Configuration Menus | RAD Data comm ASMi-52 specification

Installation and Operation Manual	Chapter 3 Operation

•Trace – opens an additional pane for system messages, progress indicators (ping, software and configuration file downloads) and alarms. It is recommended to keep the trace pane open all the time.

•Refresh All – refreshes all screen elements.

Configuration Menus

The following is the menu map of the ASMi-52 management software.

Note Some of the management menu options depend on the type of the DTE interface installed in ASMi-52:

•DTS Configuration (Main menu > Configuration > System Configuration > Management) is available only for the units with E1 or T1 interface.

•LAN Rate (Main menu > Configuration > LAN Configuration > Local LAN Configuration) is available for the units with the user’s 10/100BaseT port.

•Data Rate (Main menu > Configuration > DTE Configuration > DTE Remote Port) is available for the units with a serial DTE interface.

•E1 Configuration (Main menu > Configuration) is available for the units with an E1 local port.

•Figure 3-10illustrates software menus of the unit that operates with SHDSL repeater in the line.

ASMi-52 Ver. 2.5

Configuration Alternatives

3-11

Image 47

RAD Data comm ASMi-52 manual Configuration Menus

Contents

ASMi-52 Page ASMi-52 Limited Warranty Please observe the following precautions General Safety Instructions Connection of DC Mains General Safety PracticesConnection of AC Mains Isdn Ports Safety StatusTNV-2 TNV-3 Electromagnetic Compatibility EMC Canadian Emission Requirements Supplementary Information Safety Connecting the Power Installing ASMi-52Configuring ASMi-52 Connecting the Interfaces Configuring the Serial Interface Configuring the Master ClockConfiguring the Shdsl Interface Configuring the DTE Interface To configure the T1 parameters Configuring the T1 InterfaceConfiguring the 10/100BaseT Interface To configure E1 parameters Quick Start Guide Configuring ASMi-52 ASMi-52 Ver Contents Troubleshooting and Diagnostics Configuring a Typical Application Line Interface OverviewVersions DTE Interface Unit Enclosure Applications ASMi-52 Modems Operating opposite ASMi-52CD Cards Typical Ranges 26 AWG FeaturesData Rate Wire Functionality DTE Interface Sum for all the interfaces ASMi-52 Data Rates Low Speed ModeASMi-52 Data Rates DTE+LAN Multiplexer Applications Serial DTE = V.35, X.21, RS-530, IR-IP Timing Management Diagnostics Statistics Collection Alarm ReportingPhysical Description Functional Description ASMi-52 modem consists of the following major modules Technical Specifications Diagnostics Loopbacks Height PWR green Power Test redPower Consumption Synchronization of DSL line Environment Introduction Technical Specifications ASMi-52 Ver Site Requirements and Prerequisites To install ASMi-52Introduction Connecting the Interface Cables Package Contents Connecting the Alarm Relay Connector Connecting the Power CablesConnecting the Line Connecting the DTE Interface To connect DC power Connecting AC PowerConnecting DC Power To connect AC power To turn on ASMi-52 Controls and IndicatorsTurning On ASMi-52 ASMi-52 Front Panel, E1 Interface 2 Wire ASMi-52 Rear Panel LEDs ASMi-52 Indicator StatusNormal Indications ASMi-52 Front Panel LEDs LAN Configuration Default SettingsDefault Settings Parameter Default Value System OFF Parameter Default Value Control PortDCE CTS =RTS DSR T1 Interface Configuration AlternativesParameter Default Value Serial DTE Interface E1/E1+Ethernet/E1+Serial DTE Interface Data Terminal Ready DTR Control Port Interface CharacteristicsManaging ASMi-52 via a Terminal Port Preparing the Terminal To choose an option Navigating the Management MenusCorrecting Entries Navigating Data Forms To prepare ASMi-52 for network management To start the ConfiguRAD sessionManaging ASMi-52 via Ethernet Port Managing ASMi-52 via a Dedicated Timeslot Managing ASMi-52 via LAN Port and a Dedicated Timeslot Managing ASMi-52 via Web Browser Configuration Menus 10. Inventory and Configuration Menus 11. Monitoring, Diagnostics and File Utilities Menus To turn off ASMi-52 Turning Off ASMi-52Logging Out To end the current session MTU means Maximum Transfer Unit Configuring ASMi-52 for ManagementConfiguring Management Parameters To access the Management menu Type Y to confirm the deletion Entering Device InformationTo enter device information To clear system parameters To define the IP parameters Configuring the Host ParametersConfiguring the Network Managers To configure the network managers To define the management access method Controlling the Management Access To configure dedicated timeslots Configuring Dedicated Timeslots To enable Vlan mode Configuring Vlan Encapsulation With autonegotiation enabled Configuring the LAN PortConfiguring the LAN Port Operation Mode To remove a MAC address from the table Filling out the Bridging TableTo fill out the bridge table To configure Vlan Priority QoS Mapping Configuring Aging TimeoutConfiguring QoS Mapping To configure aging timeout To set the LAN rate Setting the LAN RateInformation to be