Error & Status Messages on the Control Panel | Ricoh AP3800C

Error & Status Messages on the Control Panel

Messages/Second messages	Description	Solution

Reset Toner Cyan	The indicated toner cartridge	Set the indicated toner car-
	is not set correctly.	tridge(s) correctly.
		See "Setting Up" in the Setup
		Guide.

Reset Toner Magenta	The indicated toner cartridge	Set the indicated toner car-
	is not set correctly.	tridge(s) correctly.
		See "Setting Up" in the Setup
		Guide.

Reset Toner Yellow	The indicated toner cartridge	Set the indicated toner car-
	is not set correctly.	tridge(s) correctly.
		See "Setting Up" in the Setup
		Guide.

Reset Transfer Unit Correctly	The transfer unit is not set cor-	Contact your sales or service		4
	rectly, or is not set.	representative.

Reset Tray 1 Correctly	The indicated paper input	Set the indicated paper input
	tray is not set correctly, or is	tray correctly.
	not set.

Reset Tray Correctly	The printer detected, when	Set the indicated paper input
	processing a job through Auto	tray correctly.
	Tray Select, that any of paper
	input tray is not set correctly,
	or is not set.

Reset Waste Toner Correctly	The waste toner bottle is not	Set the waste toner bottle cor-
	set correctly, or is not set.	rectly.

Reset Yellow Toner Correctly	The toner cartridge (Y) is not	Set the toner cartridge (Y) cor-
	set correctly or is not set, and	rectly.
	the color printing is non-ap-	See "Setting Up" in the Setup
	plicable.	See "Setting Up" in the Setup
	plicable.	Guide.
		Guide.

RPCS Graphic Error	The graphic is not initialized	Replace the installed memory.
	because the graphic memory
	was not reserved.

RPCS Memory Overflow	The printer memory is not ini-	Replace the installed memory.
	tialized because the CDC
	memory was not reserved via
	the system call.

RPCS Syntax Error	The printer identified a syntax	Be sure to use the correct driv-
	error. This error results from;	er.
	data transmogrification
	caused by the transmission
	path problem, data interrup-
	tion, data transmission from
	other drivers, etc.

79

Image 89

Ricoh AP3800C operating instructions Error & Status Messages on the Control Panel

