Configuration Alternatives, T1 Interface | RAD Data comm ASMi-52

Chapter 3 Operation		Installation and Operation Manual


	Parameter	Default Value

	Serial DTE Interface

	Rate	Single:
		2-wire – 192 kbps
		4-wire – 384 kbps
		Multiplexer:
		1. E1+Serial DTE, N/A, 0 kbps
		2. LAN+Serial DTE:	2-wire – 192 kbps
			4-wire – 384 kbps

	LLB from DTE	Disable

	RLB from DTE	Disable

	E1/E1+Ethernet/E1+Serial DTE Interface

	Framed mode	Unframed

	Sync	CCITT

	CRC-4	No

	Idle Code	ff

	Units identical settings	Yes

	T1 Interface

	Framed mode	Unframed

	Line code	B8ZS

	Receive gain	Long

	Interface	DSU

	Transmit signal mask	0 feet

	Fbit configuration	Transparent

	Sync mode	Fast (after 1 sec)

	Idle code	Ff

	Units identical set	Yes

3.4 Configuration Alternatives

After installation, ASMi-52 can be reconfigured using different ports and applications:

•Local out-of-band management via an ASCII terminal or the Easy Config device connected to the RS-232 port. Usually, preliminary configuration of the system parameters is performed via an ASCII terminal. Once the ASMi-52 host IP parameters are set, it is possible to access it via Telnet, ConfiguRAD, or RADview-Lite for further configuration.

3-6

Configuration Alternatives

ASMi-52 Ver. 2.5

Image 42

RAD Data comm ASMi-52 manual Configuration Alternatives, Parameter Default Value Serial DTE Interface, T1 Interface

