Test Sheet Samples | Ricoh AP3800C instruction

Adjusting the Color Registration

Test Sheet Samples

Following images are samples for the test sheet.

❖ColorRegistSheet

2

❖Fuser Adjust Sheet I

41

Image 51

Ricoh AP3800C operating instructions Test Sheet Samples, ColorRegistSheet Fuser Adjust Sheet

Contents

Operating Instructions Maintenance Guide Introduction Trademarks Safety During Operation Safety Information Iii Energy Star Program Low-power Mode Energy Saver mode Specifications Symbols How to Read This Manual Table of Contents 105 100102 103 Viii Detaching the SR770 2 Tray Finisher Replacing Consumables and Maintenance Kit Opening and Closing the Duplex Reversal Unit Push up the lock release button and keep it in placeLower the Duplex Reversal Unit slowly until it stops Add Toner Replacing the Toner Cartridge Shake the toner cartridge back and forth 5-6 times Loading Toner Pull out the left cover of the print- er slowly Turn off the power switch and unplug the power cableReplacing the Fuser Oil Unit Replace Fuser Oil Unit TypeG Do not touch any areas other than the handle ZDJH055J Plug in the power cable and turn on the power switch Take out the green screwdriver Replacing the Photoconductor UnitReplace Black PCU Type F Replace Color PCU Type a Remove the Photoconductor Unit you want to replace Lift the inner cover until it clicks into place and holds Take the unit out from the bag Install a new Photoconductor Unit Tighten two screws using provid- ed screwdriver Lower the inner cover slowlyTurn the light brown lever clock- wise Calibrating Replacing the Development Unit Replace Black Dev. UnitTypeDReplace Color Dev. UnitTypeB Remove the Development Unit Install a new Development Unit ZDJH227E Please Wait Replacing the Fusing Unit Replace Fusing Unit Type CPull out the left cover of the print- er Remove the Fuser Oil Unit in the direction of the arrow Please Wait Press # for Fuser Adjust Initializing Please WaitSet Sheet Bypass, then # Ready Invalid Value Press #C D E F G H 0 0 0 0 0 0 0 Wear the glove on either hand Replacing the Dustproof Filter Attach the small filter Replace Waste Toner Type E Replacing the Waste Toner Bottle Push it in until it stops Replacing the Paper Feed Rollers Paper Feed Roller aPaper Feed Roller B Paper Feed Roller C Two Stoppers Replacing the Paper Feed Rollers ZERH090E Cleaning and Adjusting the Printer Close the right cover by pushing the area labeled Push Cleaning the Registration Roller Cleaning the DustProof Glass Auto Adjust Adjusting the Color Registration Completed Fuser AdjustColor Regist Fuser Adjust When replacing the fusing unit Test Sheet Print Cannot Adjust See User’s GuideFuser Adjust At Unit Replace Invalid Value Cannot Adjust Menu Maintenance Fuser Adjust Custom Adjust When color shifting occursLoad A4L or larger paper in the Bypass Tray Custom Adjust Plain 600dpi Select ActionSet Sheet, then# A3 297 X Press U or T to display Man- ual Adjust, and then press En Manual AdjustAdjustment a -7.0 +7.0 +0 Color Regist Manual Adjust Adjustment a -7.0 +7.0 +2 Manual Adjust Print Result Color Regist Manual AdjustPrinting Test Sheet Samples ColorRegistSheet Fuser Adjust Sheet Fuser Adjust Sheet Image Density Black Adjusting the Image DensityMaintenance Image Density Menu Maintenance Ready Prt. Test Sheet Adjusting the Registration of the TraysMaintenance Registration Registration Press U or T to set the digit of the registration value mm Registration AdjustmentAdjustment Vert. Tray Vert. Tray 3 -5.0 +5.0 Cleaning and Adjusting the Printer Paper and Other Media Supported by This Printer Paper SizesInput Paper Sizes Metric version Paper and Other Media Input Paper Sizes Inch version Output Paper Sizes Metric version Paper weight and number of sheets to be set 148 ⋅ 210 ⋅ Output Paper Sizes Inch version Paper Recommendations Loading PaperStoring Paper OHP transparencies Types of Paper and Other MediaPlain Paper Thick Paper Only envelopes a and B as shown below are supported Envelopes Paper not supported by this printer Printable Area Load paper into the tray with the print side down Loading PaperLoading Paper in Tray Pull out the paper tray slowly un- til it stops Loading Paper in Tray 2 and the Optional Paper Feed Unit Set the paper guide lock to the unlocked positionLoad paper in the same direction ZDJY007J Press U or T to display Paper Input, and then press Enter Menu Paper InputPaper Input Tray Paper Size Push in the Paper Tray slowly un- til it stops 2 x Tray 2 *AutoPress U or T to display pAuto, and then press Enter Menu Paper Input Ready Changing the paper typePaper Type Tray Tray Recycled Paper Load Paper in the Bypass Tray Press U or T to Paper In- put menu, and then press En- ter Adjust the side guides to the pa- per widthPaper Input Bypass Size Bypass Size *11 x Specifying a custom paper size for the Bypass Tray Bypass Size Custom SizeCustom Size Vert mm Custom Size Horiz mm Paper Type Bypass Tray Specifying a paper type for the Bypass TrayPress U or T to display By- pass Tray, and then press Enter Bypass Tray Thick Paper Following message appears onPanel display Error & Status Messages on the Control Panel Status MessagesAlert Messages Troubleshooting Error & Status Messages on the Control Panel UTILITY\1394 RAM Troubleshooting Error & Status Messages on the Control Panel Troubleshooting PCU Troubleshooting Error & Status Messages on the Control Panel Troubleshooting Printer Does Not Print Possible Cause Solutions Is the number of printers connected Terface cable Network Connection Status Possible Causes, Descriptions, and Solutions Other Printing Problems Der the Image Adjustments tab in the Change Use Settings Select KBlack for Gray Reproduction under the Image Status Possible Causes, Descriptions, and Solutions Detaching the 2 Tray Finisher Removing Misfed Paper Opening and Closing the Duplex Reversal Unit Removing Misfed Paper in the Duplex Feed Unit ZDJP221J ZDJP056J Open the right cover When Remove Misfeed AInternal Path Appears Back until it clicks into place B Pull out the upper left cover for the printer slowly Fold it along the printer body When Remove Misfeed W Mailbox AppearsClose the Mailbox Cover Fold the Output Tray Raise it vertically ZDJY208J Close the Lower Right cover for the Paper Feed Unit Close the front cover for the 2 Tray FinisherReturn the Output Tray back into place Raise the tray Lower it slowly If you cannot remove the paper, proceed to step C Remove the jammed staples Removing Jammed StaplesAdd Staples Open the face plate of the car- tridge to unlock it Close the front cover for the 24 Tray Finisher Pull the case cover up Adding Staples Pull out the ribbon used for bun- dling the staples Close the front cover for the 2 4 Tray Finisher Removing Punch-hole Chips Punch-hole ChipsAre Full When the Front Cover Does Not Close Close Front CoverPush in the Transfer Unit until it stops 104 Be sure to check the following points Moving and Transporting the PrinterMoving the Printer Moving the printer in the short distance 106 Consumables Toner cartridgeStaple Cartridge Name Consumables Average printable number Pages *1 Other consumables Index 110 Memo 112 Page Overseas Affiliates