Computer Interface Commands, and Data Collection | Teledyne 651

C H A P T E R 8

Computer Interface,

Commands, and Data

Collection

This chapter provides information about the computer interface, communications information, and data collection for the Ultrafine Particle Monitor - Model 651. Information about using a Flash Drive is also provided.

C o m p u t e r I n t e r f a c e

The Model 651 provides four interfaces to allow for flexible data collection and instrument control. This section of the manual includes information about the following data interfaces:

∙Ethernet

∙Flash Drive

∙USB

∙RS-232 (Serial)

Although four interfaces are provided, you can only use one at a time. The Serial and USB data interfaces share a common communications channel to the Model 651 microcontroller. Data input to the Model 651 from the Serial interface is exclusive from input via the USB interface. Communications can be received from the Serial interface until a connection is linked to the USB port. When the link is established, communications can be received via the USB port but not from the Serial port. When the USB link is terminated, the Serial port can be used.

Ethernet

The Ethernet port on the Model 651 can provide system status information or instrument control over a network. In the instructions below, the client is used. Please note that Telnet feature is not included with Windows Vista® or Windows 7 operating system and must it must be enabled to be used.

07506C DCN6727

67

Image 69

Teledyne 651 operation manual Computer Interface Commands, and Data Collection, M p u t e r I n t e r f a c e, Ethernet

Contents

Model Page Trademarks This page intentionally left blank F e t y M e s s a g e s R N I N G Laser Safety R r a n t y This page intentionally left blank V i s i o n H i s t o r y O u t T h i s M a n u a l Viii Contents Particle Counting Maintenance, Service, and Troubleshooting SFC Set Flow Rate Calibration Constant G u r e s Table A-1 B l e s Xiv How This Manual is Organized R p o s eG a n i z a t i o n T t i n g H e l p L a t e d P r o d u c t L i t e r a t u r e Product Overview O d u c t D e s c r i p t i o nA P T E R Parameter Specification Specification s Water System Parameter W i t W o r k s Physical Features 2illustrates the flow system of the Model Model 651 Flow System Schematic C k i n g L i s t Unpacking and Setting Up the Model P a c k i n g Model 651 Maintenance Kit PN DU0000169 Connecting the Water Supply InstallationEquipment Remove Protective Caps Bracket Screw Connecting the Water Supply Connecting the Aerosol Supply Connecting the Water Exhaust Tube Connecting the Aerosol Supply Nozzle Securing Inlet Screen Assembly in Place Installing the Model 651 in a Rack Connecting Power and Warming up the Model Connecting the USB Cable Warm-up Screen Moving and Shipping Model Moving the Model 651 Short DistancesPreparing the Model 651 for Shipping and Storage 07506C DCN6727 Instrument Description O n t P a n e lDisplay Status Messages Indicator Light C k P a n e l T e r n a l I n s t r u m e n t C o m p o n e n t s Optics ModuleVacuum Supply Fans Water SystemCircuit Boards Internal Clock RS-232 Serial Connections Data Communication Ports Ethernet Communication Port 07506C DCN6727 Instrument Operation Outdoor Operation ProceduresE r a t i n g P r e c a u t i o n s C o m m e n d e d O p e r a t i o n P r o c e d u r e s Standard Operation Procedures R m u p ∙ Status ∙ Setup ∙ TotalS p l a y / U s e r S e t t i n g s Home Screen Status Description Setup Screens On After WarmupOFF SET Time Address Mask Total Screen 07506C DCN6727 E o r y Technical Description Sensor S i g n o f t h e M o d e l 6 5 Pulse Height Critical Flow Flow System Inlet Pressure Measurement Temperature Control Water Removal System Page 07506C DCN6727 T a l C o u n t a c c u r a c y Particle Counting Concentration = Total counts V e T i m e C o u n t i n g Concentration = N × t N c e n t r a t i o n M e a s u r e m e n t 07506C DCN6727 T a l i z e r M o d e 07506C DCN6727 Computer Interface Commands, and Data Collection M p u t e r I n t e r f a c eEthernet Programs and Features Choose Turn Windows features on or off Flash Drives Line Flash Memory Data Files Example of data record RS-232 Serial Communications USB Communications Parameters Terminal Communications M m a n d s ReadSET 07506C DCN6727 07506C DCN6727 U t i o n Maintenance, Service Troubleshooting P l a c e m e n t P a r t s K i t s M o v i n g t h e C o v e r M o v i n g a n d Install i n g t h e W i c k T e A n g i n g t h e F i l t e r s R o s o l F l o w C h e c k s Model 651 Flow Schematic E a n i n g t h e W a t e r B o t t l e E a n / R e p l a c e t h e O r i f i c e s S p e c t i n g a n d C l e a n i n g t h e F a n s S p e c t L i q u i d L i n e s A t u s M e s s a g e s Troubleshooting Troubleshooting INLET/DRAIN T u r n i n g t h e M o d e l 6 5 1 f o r S e r v i c e C h n i c a l a s s i s t a n c e W S t a t i c C h a r g e s a r e C r e a t e d Primer on Electro Static Discharge Static Generation Voltages for Typical Activities Sensitivity of Electronic Devices to Damage by ESD M m o n M y t h s a b o u t E S D D a m a g e General Rules S i c P r i n c i p l e s o f S t a t i c C o n t r o l 07506C DCN6727 Working at an Anti-ESD Work Bench Working at the Instrument Rack Transferring Components from Rack to Bench and Back Opening Shipments from Teledyne API’S Customer Service Packing Components for Return to TAPI’s Customer Service 100 07506C DCN6727 Read SET Commands Command Explanation Read Commands A D C o m m a n d s RAI Read Analog Input VoltageRAI Rall Rall Read Operating Condition RCT Read Current Time RD Read Displayed ConcentrationRCT RIF Read Aerosol Flow Rate RIE Read Instrument ErrorsRIE RIF RIS Read Instrument Status RL Read Laser CurrentRIS RPA Read Absolute Pressure Transducer RLL Read Liquid LevelRPN Read Nozzle Pressure Transducer RPV Read Vacuum Pressure RRD RRD Read Data Record RTC Read Conditioner Temperature RTA Read Cabinet TemperatureRRS Read Status Record RRS RTG Read Growth Tube Temperature RTO Read Optics TemperatureRV Read Firmware Version Number T C o m m a n d s SM Set Mode SA Set Auxiliary Flow Valve SFC Set Flow Rate Calibration ConstantSFC SR Set Real-time Clock SP Set Pump Vacuum Sstart Sstart Starts a New Sample ST Set Transport Flow T a R e p o r t i n g R e c o r d s Record CNTPstd Tinlet Record Status Aerosol inlet 43, 45 Index External vacuum source Orifice Teledyne Contact Information Index-5