transmitted to the DSL line To set autonegotiation Setting the LAN Rate in a Multiplexer UnitConfiguring Autonegotiation To access the Configuration menu Configuring ASMi-52 System ParametersConfiguring Fault Indication To set the fault indication To display the System Configuration menu 16. Configuration Menu To configure local card mode Configuring Local Card Mode To enable the low speed operation Configuring Remote Card ModeConfiguring Low Speed Operation To configure remote card mode Changing the Control Port Data Rate Configuring Control Port ParametersTo access the Control port menu To configure the control port data rate Selecting the DSR State Configuring the Terminal PortSelecting the Control Port Interface Selecting the CTS State To access the Terminal menu Configuring the Port Control ModeCurrently, the connection to ASMi-52 via Slip is disabled To enable or disable the pop-up alarms To change the user name and password To change the dial-out parameters To configure the security timeout To set the G.704 interface type Setting the G.704 Interface Type To change the transmission mode Configuring the Physical Ports To configure the Snext margin Configuring the Power BackoffConfiguring the Snext Margin To configure the use of the power backoff To configure the current margin Configuring the Current Margin Setting the Loop Attenuation Threshold Configuring the Power Spectral DensityConfiguring Line Probing To set the SNR margin threshold Setting the SNR Margin ThresholdConfiguring the Shdsl Repeater To access the Shdsl Repeater menu To select the data rate Configuring the DTE Interface Data RateConfiguring the Data Rate in a Multiplexer Unit To access the E1 Port Configuration menu Configuring the E1 Interface To select E1 framing mode Selecting E1 Framing Mode To select resynchronization time Setting the Sync ModeTo enable CRC-4 code generation Enabling CRC-4 Code Generation To assign E1 timeslots Defining Idle CodeMapping E1 Timeslots To define an idle code Opposite remote units with a serial data interface You can configure timeslot 0 to be looped or transparentMapping E1 Timeslots in a Multiplexer Unit To map E1 timeslots in a multiplexer unit with E1 + LAN Matching Remote Unit Settings With Local Unit Settings To match remote unit settings with local unit settings Configuring the T1 Interface 37. T1 Port Configuration To access the T1 Configuration menu Displaying the System Status To access the Monitoring menuAdditional Tasks Displaying the ASMi-52 Status To display the port status information Alarms are described in ChapterDisplaying the Port Status To close a virtual terminal Entering the User Name and PasswordAccessing the Remote ASMi-52 To access the remote ASMi-52 Press Enter Type in your password at the prompt up to eight charactersType in your user name and press Tab ASMi-52 responds to your entry with asterisks To display the ASMi-52 inventory Displaying the ASMi-52 Inventory Updating Software Releases Installing a New Software Release via TftpTo install a new software release via Tftp Port Data Rate section above Displaying the following message To upload a configuration from the source device Autoconfiguration through Tftp or XmodemDuring the software installation, the TST indicator blinks To display the software version To download a configuration file to the target devicesDisplaying the Software Version To swap software versions Resetting ASMi-52Switching the Software Versions Units equipped with the management LAN port Resetting to Default SettingsResetting the ASMi-52 Modem To reset ASMi-52 to the factory default To reset the line interface of the Shdsl repeater Resetting the Shdsl Repeater Exiting the Control Session 52. Repeater Reset Menu Application Guidelines for Configuring ASMi-52 Units To prepare a control session Configuring the ASMi-52 unitsSetting the ASMi-52 System Parameters To enter the user name and password To set the device host IP address Setting the E1 Port To configure the line interface type for ASMi-52 units Configuring the Line Interface TypeConfiguring the Serial DTE Interface Configuring LLB/RLB Activation from DTE DTE Local Port Menu Page To display the current Shdsl statistics Monitoring PerformanceDisplaying Shdsl Statistics Displaying the Current Shdsl Statistics Shdsl Port Performances Menu Display Description Displaying the Shdsl Statistics for all IntervalsShdsl Statistics Parameters To display the Shdsl statistics fo r all intervals Clearing the Shdsl Performance Statistics CRC-4 Enabled E1, ESF framing T1CRC-4 Disabled E1, SF framing T1 Displaying E1/T1 Statistics To display the current E1/T1 statistics Displaying the Current E1/T1 StatisticsChapter Display Description Range To display E1/T1 statistics for all intervals TimerDisplaying E1/T1 Statistics for All Intervals E1 Statistics Parameters Front Panel LEDs Detecting ErrorsHandling Alarms Power-Up Self-Test To display all alarms Displaying All Alarms To clear the system log file Working with the System Log FileDisplaying the Port Status To display the system log file Number Terminal Message