Contents

ASMi-52 Page ASMi-52 Limited Warranty General Safety Instructions Please observe the following precautions General Safety Practices Connection of AC MainsConnection of DC Mains TNV-3 Ports Safety StatusTNV-2 Isdn Electromagnetic Compatibility EMC Canadian Emission Requirements Safety Supplementary Information Connecting the Interfaces Installing ASMi-52Configuring ASMi-52 Connecting the Power Configuring the DTE Interface Configuring the Master ClockConfiguring the Shdsl Interface Configuring the Serial Interface To configure E1 parameters Configuring the T1 InterfaceConfiguring the 10/100BaseT Interface To configure the T1 parameters Quick Start Guide Configuring ASMi-52 ASMi-52 Ver Contents Configuring a Typical Application Troubleshooting and Diagnostics DTE Interface OverviewVersions Line Interface Applications Unit Enclosure ASMi-52 Modems Operating opposite ASMi-52CD Cards Functionality FeaturesData Rate Wire Typical Ranges 26 AWG DTE Interface ASMi-52 Data Rates Low Speed Mode ASMi-52 Data RatesSum for all the interfaces Multiplexer Applications DTE+LAN Timing Serial DTE = V.35, X.21, RS-530, IR-IP Diagnostics Management Functional Description Alarm ReportingPhysical Description Statistics Collection ASMi-52 modem consists of the following major modules Technical Specifications Diagnostics Loopbacks Synchronization of DSL line PWR green Power Test redPower Consumption Height Environment Introduction Technical Specifications ASMi-52 Ver To install ASMi-52 IntroductionSite Requirements and Prerequisites Package Contents Connecting the Interface Cables Connecting the DTE Interface Connecting the Power CablesConnecting the Line Connecting the Alarm Relay Connector To connect AC power Connecting AC PowerConnecting DC Power To connect DC power Controls and Indicators Turning On ASMi-52To turn on ASMi-52 ASMi-52 Front Panel, E1 Interface 2 Wire ASMi-52 Front Panel LEDs ASMi-52 Indicator StatusNormal Indications ASMi-52 Rear Panel LEDs Parameter Default Value System Default SettingsDefault Settings LAN Configuration CTS =RTS DSR Parameter Default Value Control PortDCE OFF E1/E1+Ethernet/E1+Serial DTE Interface Configuration AlternativesParameter Default Value Serial DTE Interface T1 Interface Preparing the Terminal Control Port Interface CharacteristicsManaging ASMi-52 via a Terminal Port Data Terminal Ready DTR Navigating Data Forms Navigating the Management MenusCorrecting Entries To choose an option Managing ASMi-52 via a Dedicated Timeslot To start the ConfiguRAD sessionManaging ASMi-52 via Ethernet Port To prepare ASMi-52 for network management Managing ASMi-52 via Web Browser Managing ASMi-52 via LAN Port and a Dedicated Timeslot Configuration Menus 10. Inventory and Configuration Menus 11. Monitoring, Diagnostics and File Utilities Menus To end the current session Turning Off ASMi-52Logging Out To turn off ASMi-52 To access the Management menu Configuring ASMi-52 for ManagementConfiguring Management Parameters MTU means Maximum Transfer Unit To clear system parameters Entering Device InformationTo enter device information Type Y to confirm the deletion To configure the network managers Configuring the Host ParametersConfiguring the Network Managers To define the IP parameters Controlling the Management Access To define the management access method Configuring Dedicated Timeslots To configure dedicated timeslots Configuring Vlan Encapsulation To enable Vlan mode Configuring the LAN Port Configuring the LAN Port Operation ModeWith autonegotiation enabled Filling out the Bridging Table To fill out the bridge tableTo remove a MAC address from the table To configure aging timeout Configuring Aging TimeoutConfiguring QoS Mapping To configure Vlan Priority QoS Mapping Setting the LAN Rate Information to be transmitted to the DSL lineTo set the LAN rate Setting the LAN Rate in a Multiplexer Unit Configuring AutonegotiationTo set autonegotiation To set the fault indication Configuring ASMi-52 System ParametersConfiguring Fault Indication To access the Configuration menu 16. Configuration Menu To display the System Configuration menu Configuring Local Card Mode To configure local card mode To configure remote card mode Configuring Remote Card ModeConfiguring Low Speed Operation To enable the low speed operation To configure the control port data rate Configuring Control Port ParametersTo access the Control port menu Changing the Control Port Data Rate Selecting the CTS State Configuring the Terminal PortSelecting the Control Port Interface Selecting the DSR State Configuring the Port Control Mode Currently, the connection to ASMi-52 via Slip is disabledTo access the Terminal menu To change the user name and password To enable or disable the pop-up alarms To configure the security timeout To change the dial-out parameters Setting the G.704 Interface Type To set the G.704 interface type Configuring the Physical Ports To change the transmission mode To configure the use of the power backoff Configuring the Power BackoffConfiguring the Snext Margin To configure the Snext margin Configuring the Current Margin To configure the current margin Configuring the Power Spectral Density Configuring Line ProbingSetting the Loop Attenuation Threshold To access the Shdsl Repeater menu Setting the SNR Margin ThresholdConfiguring the Shdsl Repeater To set the SNR margin threshold Configuring the DTE Interface Data Rate Configuring the Data Rate in a Multiplexer UnitTo select the data rate Configuring the E1 Interface To access the E1 Port Configuration menu Selecting E1 Framing Mode To select E1 framing mode Enabling CRC-4 Code Generation Setting the Sync ModeTo enable CRC-4 code generation To select resynchronization time To define an idle code Defining Idle CodeMapping E1 Timeslots To assign E1 timeslots You can configure timeslot 0 to be looped or transparent Mapping E1 Timeslots in a Multiplexer UnitOpposite remote units with a serial data interface Matching Remote Unit Settings With Local Unit Settings To map E1 timeslots in a multiplexer unit with E1 + LAN Configuring the T1 Interface To match remote unit settings with local unit settings To access the T1 Configuration menu 37. T1 Port Configuration Displaying the ASMi-52 Status To access the Monitoring menuAdditional Tasks Displaying the System Status Alarms are described in Chapter Displaying the Port StatusTo display the port status information To access the remote ASMi-52 Entering the User Name and PasswordAccessing the Remote ASMi-52 To close a virtual terminal ASMi-52 responds to your entry with asterisks Type in your password at the prompt up to eight charactersType in your user name and press Tab Press Enter Displaying the ASMi-52 Inventory To display the ASMi-52 inventory Installing a New Software Release via Tftp To install a new software release via TftpUpdating Software Releases Displaying the following message Port Data Rate section above Autoconfiguration through Tftp or Xmodem