Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SA4T Serial Interface Board B-SA704-RS-QM-R, Packing List, Installation Procedure

Models: B-SA4T

1 58

Download 58 pages 37.75 Kb

Page 26

EO15-33001A

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

4. Serial Interface Board: B-SA704-RS-QM-R

4. Serial Interface Board: B-SA704-RS-QM-R

The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted.

•Packing List

The following parts are supplied with the kit. Make sure you have all items shown below.

SIO PC Board (1 pc.)

Locking Support (1 pc.)

PCB Support Plate (1 pc.)

Serial Interface Cable
SMW-3x6 Screw (3 pcs.)	Installation Manual (1 copy)

NOTE: Make sure that the Serial Interface Cable is connected to CN4 on the SIO PC Board.

•Installation Procedure

1. Remove the two screws from the back of the printer.

SMW-3x6	Side Panel

4- 1

Image 26

Toshiba B-SA4T installation manual Serial Interface Board B-SA704-RS-QM-R, Packing List, Installation Procedure, Side Panel

Contents

Document No. EO15-33001A Option Installation ManualB-SA4T SERIES Original JulTABLE OF CONTENTS Page1.1 B-SA204-QM / B-SA204-QM-R Installation Procedure1. Cutter Module Packing ListHinge Pin Hinge Pin Hole Hinge Pin 100 Front Cover Hinge ScrewCutter Module Cover Hinge Pin HoleCleaning Media loading procedureSystem mode setting Operation checkPacking List 1.2 B-SA204P-QM-RInstallation Procedure Hinge Pin Hinge Pin Hole Hinge Pin INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTCutter Module Cover Cutter UnitConnector B-3x6 Screw Ground Wire Cutter Harness Ground WireInstallation Procedure 2. Strip Module2.1 B-SA904-H-QM-R Packing ListShaft Holder Cut Cut Strip Unit Backing Paper Feed Roller 100 Front Cover HingeScrewHinge Strip Module Cover EO15-33001A 2. Strip Module6. Close the Strip Unit How to use the Guide Roller Attaching the CutterSystem Mode Settings for Stripping PET Labels INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 1. It is recommended that the print start position and strip position are adjusted on the actual print conditionINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Packing List 2.2 B-SA904P-H-QM-RInstallation Procedure EO15-33001A Revision Date Jan 19 2. Strip ModuleHinge Strip Module Cover Hinge INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT100 Front Cover HingeStopper Shaft Holder Cut Cut Strip Unit Backing Paper Feed Roller6. Close the Strip Unit NOTE Depending on the backing paper types, tearing off the backing paper against the slot of the strip module cover may cause it to wind onto the inner rollers. It is advisable to tear off or cut the backing paper outside the strip module cover How to use the Guide RollerAttaching the Cutter Installation Manual 1 copy 3. Wireless LAN Module B-SA704-WLAN-QMWireless LAN Board 1 pc Packing ListInstallation Procedure 1. Remove the two SMW-3x6 screws from the back of the printer3. Remove the two SMW-3x6 screws to detach the Blind Plate Copper foil Wireless LAN Board SMW-3x6 ScrewWireless LAN Module Print Head Cable10. Re-attach the Side Panel to the printer Country Code Table Country CodeHow to set a country code using TELNET Packing List 4. Serial Interface Board B-SA704-RS-QM-RInstallation Procedure EO15-33001A 4. Serial Interface Board B-SA704-RS-QM-RB-SA4TP INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TM 3. Remove the two screws to detach the Blind Plate5. Fit the Locking Support into the MAIN PC Board 8. Re-attach the Side Panel 9. For an operation check, settings, etc., refer to theINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT SMW-3x6 Locking Support5. 300 dpi Print Head Kit B-SA704-TPH3-QM-R Packing ListInstallation Procedure Packing List 6. Real Time Clock B-SA704-RTC-QM-RInstallation Procedure Page Battery Sticker 4. Attach the Real Time Clock to the printer with the SMW-4x8 screwB-SA4TP Model B-SA4TM ModelINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT System Setting Date and Time SettingSet the date and time using the following procedure RESTART key INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTwith the FEED or RESTART key 7. Expansion I/O Board B-SA704-IO-QM-R Packing ListB-SA4TP INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TM 3. Remove the two SMW-3x6 screws to detach the Blind Plate5. Connect the Interface Cable to CN4 on the MAIN PC Board INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 8. RFID Module B-SA704-RFID-U2-EU-RApplicable Model EO15-33001A Revision Date Feb. 25 8. RFID Module B-SA704-RFID-U2-EU-R INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTPacking List Side Panel SMW-3x6 Screw Outline of the introduction of an RFID KitInstallation Procedure B-SA4TP INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TM Screws 7. Connect the Interface Cable to CN6 on the Main PC Board. CN6 10. Attach the Cable Clamp to the position shown below Double Sems Screw M-3x6 RFID Module 12. Connect the Interface Cable to the RFID ModuleInterface Cable RFID Module RFID Module RFID Module Attaching Plate Double Sems Screw M-3x6When Short-Pitch RFID Tags 20mm are used position. Platen FEED U2 B-SA704-RFID-U2-EU-R RFID Module SettingsINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EPC C1 Gen2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT3 Default 5 Default INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT4.0 Default 2.0 Default18 Default, Strongest INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT+00 Default +99 99mm Reverse feedINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT AGC Threshold Setting INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Description of Serial Number Label Identification of The Rfid Module B-SA704-RFID-U2-EU-RDescription of Service Number Label