Specification s, Parameter Specification | Teledyne 651 manual

Product Overview

Teledyne API Ultrafine Particle Monitor - Model 651

Figure 1-1

Ultrafine Particle Monitor - Model 651

S p e c i f i c a t i o n s

Table 1-1 contains the operating specifications for the Model 651 instrument. These specifications are subject to change without notice.

Table 1-1 Model 651 Specifications

PARAMETER		SPECIFICATION
Particle Size Range
Min detectable particle (D50)		7 nm (verified with DMA-classified sucrose)
Max detectable particle		3 μm
Particle Concentration Range
Single Particle Counting		0 to 106 particles/cm3, with continuous live-time
		coincidence correction
Particle Concentration Accuracy
Measurement Accuracy		±10% at 106 particles/cm3
Response Time (T95)
High flow mode(3 L/min)		<3 sec to 95% in response to concentration step
		change
Low flow mode (0.6 L/min)		<5 sec to 95% in response to concentration step
		change
Flow
High-flow inlet		3 ±0.3 L/min
Low-flow inlet		0.6 ± 0.06 L/min

18	07506C DCN6727

Image 20

Teledyne 651 operation manual Specification s, Parameter Specification

Contents

Model Page Trademarks This page intentionally left blank F e t y M e s s a g e s Laser Safety R N I N G R r a n t y This page intentionally left blank O u t T h i s M a n u a l V i s i o n H i s t o r y Viii Contents Particle Counting Maintenance, Service, and Troubleshooting G u r e s SFC Set Flow Rate Calibration Constant B l e s Table A-1 Xiv G a n i z a t i o n How This Manual is OrganizedR p o s e L a t e d P r o d u c t L i t e r a t u r e T t i n g H e l p A P T E R Product OverviewO d u c t D e s c r i p t i o n Specification s Parameter Specification Parameter Water System Physical Features W i t W o r k s 2illustrates the flow system of the Model Model 651 Flow System Schematic Unpacking and Setting Up the Model C k i n g L i s t Model 651 Maintenance Kit PN DU0000169 P a c k i n g Installation Connecting the Water SupplyEquipment Remove Protective Caps Bracket Screw Connecting the Water Supply Connecting the Water Exhaust Tube Connecting the Aerosol Supply Connecting the Aerosol Supply Nozzle Securing Inlet Screen Assembly in Place Installing the Model 651 in a Rack Connecting the USB Cable Connecting Power and Warming up the Model Warm-up Screen Preparing the Model 651 for Shipping and Storage Moving and Shipping ModelMoving the Model 651 Short Distances 07506C DCN6727 Display Instrument DescriptionO n t P a n e l Indicator Light Status Messages C k P a n e l Vacuum Supply T e r n a l I n s t r u m e n t C o m p o n e n t sOptics Module Water System FansCircuit Boards Internal Clock Data Communication Ports RS-232 Serial Connections Ethernet Communication Port 07506C DCN6727 Outdoor Operation Procedures Instrument OperationE r a t i n g P r e c a u t i o n s C o m m e n d e d O p e r a t i o n P r o c e d u r e s Standard Operation Procedures ∙ Status ∙ Setup ∙ Total R m u pS p l a y / U s e r S e t t i n g s Home Screen Status Description Setup Screens OFF On AfterWarmup SET Time Address Total Screen Mask 07506C DCN6727 Technical Description E o r y S i g n o f t h e M o d e l 6 5 Sensor Pulse Height Flow System Critical Flow Temperature Control Inlet Pressure Measurement Water Removal System Page 07506C DCN6727 Particle Counting T a l C o u n t a c c u r a c y V e T i m e C o u n t i n g Concentration = Total counts N c e n t r a t i o n M e a s u r e m e n t Concentration = N × t 07506C DCN6727 T a l i z e r M o d e 07506C DCN6727 Ethernet Computer Interface Commands, and Data CollectionM p u t e r I n t e r f a c e Programs and Features Choose Turn Windows features on or off Flash Drives Flash Memory Data Files Line Example of data record USB RS-232 Serial Communications Terminal Communications Communications Parameters SET M m a n d sRead 07506C DCN6727 07506C DCN6727 Maintenance, Service Troubleshooting U t i o n M o v i n g t h e C o v e r P l a c e m e n t P a r t s K i t s M o v i n g a n d Install i n g t h e W i c k T e A n g i n g t h e F i l t e r s R o s o l F l o w C h e c k s Model 651 Flow Schematic E a n i n g t h e W a t e r B o t t l e S p e c t i n g a n d C l e a n i n g t h e F a n s E a n / R e p l a c e t h e O r i f i c e s S p e c t L i q u i d L i n e s A t u s M e s s a g e s Troubleshooting Troubleshooting INLET/DRAIN C h n i c a l a s s i s t a n c e T u r n i n g t h e M o d e l 6 5 1 f o r S e r v i c e Primer on Electro Static Discharge W S t a t i c C h a r g e s a r e C r e a t e d Static Generation Voltages for Typical Activities Sensitivity of Electronic Devices to Damage by ESD M m o n M y t h s a b o u t E S D D a m a g e S i c P r i n c i p l e s o f S t a t i c C o n t r o l General Rules 07506C DCN6727 Working at the Instrument Rack Working at an Anti-ESD Work Bench Opening Shipments from Teledyne API’S Customer Service Transferring Components from Rack to Bench and Back Packing Components for Return to TAPI’s Customer Service 100 07506C DCN6727 Commands Read SET Command Explanation Read Commands RAI A D C o m m a n d sRAI Read Analog Input Voltage Rall Read Operating Condition Rall RCT RCT Read Current TimeRD Read Displayed Concentration RIE Read Instrument Errors RIF Read Aerosol Flow RateRIE RIF RIS RIS Read Instrument StatusRL Read Laser Current RLL Read Liquid Level RPA Read Absolute Pressure TransducerRPN Read Nozzle Pressure Transducer RPV Read Vacuum Pressure RRD Read Data Record RRD RTA Read Cabinet Temperature RTC Read Conditioner TemperatureRRS Read Status Record RRS RV Read Firmware Version Number RTG Read Growth Tube TemperatureRTO Read Optics Temperature SM Set Mode T C o m m a n d s SFC SA Set Auxiliary Flow ValveSFC Set Flow Rate Calibration Constant SP Set Pump Vacuum SR Set Real-time Clock Sstart Starts a New Sample Sstart T a R e p o r t i n g R e c o r d s ST Set Transport Flow Pstd RecordCNT Record Status Tinlet Index Aerosol inlet 43, 45 External vacuum source Orifice Teledyne Contact Information Index-5