VME A24 Control Register | Spectrum Brands C6x VME64 guide

Spectrum Signal Processing	Monaco Technical Reference
	Registers

VME A24 Control Register

VME A24 Secondary Base Address + 1004h

D31..		..D8

Reserved

D7..	..D1	D0

Reserved		/Reset

The VME host uses this register to reset all Monaco board devices except for the SCV64 bus interface chip.

∙To reset the board, the VME host writes a “0” to bit D0.

This read/write register is accessed from the VME A24 bus. It is located at offset 1004h from the base address set by jumper JP1 (A23..A17).

Part Number 500-00191	57
Revision 2.00

Image 69

Spectrum Brands C6x VME64 manual VME A24 Control Register

Contents

Monaco Revision Iii Preface Document Rev Date Changes ChangeHistory Table of Contents Monaco Technical Reference Vii Viii List of Figures Table of Contents List of Tables Xii Features IntroductionProduct Operation Processors VME InterfacesPMC PEM Reference Documents General Bus Architecture On-Board Power Supply VME A24 Slave Interface Reset Reset ConditionsJtag Reset Sysreset Board Layout Board Layout Jumper settings Jumper Settings DescriptionOUT Part Number Processor Nodes Processor Configurations Populated Processor Node Block Diagram Processor Memory Configuration Internal MemoryExternal Memory 0x0180 DSP Memory Map Nodes B, C, and D Address Synchronous Dram Synchronous Burst SramProcessor Expansion Module Host Port Processor Boot Source Jumpers Node Processor Booting Serial Port Routing Serial Port Routing VME and PMC Connections for Serial Port PEM Connections for Serial Port 0 Global Shared Bus Global Shared Bus Access Source TargetMemory Arbitration Burst Cycle Bus Access Single Cycle Bus Access Locked Cycles Global Shared Bus VME64 Bus Interface VME OperationSCV64 Primary Slave A32/A24 Interface A24 Secondary Slave Interface Access A24 Secondary Interface Memory Map Hpia HPI Register Addresses VME address Master A32/A24/A16 SCV64 Interface VME64 Bus Interface DSP~LINK3 Data Transfer Operating Modes DSP~LINK3 Interface Astrben Address Strobe Control Mode DSP~LINK3 Reset Interface Signals DSP~LINK3 Interface Hurricane Configuration PCI InterfacePCI Offset Address Value Initialize Hurricane Register Set BCC2A PCI Device Hurricane Implementation Jtag Chain Jtag Debugging Jtag Debugging Overview Interrupt Handling Interrupt Routing DSP~LINK3 Interrupts to Node a PCI Bus Interrupts PEM InterruptsHurricane Interrupt SCV64 Interrupt KIPL2 KIPL1 KIPL0 Kipl Status Bits and the Iack Cycle Bit Node Whose Access Caused the Bus Error Bus Error Interrupts VME Host Interrupts To Any Node Inter-processor Interrupts Registers Register Address Summary Access Privilege Bus KFC2..0 KSIZE1..0 KADDR1..0 Vpage Register Vstatus Register Buserra KavecKIPL2..0 Vinta Register Vintb Register Vintc Register Vintd Register Kiplend Kipl Enable RegisterKiplenc Kiplenb DSP~LINK3 Register DL3RESET ID Register Hinta VME A24 Status RegisterHintb Hintc VME A24 Control Register Registers Board Identification SpecificationsMonaco Monaco67 General Specifications Parameter Performance and Data Throughput Data Access/Transfer Performance Specifications Connector Layout Connector Pinouts VME P1 Connector Pinout VME Connectors VME P2 Connector Pinout PMC to VME P2 VME P2 Connector DSP~LINK3 to VME P2 PMC Connector JN1 Pinout PMC Connectors PMC Connector JN2 PMC Connector JN4 Non-standard PMC Connector JN5 PEM 1 Connector Pinout PEM Connectors PEM 2 Connector Pinout Jtag Connectors Jtag in Connector PinoutJtag OUT Connector Connector Pinouts SCV64 Register Initialization Appendix a SCV64 Register Values SCV64 Register Initialization VME Index Interrupts to node A, 40 register Reset Jtag Sysreset