defining Idle Code Mapping E1 Timeslots Mapping E1 Timeslots in a Multiplexer Unit Matching Remote Unit Settings With Local Unit Settings Configuring the T1 Interface Page 4.4 Additional Tasks Displaying the ASMi-52 Status Displaying the System Status Figure 4-39. System Status Screen Alarms are described in Chapter 5. Displaying the Port Status Figure 4-40. Port Status Menu Accessing the Remote ASMi-52 Entering the User Name and Password Page Displaying the ASMi-52 Inventory Updating Software Releases Installing a New Software Release via TFTP Installing a New Software Release via XMODEM Autoconfiguration through TFTP or XMODEM Displaying the Software Version Switching the Software Versions Resetting ASMi-52 Resetting to Default Settings Resetting the ASMi-52 Modem Resetting the SHDSL Repeater Exiting the Control Session Chapter 5 Configuring a Typical Application 5.1 Overview Application Guidelines for Configuring ASMi-52 Units 5.2 Configuring the ASMi-52 units Setting the ASMi-52 System Parameters Setting the E1 Port Configuring the Line Interface Type Configuring the Serial DTE Interface Configuring LLB/RLB Activation from DTE Page Page Chapter 6 Troubleshooting and Diagnostics 6.1 Monitoring Performance Displaying SHDSL Statistics Displaying the Current SHDSL Statistics Page Displaying the SHDSL Statistics for all Intervals Clearing the SHDSL Performance Statistics Displaying E1/T1 Statistics Displaying the Current E1/T1 Statistics Figure 6-9. E1/T1 Current Day Performances Screen Table 6-2. E1/T1 Statistics Parameters Displaying E1/T1 Statistics for All Intervals Clearing the E1/T1 Statistics 6.2 Detecting Errors Power-Up Self-Test Front Panel LEDs 6.3 Handling Alarms Displaying All Alarms Working with the System Log File Displaying the Port Status Figure 6-14. Physical Port Status Menu Masking Port Alarms ASMi-52 allows you to mask alarms generated by local and remote devices. Page Page Page 6.4 Troubleshooting Working with the Port Log File 6.5 Testing ASMi-52 Bit Error Rate Test (BERT) BERT Patterns Page Running Loopback Tests Loopback in Multiplexer Units Running the Local Loopback Page Running the Remote Loopback Running Remote Loopback at a Repeater Deactivating the Loopbacks Running the LEDs Test 6.6 Frequently Asked Questions Page Page Appendix A Interface Connector Specifications A.1 DTE Interface Connectors V.35, X.21 and RS-530 Interface Connectors Table A-1. V.35, X.21 and RS-530 Connector Pinouts (Cont.) E1 and T1 Interface Connector Ethernet Connector A.2 CONTROL Connector A.3 Alarm Relay Connector Page Appendix B IR-IP Interface Module B.1 Introduction Overview Application B.2 Technical Specifications B.3 Physical Description IR-IP DIP Switch IR-IP LEDs Normal Indications Power-Up Indications for Unconfigured IP Router Card Power-Up Indications for Configured IP Router Card Indications during Normal Service B.4 IR-IP Management Subsystem Accessing the IR-IP Management Subsystem Default IP Communication Parameters B.5 Performing Preliminary Configuration Outline of Preliminary Configuration Connecting the Telnet Host Preliminary Telnet Host Configuration Assigning the Router LAN Interface Address IP Learning Mechanism Assigning a LAN IP Address to a New IR-IP Changing the LAN IP Address of a Configured IR-IP B.6 IR-IP Management Utility General Operating Procedures Appendix B IR-IP Interface Module Installation and Operation Manual B-10 IR-IP Management Utility ASMi-52 Ver. 2.5 Starting a Management Utility Menu Structure of Management Utility Figure B-4 shows the menu structure of the IR-IP management utility. Figure B-4. Management Utility, Menu Structure B.7 Quick Setup Guide Figure B-7. Selecting the IP Subnet Mask Leaving the DHCP Server IP Address field blank disables the DHCP relay. 3. Set the protocol requirements. B.8 Defining Management Access Defining a Telnet Password Setting Telnet Inactivity Timeout B.9 Advanced Setup Defining the Device Identification Defining the Interface Parameters Page Defining the WAN Protocol Parameters Frame Relay Protocol PPP Protocol Menu Defining the Multicast Parameters B.10 Using the Device Control Menu Downloading New Software Viewing the Error Log Erasing Configuration Resetting IR-IP Reset LAN Reset WAN B.11 Viewing IR-IP configuration Data Viewing Configuration and Connection Viewing the ARP Tables Viewing the Multicast Groups Table Viewing the Statistics Screen Figure B-23. WAN Statistics Screen B.12 Using Diagnostic Tools (Ping Terminal) Figure B-24. Diagnostic Tools Menu This section provides information on the diagnostic tool provided with IR-IP (the ping utility). In the Main menu, select Diagnostic Tool. The Diagnostic Tools menu appears (Figure B-24). Using the Ping Function B.13 Erasing Users Configuration B.14 Erasing IR-IP Software Erasing Application Software Downloading New Software B.15 IR-IP Troubleshooting Appendix C Easy Config Device C.1 Physical Description C.2 Technical Specifications C.3 Installation Package Contents Connecting the Interface Cable Connecting the Power C.4 Operation Turning the Easy Config On Note Front Panel Controls z x Scrolling the ASMi-52 Menus Accessing the ASMi-52 Menus Choosing Options Entering Alphanumeric Values on the LCD. Assigning Timeslots Turning the Easy Config Off Index Page Page Page Page Page Supplement Drilling Template for Wall Installation Page Customer Response Form Page Error Report