Port Description Severity Masking Port AlarmsTo mask ASMi-52 alarms ASMi-52 Alarms and Warnings Losw Failure Over Shdsl CRC Error Over ShdslT1-TS not Rate Comp E1 Signal Loss DTE T1 Signal Loss E1 BPV ERR EXC DTE T1 AIS Occured AIS and Sync DTE Wire Mode not ShdslExcesive ERR DTE Ratio T1 Excesive ERR AIS Occured DTE Internal Clock Customer SideLine Paramers not Shdsl External to DTE To display the log file TroubleshootingWorking with the Port Log File ASMi-52 Events To clear the log file Testing ASMi-52 Bert Patterns Bit Error Rate Test Bert 16. Bert Menu To configure the Bert results Loopback in Multiplexer Units Running Loopback Tests 20. Loopback with Multiplexer Units Running the Local Loopback To run the local loopback 22. Diagnostics Menu To activate the remote loopback Running the Remote LoopbackRunning Remote Loopback at a Repeater To deactivate a running loopback Deactivating the LoopbacksTo activate the remote loopback at the Shdsl repeater To run the LEDs test Frequently Asked QuestionsRunning the LEDs Test To deactivate multiple loopbacks Technical Support Page Table A-1. V.35, X.21 and RS-530 Connector Pinouts DTE Interface Connectors35, X.21 and RS-530 Interface Connectors Description Function 34-Pin DB-25 DB-15 Circuit 35, X.21 and RS-530 Connector Pinouts Ethernet Connector E1 and T1 Interface Connector Cross cable with two male DB-9 connectors Control ConnectorTable A-4. Control Connector Pinout Table A-5. Control Connector Signal Direction DB-9 Pin Alarm Relay ConnectorTable A-6. Cross Cable Pinout Page Overview Appendix B IR-IP Interface Module Interface Type RJ-45 shielded 8-pin connectorOperation Mode Full duplex or half duplex user-selectable Standard Conforms to Ieee Data Rate This appendix IR-IP DIP SwitchTable B-2. IR-IP DIP Switch Functions Table B-1 RJ-45 Pinout Table B-3. IR-IP Interface Indicators Power-Up Indications for Unconfigured IP Router CardPower-Up Indications for Configured IP Router Card Indications during Normal Service IR-IP Management Subsystem Accessing the IR-IP Management Subsystem To perform the preliminary configuration procedure Performing Preliminary ConfigurationDefault IP Communication Parameters Outline of Preliminary Configuration IP Learning Mechanism Connecting the Telnet HostPreliminary Telnet Host Configuration Assigning the Router LAN Interface Address Assigning a LAN IP Address to a New IR-IP To view and edit the ARP table contentsTo configure the IP router LAN address IR-IP Management Utility General Operating ProceduresChanging the LAN IP Address of a Configured IR-IP Documentation to find how to select a proper font Menu Structure of Management Utility Starting a Management Utility To perform quick setup Quick Setup Guide Parameters Default GatewayOperation without Default Gateway Operation with Default Gateway Figure B-7. Selecting the IP Subnet Mask Reading Protocol from DIP Switches To access the Management Access menu Defining Management AccessDefining a Telnet Password Setting Telnet Inactivity Timeout Defining the Interface Parameters Advanced SetupDefining the Device Identification Figure B-10. Interface Parameters Menu To define the Frame Relay protocol parameters Defining the WAN Protocol ParametersFrame Relay Protocol To define the PPP Protocol Parameters PPP Protocol Menu To define the Multicast Parameters Defining the Multicast Parameters To access the Device Control menu Using the Device Control MenuTo access the Static Groups menu To download new software Viewing the Error LogDownloading New Software To reset the LAN interface Erasing ConfigurationResetting IR-IP Reset LAN Reset WAN Viewing IR-IP configuration DataViewing Configuration and Connection Viewing the Multicast Groups Table To access the ARP Tables screenTo access the multicast groups table screen Viewing the ARP Tables Viewing the Statistics Screen To access the Statistics menu To access the Diagnostic Tools menu Using Diagnostic Tools Ping Terminal To ping a host Using the Ping Function Desired positions, and then turn ASMi-52 on again Erasing User’s ConfigurationTo erase the user’s configuration Erasing IR-IP Software To erase the application software Erasing Application Software What to do if the IP learning process is not successful? IR-IP TroubleshootingWhat if there are no ping replies from IR-IP? Escape, Scroll Down, Scroll Right, Enter LCD ScreenControl Port Type, 9-pin, male Connecting the Interface Cable InstallationPackage Contents Front Panel Controls Turning the Easy Config OnWorking with the Easy Config Operation Entering Alphanumeric Values Accessing the ASMi-52 MenusScrolling the ASMi-52 Menus Choosing Options Hold down the z button, until s is displayed in the top row To assign timeslots Turning the Easy Config OffTo turn the Easy Config off Assigning Timeslots Bert Index IR-IP Default settings Log file Logging out Loopback LLB/RLB Tftp Router LAN interface address, B-7 Screen Xmodem Index ASMi-52 Ver Front Panel SupplementPage Excellent Good Fair Poor Very Poor Customer Response FormPage Error Report Page Page International Headquarters