Error & Status Messages on the Control Panel

Messages/Second messages

Description

Solution

 

 

 

 

 

 

 

 

Hardware Problem NV-RAM

The printer identified a Mem-

Replace the User Account En-

 

 

 

ory Switch (User Account En-

hance Unit.

 

 

 

hance Unit) error.

 

 

 

 

 

 

 

 

 

Hardware Problem Option

The printer identified an op-

Remove and re-install the op-

 

 

RAM

tional RAM error.

tional RAM.

 

 

 

 

 

If the message appears again,

 

 

 

 

 

contact your sales or service

 

 

 

 

 

representative.

 

 

 

 

 

 

 

 

Hardware Problem Parallel

There is a problem with the

If you use the parallel I/F, re-

 

 

I/F

parallel interface.

place the interface cable that

 

 

 

 

 

caused the error. If the mes-

 

 

 

 

 

sage appears again, contact

 

 

 

 

 

your sales or service repre-

 

 

 

 

 

sentative.

 

4

 

 

 

 

 

 

 

 

 

 

 

Hardware Problem Staple

There is misfeed in the finish-

Remove the misfeed. If the

 

 

Unit

er or there is a problem with

message appears again, con-

 

 

 

the staple unit failure.

tact your sales or service rep-

 

 

 

 

 

resentative.

 

 

 

 

 

See p.94 “When "Remove Mis-

 

 

 

 

 

feed R: Finisher" Appears”.

 

 

 

 

 

See p.98 “Removing Jammed

 

 

 

 

 

Staples”.

 

 

 

 

 

 

 

 

Hardware Problem Tray 1

There is a problem with the

Turn the power switch off and

 

 

 

paper lift motor of the Tray 1.

then on. If the message ap-

 

 

 

 

 

pears again, contact your sales

 

 

 

 

 

or service representative.

 

 

 

 

 

 

 

 

Hardware Problem Tray 2

There is a problem with the

Turn the power switch off and

 

 

 

paper lift motor of the Tray 2.

then on. If the message ap-

 

 

 

 

 

pears again, contact your sales

 

 

 

 

 

or service representative.

 

 

 

 

 

 

 

 

Hardware Problem Tray 3

There is a problem with the

Align paper and set them in

 

 

 

paper lift motor of the paper

the collect position in the pa-

 

 

 

tray 3.

per tray 3.

 

 

 

 

 

 

 

 

 

 

 

Turn the power switch off and

 

 

 

 

 

then on. If the message ap-

 

 

 

 

 

pears again, contact your sales

 

 

 

 

 

or service representative.

 

 

 

 

 

 

 

Hardware Problem Tray 4

There is a problem with the

Turn the power switch off and

 

 

 

paper lift motor of the paper

then on. If the message ap-

 

 

 

tray 4.

pears again, contact your sales

 

 

 

 

 

or service representative.

 

 

 

 

 

 

 

 

73

Page 82 Page 84
Page 83
Image 83
Ricoh AP3800C operating instructions Ram
Page 82 Page 84
Top Page Image Contents