Connecting AC Power, Connecting DC Power | RAD Data comm ASMi-52


Chapter 2 Installation and Setup		Installation and Operation Manual


	Before connecting this unit to a power source and connecting or disconnecting
	any other cable, the protective earth terminals of this unit must be connected
	to the protective ground conductor of the mains (AC or DC) power cord. If you
Warning	are using an extension cord (power cable) make sure it is grounded as well.
	Any interruption of the protective (grounding) conductor (inside or outside the

instrument) or disconnecting of the protective earth terminal can make this unit dangerous. Intentional interruption is prohibited.

Connecting AC Power

AC power should be supplied through the 1.5m (5 ft) standard power cable terminated by a standard 3-prong plug. The cable is provided with the unit.

To connect AC power:

1.Connect the power cable to the power connector on the ASMi-52 rear panel.

2.Connect the power cable to the mains outlet.

The unit turns on automatically upon connection to the mains.

Connecting DC Power

DC power is supplied to ASMi-52 via a compatible AC/DC plug for attaching DC power supply lines.

To connect DC power:

•Refer to the DC power supply connection supplement.

2-4

Connecting the Power Cables

ASMi-52 Ver. 2.5

Image 36

RAD Data comm ASMi-52 manual Connecting AC Power, Connecting DC Power, To connect AC power, To connect DC power