During the software installation, the TST indicator blinksTo upload a configuration from the source device To download a configuration file to the target devices Displaying the Software VersionTo display the software version Resetting ASMi-52 Switching the Software VersionsTo swap software versions To reset ASMi-52 to the factory default Resetting to Default SettingsResetting the ASMi-52 Modem Units equipped with the management LAN port Resetting the Shdsl Repeater To reset the line interface of the Shdsl repeater 52. Repeater Reset Menu Exiting the Control Session Guidelines for Configuring ASMi-52 Units Application To enter the user name and password Configuring the ASMi-52 unitsSetting the ASMi-52 System Parameters To prepare a control session Setting the E1 Port To set the device host IP address Configuring LLB/RLB Activation from DTE Configuring the Line Interface TypeConfiguring the Serial DTE Interface To configure the line interface type for ASMi-52 units DTE Local Port Menu Page Displaying the Current Shdsl Statistics Monitoring PerformanceDisplaying Shdsl Statistics To display the current Shdsl statistics Shdsl Port Performances Menu To display the Shdsl statistics fo r all intervals Displaying the Shdsl Statistics for all IntervalsShdsl Statistics Parameters Display Description Displaying E1/T1 Statistics CRC-4 Enabled E1, ESF framing T1CRC-4 Disabled E1, SF framing T1 Clearing the Shdsl Performance Statistics Displaying the Current E1/T1 Statistics ChapterTo display the current E1/T1 statistics Display Description Range E1 Statistics Parameters TimerDisplaying E1/T1 Statistics for All Intervals To display E1/T1 statistics for all intervals Power-Up Self-Test Detecting ErrorsHandling Alarms Front Panel LEDs Displaying All Alarms To display all alarms To display the system log file Working with the System Log FileDisplaying the Port Status To clear the system log file ASMi-52 Alarms and Warnings Masking Port AlarmsTo mask ASMi-52 alarms Number Terminal Message Port Description Severity T1 Signal Loss E1 BPV ERR EXC DTE CRC Error Over ShdslT1-TS not Rate Comp E1 Signal Loss DTE Losw Failure Over Shdsl Ratio T1 Excesive ERR AIS Occured DTE Wire Mode not ShdslExcesive ERR DTE T1 AIS Occured AIS and Sync DTE External to DTE Customer SideLine Paramers not Shdsl Internal Clock ASMi-52 Events TroubleshootingWorking with the Port Log File To display the log file Testing ASMi-52 To clear the log file Bit Error Rate Test Bert Bert Patterns To configure the Bert results 16. Bert Menu Running Loopback Tests Loopback in Multiplexer Units Running the Local Loopback 20. Loopback with Multiplexer Units 22. Diagnostics Menu To run the local loopback Running the Remote Loopback Running Remote Loopback at a RepeaterTo activate the remote loopback Deactivating the Loopbacks To activate the remote loopback at the Shdsl repeaterTo deactivate a running loopback To deactivate multiple loopbacks Frequently Asked QuestionsRunning the LEDs Test To run the LEDs test Technical Support Page DTE Interface Connectors 35, X.21 and RS-530 Interface ConnectorsTable A-1. V.35, X.21 and RS-530 Connector Pinouts 35, X.21 and RS-530 Connector Pinouts Description Function 34-Pin DB-25 DB-15 Circuit E1 and T1 Interface Connector Ethernet Connector Table A-5. Control Connector Signal Direction Control ConnectorTable A-4. Control Connector Pinout Cross cable with two male DB-9 connectors Alarm Relay Connector Table A-6. Cross Cable PinoutDB-9 Pin Page Appendix B IR-IP Interface Module Overview Standard Conforms to Ieee Data Rate RJ-45 shielded 8-pin connectorOperation Mode Full duplex or half duplex user-selectable Interface Type Table B-1 RJ-45 Pinout IR-IP DIP SwitchTable B-2. IR-IP DIP Switch Functions This appendix Indications during Normal Service Power-Up Indications for Unconfigured IP Router CardPower-Up Indications for Configured IP Router Card Table B-3. IR-IP Interface Indicators Accessing the IR-IP Management Subsystem IR-IP Management Subsystem Outline of Preliminary Configuration Performing Preliminary ConfigurationDefault IP Communication Parameters To perform the preliminary configuration procedure Assigning the Router LAN Interface Address Connecting the Telnet HostPreliminary Telnet Host Configuration IP Learning Mechanism To view and edit the ARP table contents To configure the IP router LAN addressAssigning a LAN IP Address to a New IR-IP Documentation to find how to select a proper font General Operating ProceduresChanging the LAN IP Address of a Configured IR-IP IR-IP Management Utility Starting a Management Utility Menu Structure of Management Utility Quick Setup Guide To perform quick setup Operation with Default Gateway Default GatewayOperation without Default Gateway Parameters Reading Protocol from DIP Switches Figure B-7. Selecting the IP Subnet Mask Setting Telnet Inactivity Timeout Defining Management AccessDefining a Telnet Password To access the Management Access menu Advanced Setup Defining the Device IdentificationDefining the Interface Parameters Figure B-10. Interface Parameters Menu Defining the WAN Protocol Parameters Frame Relay ProtocolTo define the Frame Relay protocol parameters PPP Protocol Menu To define the PPP Protocol Parameters Defining the Multicast Parameters To define the Multicast Parameters Using the Device Control Menu To access the Static Groups menuTo access the Device Control menu Viewing the Error Log Downloading New SoftwareTo download new software Reset LAN Erasing ConfigurationResetting IR-IP To reset the LAN interface Viewing IR-IP configuration Data Viewing Configuration and ConnectionReset WAN Viewing the ARP Tables To access the ARP Tables screenTo access the multicast groups table screen Viewing the Multicast Groups Table To access the Statistics menu Viewing the Statistics Screen Using Diagnostic Tools Ping Terminal To access the Diagnostic Tools menu Using the Ping Function To ping a host Erasing IR-IP Software Erasing User’s ConfigurationTo erase the user’s configuration Desired positions, and then turn ASMi-52 on again Erasing Application Software To erase the application software IR-IP Troubleshooting What if there are no ping replies from IR-IP?What to do if the IP learning process is not successful? LCD Screen Control Port Type, 9-pin, maleEscape, Scroll Down, Scroll Right, Enter Installation Package ContentsConnecting the Interface Cable Operation Turning the Easy Config OnWorking with the Easy Config Front Panel Controls Choosing Options Accessing the ASMi-52 MenusScrolling the ASMi-52 Menus Entering Alphanumeric Values Hold down the z button, until s is displayed in the top row Assigning Timeslots Turning the Easy Config OffTo turn the Easy Config off To assign timeslots Index Bert Default settings IR-IP LLB/RLB Log file Logging out Loopback Router LAN interface address, B-7 Screen Tftp Xmodem Index ASMi-52 Ver Supplement Front PanelPage Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters