Status Description | Teledyne 651 specs

Instrument Operation

Teledyne API Ultrafine Particle Monitor - Model 651

Press MORE on the first Status screen to see the ADDITIONAL

STATUS settings. The photos below show the STATUS and

ADDITIONAL STATUS screens.

The Status screens display the following information:

Status	Description
Concentration	Represented in particles/cm3
Pulse Height	The signal height in mV. The pulse height varies
	with particle concentration and is useful for
	indicating problems with the wick.
Optics Temp	Temperature of the Optics in degrees Celsius. A
	normal Optics temperature is 60°C.
Growth Tube Temp	Temperature of the Growth Tube in degrees
	Celsius. A normal Growth Tube temperature is
	60°C.
Conditioner Temp	Temperature of the Conditioner in degrees Celsius.
	A normal Conditioner temperature is 20°C.
Vacuum	The vacuum pressure in mbars (must be less than
	half of the inlet pressure).
Inlet Pressure	The atmospheric pressure in mbars. This
	parameter is preset and can be used to indicate a
	blockage.

46	07506C DCN6727

Image 48

Teledyne 651 operation manual Status Description

Contents

Model Page Trademarks This page intentionally left blank F e t y M e s s a g e s Laser Safety R N I N G R r a n t y This page intentionally left blank O u t T h i s M a n u a l V i s i o n H i s t o r y Viii Contents Particle Counting Maintenance, Service, and Troubleshooting G u r e s SFC Set Flow Rate Calibration Constant B l e s Table A-1 Xiv How This Manual is Organized R p o s eG a n i z a t i o n L a t e d P r o d u c t L i t e r a t u r e T t i n g H e l p Product Overview O d u c t D e s c r i p t i o nA P T E R Specification s Parameter Specification Parameter Water System Physical Features W i t W o r k s 2illustrates the flow system of the Model Model 651 Flow System Schematic Unpacking and Setting Up the Model C k i n g L i s t Model 651 Maintenance Kit PN DU0000169 P a c k i n g Installation Connecting the Water SupplyEquipment Remove Protective Caps Bracket Screw Connecting the Water Supply Connecting the Water Exhaust Tube Connecting the Aerosol Supply Connecting the Aerosol Supply Nozzle Securing Inlet Screen Assembly in Place Installing the Model 651 in a Rack Connecting the USB Cable Connecting Power and Warming up the Model Warm-up Screen Moving and Shipping Model Moving the Model 651 Short DistancesPreparing the Model 651 for Shipping and Storage 07506C DCN6727 Instrument Description O n t P a n e lDisplay Indicator Light Status Messages C k P a n e l T e r n a l I n s t r u m e n t C o m p o n e n t s Optics ModuleVacuum Supply Water System FansCircuit Boards Internal Clock Data Communication Ports RS-232 Serial Connections Ethernet Communication Port 07506C DCN6727 Outdoor Operation Procedures Instrument OperationE r a t i n g P r e c a u t i o n s C o m m e n d e d O p e r a t i o n P r o c e d u r e s Standard Operation Procedures ∙ Status ∙ Setup ∙ Total R m u pS p l a y / U s e r S e t t i n g s Home Screen Status Description Setup Screens On After WarmupOFF SET Time Address Total Screen Mask 07506C DCN6727 Technical Description E o r y S i g n o f t h e M o d e l 6 5 Sensor Pulse Height Flow System Critical Flow Temperature Control Inlet Pressure Measurement Water Removal System Page 07506C DCN6727 Particle Counting T a l C o u n t a c c u r a c y V e T i m e C o u n t i n g Concentration = Total counts N c e n t r a t i o n M e a s u r e m e n t Concentration = N × t 07506C DCN6727 T a l i z e r M o d e 07506C DCN6727 Computer Interface Commands, and Data Collection M p u t e r I n t e r f a c eEthernet Programs and Features Choose Turn Windows features on or off Flash Drives Flash Memory Data Files Line Example of data record USB RS-232 Serial Communications Terminal Communications Communications Parameters M m a n d s ReadSET 07506C DCN6727 07506C DCN6727 Maintenance, Service Troubleshooting U t i o n M o v i n g t h e C o v e r P l a c e m e n t P a r t s K i t s M o v i n g a n d Install i n g t h e W i c k T e A n g i n g t h e F i l t e r s R o s o l F l o w C h e c k s Model 651 Flow Schematic E a n i n g t h e W a t e r B o t t l e S p e c t i n g a n d C l e a n i n g t h e F a n s E a n / R e p l a c e t h e O r i f i c e s S p e c t L i q u i d L i n e s A t u s M e s s a g e s Troubleshooting Troubleshooting INLET/DRAIN C h n i c a l a s s i s t a n c e T u r n i n g t h e M o d e l 6 5 1 f o r S e r v i c e Primer on Electro Static Discharge W S t a t i c C h a r g e s a r e C r e a t e d Static Generation Voltages for Typical Activities Sensitivity of Electronic Devices to Damage by ESD M m o n M y t h s a b o u t E S D D a m a g e S i c P r i n c i p l e s o f S t a t i c C o n t r o l General Rules 07506C DCN6727 Working at the Instrument Rack Working at an Anti-ESD Work Bench Opening Shipments from Teledyne API’S Customer Service Transferring Components from Rack to Bench and Back Packing Components for Return to TAPI’s Customer Service 100 07506C DCN6727 Commands Read SET Command Explanation Read Commands A D C o m m a n d s RAI Read Analog Input VoltageRAI Rall Read Operating Condition Rall RCT Read Current Time RD Read Displayed ConcentrationRCT RIE Read Instrument Errors RIF Read Aerosol Flow RateRIE RIF RIS Read Instrument Status RL Read Laser CurrentRIS RLL Read Liquid Level RPA Read Absolute Pressure TransducerRPN Read Nozzle Pressure Transducer RPV Read Vacuum Pressure RRD Read Data Record RRD RTA Read Cabinet Temperature RTC Read Conditioner TemperatureRRS Read Status Record RRS RTG Read Growth Tube Temperature RTO Read Optics TemperatureRV Read Firmware Version Number SM Set Mode T C o m m a n d s SA Set Auxiliary Flow Valve SFC Set Flow Rate Calibration ConstantSFC SP Set Pump Vacuum SR Set Real-time Clock Sstart Starts a New Sample Sstart T a R e p o r t i n g R e c o r d s ST Set Transport Flow Record CNTPstd Record Status Tinlet Index Aerosol inlet 43, 45 External vacuum source Orifice Teledyne Contact Information Index-5