Contents

ASMi-52 Page ASMi-52 Limited Warranty General Safety Instructions Please observe the following precautions General Safety Practices Connection of AC MainsConnection of DC Mains Ports Safety Status TNV-2TNV-3 Isdn Electromagnetic Compatibility EMC Canadian Emission Requirements Safety Supplementary Information Installing ASMi-52 Configuring ASMi-52Connecting the Interfaces Connecting the Power Configuring the Master Clock Configuring the Shdsl InterfaceConfiguring the DTE Interface Configuring the Serial Interface Configuring the T1 Interface Configuring the 10/100BaseT InterfaceTo configure E1 parameters To configure the T1 parameters Quick Start Guide Configuring ASMi-52 ASMi-52 Ver Contents Configuring a Typical Application Troubleshooting and Diagnostics Overview VersionsDTE Interface Line Interface Applications Unit Enclosure ASMi-52 Modems Operating opposite ASMi-52CD Cards Features Data Rate WireFunctionality Typical Ranges 26 AWG DTE Interface ASMi-52 Data Rates Low Speed Mode ASMi-52 Data RatesSum for all the interfaces Multiplexer Applications DTE+LAN Timing Serial DTE = V.35, X.21, RS-530, IR-IP Diagnostics Management Alarm Reporting Physical DescriptionFunctional Description Statistics Collection ASMi-52 modem consists of the following major modules Technical Specifications Diagnostics Loopbacks PWR green Power Test red Power ConsumptionSynchronization of DSL line Height Environment Introduction Technical Specifications ASMi-52 Ver To install ASMi-52 IntroductionSite Requirements and Prerequisites Package Contents Connecting the Interface Cables Connecting the Power Cables Connecting the LineConnecting the DTE Interface Connecting the Alarm Relay Connector Connecting AC Power Connecting DC PowerTo connect AC power To connect DC power Controls and Indicators Turning On ASMi-52To turn on ASMi-52 ASMi-52 Front Panel, E1 Interface 2 Wire ASMi-52 Indicator Status Normal IndicationsASMi-52 Front Panel LEDs ASMi-52 Rear Panel LEDs Default Settings Default SettingsParameter Default Value System LAN Configuration Parameter Default Value Control Port DCECTS =RTS DSR OFF Configuration Alternatives Parameter Default Value Serial DTE InterfaceE1/E1+Ethernet/E1+Serial DTE Interface T1 Interface Control Port Interface Characteristics Managing ASMi-52 via a Terminal PortPreparing the Terminal Data Terminal Ready DTR Navigating the Management Menus Correcting EntriesNavigating Data Forms To choose an option To start the ConfiguRAD session Managing ASMi-52 via Ethernet PortManaging ASMi-52 via a Dedicated Timeslot To prepare ASMi-52 for network management Managing ASMi-52 via Web Browser Managing ASMi-52 via LAN Port and a Dedicated Timeslot Configuration Menus 10. Inventory and Configuration Menus 11. Monitoring, Diagnostics and File Utilities Menus Turning Off ASMi-52 Logging OutTo end the current session To turn off ASMi-52 Configuring ASMi-52 for Management Configuring Management ParametersTo access the Management menu MTU means Maximum Transfer Unit Entering Device Information To enter device informationTo clear system parameters Type Y to confirm the deletion Configuring the Host Parameters Configuring the Network ManagersTo configure the network managers To define the IP parameters Controlling the Management Access To define the management access method Configuring Dedicated Timeslots To configure dedicated timeslots Configuring Vlan Encapsulation To enable Vlan mode Configuring the LAN Port Configuring the LAN Port Operation ModeWith autonegotiation enabled Filling out the Bridging Table To fill out the bridge tableTo remove a MAC address from the table Configuring Aging Timeout Configuring QoS MappingTo configure aging timeout To configure Vlan Priority QoS Mapping Setting the LAN Rate Information to be transmitted to the DSL lineTo set the LAN rate Setting the LAN Rate in a Multiplexer Unit Configuring AutonegotiationTo set autonegotiation Configuring ASMi-52 System Parameters Configuring Fault IndicationTo set the fault indication To access the Configuration menu 16. Configuration Menu To display the System Configuration menu Configuring Local Card Mode To configure local card mode Configuring Remote Card Mode Configuring Low Speed OperationTo configure remote card mode To enable the low speed operation Configuring Control Port Parameters To access the Control port menuTo configure the control port data rate Changing the Control Port Data Rate Configuring the Terminal Port Selecting the Control Port InterfaceSelecting the CTS State Selecting the DSR State Configuring the Port Control Mode Currently, the connection to ASMi-52 via Slip is disabledTo access the Terminal menu To change the user name and password To enable or disable the pop-up alarms To configure the security timeout To change the dial-out parameters Setting the G.704 Interface Type To set the G.704 interface type Configuring the Physical Ports To change the transmission mode Configuring the Power Backoff Configuring the Snext MarginTo configure the use of the power backoff To configure the Snext margin Configuring the Current Margin To configure the current margin Configuring the Power Spectral Density Configuring Line ProbingSetting the Loop Attenuation Threshold Setting the SNR Margin Threshold Configuring the Shdsl RepeaterTo access the Shdsl Repeater menu To set the SNR margin threshold Configuring the DTE Interface Data Rate Configuring the Data Rate in a Multiplexer UnitTo select the data rate Configuring the E1 Interface To access the E1 Port Configuration menu Selecting E1 Framing Mode To select E1 framing mode Setting the Sync Mode To enable CRC-4 code generationEnabling CRC-4 Code Generation To select resynchronization time Defining Idle Code Mapping E1 TimeslotsTo define an idle code To assign E1 timeslots You can configure timeslot 0 to be looped or transparent Mapping E1 Timeslots in a Multiplexer UnitOpposite remote units with a serial data interface Matching Remote Unit Settings With Local Unit Settings To map E1 timeslots in a multiplexer unit with E1 + LAN Configuring the T1 Interface To match remote unit settings with local unit settings To access the T1 Configuration menu 37. T1 Port Configuration To access the Monitoring menu Additional TasksDisplaying the ASMi-52 Status Displaying the System Status Alarms are described in Chapter Displaying the Port StatusTo display the port status information Entering the User Name and Password Accessing the Remote ASMi-52To access the remote ASMi-52 To close a virtual terminal Type in your password at the prompt up to eight characters Type in your user name and press TabASMi-52 responds to your entry with asterisks Press Enter Displaying the ASMi-52 Inventory To display the ASMi-52 inventory Installing a New Software Release via Tftp To install a new software release via TftpUpdating Software Releases Displaying the following message Port Data Rate section above Autoconfiguration through Tftp or Xmodem During the software