SATO GT424 manual General Specifications CONT’D, Model Name

Section 1:		Introduction
1.1 GENERAL SPECIFICATIONS (CONT’D)
	Specification/
				GT408	GT412	GT424
	Model Name
	Print method				Thermal transfer or thermal
	Head density			8 dots/ mm (203 dpi)	12 dots/ mm (305 dpi)	24 dots/ mm (609 dpi)
	Print valid range (width)			104 mm x pitch 2500 mm	104 mm x pitch 1500 mm	104 mm x pitch 400 mm
				Not printable for 3 mm from the backside.
	Print speed (Max)			12 inches/sec	12 inches/sec	6 inches/sec
				(Approx 300mm/sec)	(Approx 300 mm/sec)	(Approx 150mm/sec)
				Note:
				Maximum speed may be further dependent on the type of print layout, paper,
				or carbon ribbon in use.
	Paper Thickness			0.060 mm to 0.268 mm supported.
				Note:
				Be sure to use only printer supplies manufactured or certified by SATO.
	Label size		Standard	Width: 22 to 128 mm (25 to 131 mm)		Note:
				Pitch: 5 to 397 mm (9 to 400 mm)		Supported sizes may be
	(mounting					regulated due to the quan-
			Tear off	Width: 22 to 128 mm (25 to 131 mm)
	and					tity of print jobs or size of
	cardboard			Pitch: 17 to 397 mm (20 to 400 mm)		paper.
	size)
			Peel	Width: 22 to 128 mm (25 to 131 mm)		Other usage conditions
				Pitch: 17 to 397 mm (20 to 400 mm)
						may restrict the range of
			Cutter	Width: 22 to 128 mm (25 to 131 mm)		label sizes supported.
				Pitch: 17 to 397 mm (20 to 400 mm)
			Non-sepa-	Width: 22 to 128 mm (25 to 131 mm)
			rate	Pitch: 17 to 397 mm (20 to 400 mm)
	Number of		Roll paper	Maximum external diameter:
	loadable			200 mm (Approximately 150 m/roll) 3-inch paper tube used
	sheets			Back winding (only front winding for non-separate mode)
			Fanfold	Maximum folded height: 200 mm
			paper	See the section in this manual on Setting Fanfold Paper
	Carbon ribbon			Be sure to use the specified carbon ribbon manufactured by SATO.
	Width			39.5, 45, 59, 76, 84, 92, 102, 111, and 128 mm
	Length			Use a carbon ribbon that is wider than the paper used.
	Thickness of base material			300 m/roll
	Color			4.5 µm
	Winding direction			Black (standard), also red, blue, purple, and green
				Front winding and back winding
	Label dispensing modes			Continuous, tear off, peeler, dispenser and non-separate
	Dimensions			W 271 mm x D 455 mm x H 305 mm x (Standard)
	Weight			14 kg (for a standard configuration)
	Power supply			Input voltage: AC 100 V to 240 V ±10%
				Power consumption: Maximum 200 VA 150 W, print rate 30% (89 VA 40 W on standby)
	Operating Environment			Operational ambient temperature: 0 to 40 ×C
				Operational ambient humidity: 30 to 80% (without condensation)
				Storing ambient temperature: -5 to 60 ×C
				Storing ambient humidity: 30 to 90% (no condensation)
				Paper, and carbon ribbon excluded.

Page 1-4 GT Series Operator’s Manual