Vintb Register | Spectrum Brands C6x VME64 specification

Monaco Technical Reference

Spectrum Signal Processing

Registers

VINTB Register

Address: 016D 8008h

D31..		..D8

Reserved

D7..	..D1	D0

Reserved		Interrupt

This register allows any processor to generate or clear an interrupt to node B. Upon reset this value is ‘0’.

∙To generate an interrupt to node B, set bit D0 of this register to “1”.

∙To clear an interrupt to node B, set bit D0 of this register to “0”.

50	Part Number 500-00191
	Revision 2.00

Image 62

Spectrum Brands C6x VME64 manual Vintb Register

Contents

Monaco Revision Preface Iii History Document Rev Date ChangesChange Table of Contents Monaco Technical Reference Vii Viii List of Figures Table of Contents List of Tables Xii Product Operation Processors FeaturesIntroduction PMC InterfacesVME PEM Reference Documents On-Board Power Supply General Bus Architecture Jtag Reset Reset ConditionsVME A24 Slave Interface Reset Sysreset Board Layout Board Layout OUT Jumper settingsJumper Settings Description Part Number Processor Configurations Populated Processor Nodes Processor Node Block Diagram External Memory Processor Memory ConfigurationInternal Memory 0x0180 DSP Memory Map Address Nodes B, C, and D Processor Expansion Module Synchronous Burst SramSynchronous Dram Host Port Processor Booting Processor Boot Source Jumpers Node Serial Port Routing Serial Port Routing PEM Connections for Serial Port 0 VME and PMC Connections for Serial Port Memory Global Shared Bus Access Source TargetGlobal Shared Bus Arbitration Single Cycle Bus Access Burst Cycle Bus Access Locked Cycles Global Shared Bus SCV64 Primary Slave A32/A24 Interface VME64 Bus InterfaceVME Operation Access A24 Secondary Slave Interface A24 Secondary Interface Memory Map HPI Register Addresses VME address Hpia Master A32/A24/A16 SCV64 Interface VME64 Bus Interface DSP~LINK3 Interface DSP~LINK3 Data Transfer Operating Modes Address Strobe Control Mode Astrben Interface Signals DSP~LINK3 Reset DSP~LINK3 Interface PCI Offset Address Hurricane ConfigurationPCI Interface Hurricane Register Set Value Initialize BCC2A Hurricane Implementation PCI Device Jtag Debugging Jtag Chain Jtag Debugging Interrupt Handling Overview DSP~LINK3 Interrupts to Node a Interrupt Routing Hurricane Interrupt PEM InterruptsPCI Bus Interrupts SCV64 Interrupt Kipl Status Bits and the Iack Cycle KIPL2 KIPL1 KIPL0 Bus Error Interrupts Bit Node Whose Access Caused the Bus Error Inter-processor Interrupts VME Host Interrupts To Any Node Register Address Summary Access Privilege Bus Registers Vpage Register KFC2..0 KSIZE1..0 KADDR1..0 Vstatus Register KIPL2..0 BuserraKavec Vinta Register Vintb Register Vintc Register Vintd Register Kiplenc Kipl Enable RegisterKiplend Kiplenb DL3RESET DSP~LINK3 Register ID Register Hintb VME A24 Status RegisterHinta Hintc VME A24 Control Register Registers Monaco SpecificationsBoard Identification Monaco67 Specifications Parameter General Data Access/Transfer Performance Performance and Data Throughput Specifications Connector Pinouts Connector Layout VME Connectors VME P1 Connector Pinout VME P2 Connector Pinout PMC to VME P2 VME P2 Connector DSP~LINK3 to VME P2 PMC Connectors PMC Connector JN1 Pinout PMC Connector JN2 PMC Connector JN4 Non-standard PMC Connector JN5 PEM Connectors PEM 1 Connector Pinout PEM 2 Connector Pinout Jtag OUT Connector Jtag ConnectorsJtag in Connector Pinout Connector Pinouts Appendix a SCV64 Register Values SCV64 Register Initialization SCV64 Register Initialization Index VME Interrupts to node A, 40 register Reset Jtag Sysreset