installation, the TST indicator blinksTo upload a configuration from the source device To download a configuration file to the target devices Displaying the Software VersionTo display the software version Resetting ASMi-52 Switching the Software VersionsTo swap software versions Resetting to Default Settings Resetting the ASMi-52 ModemTo reset ASMi-52 to the factory default Units equipped with the management LAN port Resetting the Shdsl Repeater To reset the line interface of the Shdsl repeater 52. Repeater Reset Menu Exiting the Control Session Guidelines for Configuring ASMi-52 Units Application Configuring the ASMi-52 units Setting the ASMi-52 System ParametersTo enter the user name and password To prepare a control session Setting the E1 Port To set the device host IP address Configuring the Line Interface Type Configuring the Serial DTE InterfaceConfiguring LLB/RLB Activation from DTE To configure the line interface type for ASMi-52 units DTE Local Port Menu Page Monitoring Performance Displaying Shdsl StatisticsDisplaying the Current Shdsl Statistics To display the current Shdsl statistics Shdsl Port Performances Menu Displaying the Shdsl Statistics for all Intervals Shdsl Statistics ParametersTo display the Shdsl statistics fo r all intervals Display Description CRC-4 Enabled E1, ESF framing T1 CRC-4 Disabled E1, SF framing T1Displaying E1/T1 Statistics Clearing the Shdsl Performance Statistics Displaying the Current E1/T1 Statistics ChapterTo display the current E1/T1 statistics Display Description Range Timer Displaying E1/T1 Statistics for All IntervalsE1 Statistics Parameters To display E1/T1 statistics for all intervals Detecting Errors Handling AlarmsPower-Up Self-Test Front Panel LEDs Displaying All Alarms To display all alarms Working with the System Log File Displaying the Port StatusTo display the system log file To clear the system log file Masking Port Alarms To mask ASMi-52 alarmsASMi-52 Alarms and Warnings Number Terminal Message Port Description Severity CRC Error Over Shdsl T1-TS not Rate Comp E1 Signal Loss DTET1 Signal Loss E1 BPV ERR EXC DTE Losw Failure Over Shdsl Wire Mode not Shdsl Excesive ERR DTERatio T1 Excesive ERR AIS Occured DTE T1 AIS Occured AIS and Sync DTE Customer Side Line Paramers not ShdslExternal to DTE Internal Clock Troubleshooting Working with the Port Log FileASMi-52 Events To display the log file Testing ASMi-52 To clear the log file Bit Error Rate Test Bert Bert Patterns To configure the Bert results 16. Bert Menu Running Loopback Tests Loopback in Multiplexer Units Running the Local Loopback 20. Loopback with Multiplexer Units 22. Diagnostics Menu To run the local loopback Running the Remote Loopback Running Remote Loopback at a RepeaterTo activate the remote loopback Deactivating the Loopbacks To activate the remote loopback at the Shdsl repeaterTo deactivate a running loopback Frequently Asked Questions Running the LEDs TestTo deactivate multiple loopbacks To run the LEDs test Technical Support Page DTE Interface Connectors 35, X.21 and RS-530 Interface ConnectorsTable A-1. V.35, X.21 and RS-530 Connector Pinouts 35, X.21 and RS-530 Connector Pinouts Description Function 34-Pin DB-25 DB-15 Circuit E1 and T1 Interface Connector Ethernet Connector Control Connector Table A-4. Control Connector PinoutTable A-5. Control Connector Signal Direction Cross cable with two male DB-9 connectors Alarm Relay Connector Table A-6. Cross Cable PinoutDB-9 Pin Page Appendix B IR-IP Interface Module Overview RJ-45 shielded 8-pin connector Operation Mode Full duplex or half duplex user-selectableStandard Conforms to Ieee Data Rate Interface Type IR-IP DIP Switch Table B-2. IR-IP DIP Switch FunctionsTable B-1 RJ-45 Pinout This appendix Power-Up Indications for Unconfigured IP Router Card Power-Up Indications for Configured IP Router CardIndications during Normal Service Table B-3. IR-IP Interface Indicators Accessing the IR-IP Management Subsystem IR-IP Management Subsystem Performing Preliminary Configuration Default IP Communication ParametersOutline of Preliminary Configuration To perform the preliminary configuration procedure Connecting the Telnet Host Preliminary Telnet Host ConfigurationAssigning the Router LAN Interface Address IP Learning Mechanism To view and edit the ARP table contents To configure the IP router LAN addressAssigning a LAN IP Address to a New IR-IP General Operating Procedures Changing the LAN IP Address of a Configured IR-IPDocumentation to find how to select a proper font IR-IP Management Utility Starting a Management Utility Menu Structure of Management Utility Quick Setup Guide To perform quick setup Default Gateway Operation without Default GatewayOperation with Default Gateway Parameters Reading Protocol from DIP Switches Figure B-7. Selecting the IP Subnet Mask Defining Management Access Defining a Telnet PasswordSetting Telnet Inactivity Timeout To access the Management Access menu Advanced Setup Defining the Device IdentificationDefining the Interface Parameters Figure B-10. Interface Parameters Menu Defining the WAN Protocol Parameters Frame Relay ProtocolTo define the Frame Relay protocol parameters PPP Protocol Menu To define the PPP Protocol Parameters Defining the Multicast Parameters To define the Multicast Parameters Using the Device Control Menu To access the Static Groups menuTo access the Device Control menu Viewing the Error Log Downloading New SoftwareTo download new software Erasing Configuration Resetting IR-IPReset LAN To reset the LAN interface Viewing IR-IP configuration Data Viewing Configuration and ConnectionReset WAN To access the ARP Tables screen To access the multicast groups table screenViewing the ARP Tables Viewing the Multicast Groups Table To access the Statistics menu Viewing the Statistics Screen Using Diagnostic Tools Ping Terminal To access the Diagnostic Tools menu Using the Ping Function To ping a host Erasing User’s Configuration To erase the user’s configurationErasing IR-IP Software Desired positions, and then turn ASMi-52 on again Erasing Application Software To erase the application software IR-IP Troubleshooting What if there are no ping replies from IR-IP?What to do if the IP learning process is not successful? LCD Screen Control Port Type, 9-pin, maleEscape, Scroll Down, Scroll Right, Enter Installation Package ContentsConnecting the Interface Cable Turning the Easy Config On Working with the Easy ConfigOperation Front Panel Controls Accessing the ASMi-52 Menus Scrolling the ASMi-52 MenusChoosing Options Entering Alphanumeric Values Hold down the z button, until s is displayed in the top row Turning the Easy Config Off To turn the Easy Config offAssigning Timeslots To assign timeslots Index Bert Default settings IR-IP LLB/RLB Log file Logging out Loopback Router LAN interface address, B-7 Screen Tftp Xmodem Index ASMi-52 Ver Supplement Front PanelPage Customer Response Form Excellent Good Fair Poor Very PoorPage Error Report Page Page International Headquarters