Moving and Shipping Model | Teledyne 651 manual

C H A P T E R 3

Moving and Shipping

the Model 651

Use the information in this chapter to prepare the Ultrafine Particle

Monitor - Model 651 for moving or shipping.

Caution- Prevent Damage and Avoid Invalidating the Warranty. The Model 651 operates using water as a working fluid. Do not tip the instrument more than 10 degrees during normal operation or you may flood the optical system.

Do not:

∙Ship an “undried” instrument.

∙Transport an “undried” instrument over long distances.

∙Subject an “undried” instrument to freezing temperatures.

Any of the above actions can result in the flooding of the optical system, performance degradation, and possible damage to the instrument. Such neglect is not covered under the manufacturer’s warranty.

Moving the Model 651 Short Distances

You can successfully transport the Model 651 short distances from one lab to another, or even a short drive in a vehicle, without draining it first. However, do not tip the instrument >45°and do not subject it to prolonged freezing temperatures.

Preparing the Model 651 for Shipping and Storage

To prepare the Model 651 for shipping, follow these instructions:

1.Disconnect the water bottle, empty it, and then reconnect it.

2.If you have not already done so, turn on the particle monitor and allow it to warm up (the display screen reads Ready when the warm-up is complete and all the settings are correct).

3.Disconnect any connections to the aerosol inlet.

4.Allow the instrument to operate for at least one hour with the water source disconnected.

5.Disconnect the drain tube from the WATER EXHAUST outlet.

6.Turn off the power.

07506C DCN6727

33

Image 35

Teledyne operation manual Moving and Shipping Model, Moving the Model 651 Short Distances

Contents

Model Page Trademarks This page intentionally left blank F e t y M e s s a g e s R N I N G Laser Safety R r a n t y This page intentionally left blank V i s i o n H i s t o r y O u t T h i s M a n u a l Viii Contents Particle Counting Maintenance, Service, and Troubleshooting SFC Set Flow Rate Calibration Constant G u r e s Table A-1 B l e s Xiv G a n i z a t i o n How This Manual is OrganizedR p o s e T t i n g H e l p L a t e d P r o d u c t L i t e r a t u r e A P T E R Product OverviewO d u c t D e s c r i p t i o n Parameter Specification Specification s Water System Parameter W i t W o r k s Physical Features 2illustrates the flow system of the Model Model 651 Flow System Schematic C k i n g L i s t Unpacking and Setting Up the Model P a c k i n g Model 651 Maintenance Kit PN DU0000169 Remove Protective Caps InstallationConnecting the Water Supply Equipment Bracket Screw Connecting the Water Supply Connecting the Aerosol Supply Connecting the Water Exhaust Tube Connecting the Aerosol Supply Nozzle Securing Inlet Screen Assembly in Place Installing the Model 651 in a Rack Connecting Power and Warming up the Model Connecting the USB Cable Warm-up Screen Preparing the Model 651 for Shipping and Storage Moving and Shipping ModelMoving the Model 651 Short Distances 07506C DCN6727 Display Instrument DescriptionO n t P a n e l Status Messages Indicator Light C k P a n e l Vacuum Supply T e r n a l I n s t r u m e n t C o m p o n e n t sOptics Module Internal Clock Water SystemFans Circuit Boards RS-232 Serial Connections Data Communication Ports Ethernet Communication Port 07506C DCN6727 C o m m e n d e d O p e r a t i o n P r o c e d u r e s Outdoor Operation ProceduresInstrument Operation E r a t i n g P r e c a u t i o n s Standard Operation Procedures Home Screen ∙ Status ∙ Setup ∙ TotalR m u p S p l a y / U s e r S e t t i n g s Status Description Setup Screens OFF On AfterWarmup SET Time Address Mask Total Screen 07506C DCN6727 E o r y Technical Description Sensor S i g n o f t h e M o d e l 6 5 Pulse Height Critical Flow Flow System Inlet Pressure Measurement Temperature Control Water Removal System Page 07506C DCN6727 T a l C o u n t a c c u r a c y Particle Counting Concentration = Total counts V e T i m e C o u n t i n g Concentration = N × t N c e n t r a t i o n M e a s u r e m e n t 07506C DCN6727 T a l i z e r M o d e 07506C DCN6727 Ethernet Computer Interface Commands, and Data CollectionM p u t e r I n t e r f a c e Programs and Features Choose Turn Windows features on or off Flash Drives Line Flash Memory Data Files Example of data record RS-232 Serial Communications USB Communications Parameters Terminal Communications SET M m a n d sRead 07506C DCN6727 07506C DCN6727 U t i o n Maintenance, Service Troubleshooting P l a c e m e n t P a r t s K i t s M o v i n g t h e C o v e r M o v i n g a n d Install i n g t h e W i c k T e A n g i n g t h e F i l t e r s R o s o l F l o w C h e c k s Model 651 Flow Schematic E a n i n g t h e W a t e r B o t t l e E a n / R e p l a c e t h e O r i f i c e s S p e c t i n g a n d C l e a n i n g t h e F a n s S p e c t L i q u i d L i n e s A t u s M e s s a g e s Troubleshooting Troubleshooting INLET/DRAIN T u r n i n g t h e M o d e l 6 5 1 f o r S e r v i c e C h n i c a l a s s i s t a n c e W S t a t i c C h a r g e s a r e C r e a t e d Primer on Electro Static Discharge Static Generation Voltages for Typical Activities Sensitivity of Electronic Devices to Damage by ESD M m o n M y t h s a b o u t E S D D a m a g e General Rules S i c P r i n c i p l e s o f S t a t i c C o n t r o l 07506C DCN6727 Working at an Anti-ESD Work Bench Working at the Instrument Rack Transferring Components from Rack to Bench and Back Opening Shipments from Teledyne API’S Customer Service Packing Components for Return to TAPI’s Customer Service 100 07506C DCN6727 Read SET Commands Command Explanation Read Commands RAI A D C o m m a n d sRAI Read Analog Input Voltage Rall Rall Read Operating Condition RCT RCT Read Current TimeRD Read Displayed Concentration RIF RIE Read Instrument ErrorsRIF Read Aerosol Flow Rate RIE RIS RIS Read Instrument StatusRL Read Laser Current RPV Read Vacuum Pressure RLL Read Liquid LevelRPA Read Absolute Pressure Transducer RPN Read Nozzle Pressure Transducer RRD RRD Read Data Record RRS RTA Read Cabinet TemperatureRTC Read Conditioner Temperature RRS Read Status Record RV Read Firmware Version Number RTG Read Growth Tube TemperatureRTO Read Optics Temperature T C o m m a n d s SM Set Mode SFC SA Set Auxiliary Flow ValveSFC Set Flow Rate Calibration Constant SR Set Real-time Clock SP Set Pump Vacuum Sstart Sstart Starts a New Sample ST Set Transport Flow T a R e p o r t i n g R e c o r d s Pstd RecordCNT Tinlet Record Status Aerosol inlet 43, 45 Index External vacuum source Orifice Teledyne Contact Information Index-5