Contents

Operating Instructions Maintenance Guide Introduction Trademarks Safety During Operation Safety Information Iii Energy Star Program Low-power Mode Energy Saver mode Specifications Symbols How to Read This Manual Table of Contents 102 100103 105 Viii Detaching the SR770 2 Tray Finisher Replacing Consumables and Maintenance Kit Lower the Duplex Reversal Unit slowly until it stops Opening and Closing the Duplex Reversal UnitPush up the lock release button and keep it in place Add Toner Replacing the Toner Cartridge Shake the toner cartridge back and forth 5-6 times Loading Toner Replacing the Fuser Oil Unit Turn off the power switch and unplug the power cableReplace Fuser Oil Unit TypeG Pull out the left cover of the print- er slowly Do not touch any areas other than the handle ZDJH055J Plug in the power cable and turn on the power switch Replace Black PCU Type F Replacing the Photoconductor UnitReplace Color PCU Type a Take out the green screwdriver Remove the Photoconductor Unit you want to replace Lift the inner cover until it clicks into place and holds Take the unit out from the bag Install a new Photoconductor Unit Turn the light brown lever clock- wise Tighten two screws using provid- ed screwdriverLower the inner cover slowly Calibrating Replace Color Dev. UnitTypeB Replacing the Development UnitReplace Black Dev. UnitTypeD Remove the Development Unit Install a new Development Unit ZDJH227E Please Wait Pull out the left cover of the print- er Replacing the Fusing UnitReplace Fusing Unit Type C Remove the Fuser Oil Unit in the direction of the arrow Please Wait Set Sheet Bypass, then # Press # for Fuser AdjustInitializing Please Wait C D E F G H 0 0 0 0 0 0 0 ReadyInvalid Value Press # Wear the glove on either hand Replacing the Dustproof Filter Attach the small filter Replace Waste Toner Type E Replacing the Waste Toner Bottle Push it in until it stops Paper Feed Roller B Paper Feed Roller C Two Stoppers Replacing the Paper Feed RollersPaper Feed Roller a Replacing the Paper Feed Rollers ZERH090E Cleaning and Adjusting the Printer Close the right cover by pushing the area labeled Push Cleaning the Registration Roller Cleaning the DustProof Glass Auto Adjust Adjusting the Color Registration Color Regist Fuser Adjust Fuser AdjustWhen replacing the fusing unit Completed Fuser Adjust At Unit Replace Cannot Adjust See User’s GuideInvalid Value Cannot Adjust Test Sheet Print Load A4L or larger paper in the Bypass Tray Menu Maintenance Fuser Adjust Custom AdjustWhen color shifting occurs Set Sheet, then# A3 297 X Custom Adjust Plain 600dpiSelect Action Adjustment a -7.0 +7.0 +0 Manual AdjustColor Regist Manual Adjust Adjustment a -7.0 +7.0 +2 Press U or T to display Man- ual Adjust, and then press En Printing Manual Adjust Print ResultColor Regist Manual Adjust Test Sheet Samples ColorRegistSheet Fuser Adjust Sheet Fuser Adjust Sheet Maintenance Image Density Adjusting the Image DensityMenu Maintenance Ready Image Density Black Maintenance Registration Adjusting the Registration of the TraysRegistration Prt. Test Sheet Adjustment Vert. Tray Registration AdjustmentVert. Tray 3 -5.0 +5.0 Press U or T to set the digit of the registration value mm Cleaning and Adjusting the Printer Input Paper Sizes Metric version Paper and Other Media Supported by This PrinterPaper Sizes Paper and Other Media Input Paper Sizes Inch version Output Paper Sizes Metric version Paper weight and number of sheets to be set 148 ⋅ 210 ⋅ Output Paper Sizes Inch version Storing Paper Paper RecommendationsLoading Paper Plain Paper Types of Paper and Other MediaThick Paper OHP transparencies Only envelopes a and B as shown below are supported Envelopes Paper not supported by this printer Printable Area Loading Paper in Tray Loading PaperPull out the paper tray slowly un- til it stops Load paper into the tray with the print side down Load paper in the same direction Loading Paper in Tray 2 and the Optional Paper Feed UnitSet the paper guide lock to the unlocked position ZDJY007J Paper Input Tray Paper Size Menu Paper InputPush in the Paper Tray slowly un- til it stops Press U or T to display Paper Input, and then press Enter Press U or T to display pAuto, and then press Enter 2 xTray 2 *Auto Paper Type Tray Changing the paper typeTray Recycled Paper Menu Paper Input Ready Load Paper in the Bypass Tray Paper Input Bypass Size Adjust the side guides to the pa- per widthBypass Size *11 x Press U or T to Paper In- put menu, and then press En- ter Custom Size Vert mm Bypass Size Custom SizeCustom Size Horiz mm Specifying a custom paper size for the Bypass Tray Press U or T to display By- pass Tray, and then press Enter Paper Type Bypass TraySpecifying a paper type for the Bypass Tray Panel display Bypass Tray Thick PaperFollowing message appears on Alert Messages Error & Status Messages on the Control PanelStatus Messages Troubleshooting Error & Status Messages on the Control Panel UTILITY\1394 RAM Troubleshooting Error & Status Messages on the Control Panel Troubleshooting PCU Troubleshooting Error & Status Messages on the Control Panel Troubleshooting Printer Does Not Print Possible Cause Solutions Is the number of printers connected Terface cable Network Connection Status Possible Causes, Descriptions, and Solutions Other Printing Problems Der the Image Adjustments tab in the Change Use Settings Select KBlack for Gray Reproduction under the Image Status Possible Causes, Descriptions, and Solutions Detaching the 2 Tray Finisher Removing Misfed Paper Opening and Closing the Duplex Reversal Unit Removing Misfed Paper in the Duplex Feed Unit ZDJP221J ZDJP056J Open the right cover When Remove Misfeed AInternal Path Appears Back until it clicks into place B Pull out the upper left cover for the printer slowly Close the Mailbox Cover When Remove Misfeed W Mailbox AppearsFold the Output Tray Raise it vertically Fold it along the printer body ZDJY208J Return the Output Tray back into place Raise the tray Close the front cover for the 2 Tray FinisherLower it slowly Close the Lower Right cover for the Paper Feed Unit If you cannot remove the paper, proceed to step C Add Staples Removing Jammed StaplesOpen the face plate of the car- tridge to unlock it Remove the jammed staples Close the front cover for the 24 Tray Finisher Pull the case cover up Adding Staples Pull out the ribbon used for bun- dling the staples Close the front cover for the 2 4 Tray Finisher Are Full Removing Punch-hole ChipsPunch-hole Chips Push in the Transfer Unit until it stops When the Front Cover Does Not CloseClose Front Cover 104 Moving the Printer Moving and Transporting the PrinterMoving the printer in the short distance Be sure to check the following points 106 Staple Cartridge ConsumablesToner cartridge Name Consumables Average printable number Pages *1 Other consumables Index 110 Memo 112 Page Overseas Affiliates