Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SA4T installation manual B-SA904P-H-QM-R, Packing List, Installation Procedure

Models: B-SA4T

1 58

Download 58 pages 37.75 Kb

Page 16

EO15-33001A

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

(Revision Date: Jan: 19, 2006)

2. Strip Module

2.2 B-SA904P-H-QM-R

B-SA904P-H-QM-R is an optional strip module for the B-SA4TP Series (Plastic cover).

•Packing List

Strip Unit (1 pc.)

Strip Module Cover (1 pc.)

SMW-3x6 Screw (4 pcs.)

Cutter (1 pc.)

Guide Roller (1 pc.)

Installation Manual (1 copy)

NOTE: When issuing labels in batch mode even though the strip module is fitted, please use the provided cutter to tear off the issued labels. Do not attach the cutter when labels are stripped one by one.

•Installation Procedure

1. Open the Top Cover and the Front Cover. Remove the Connector Cover.

Top Cover

Connector Cover

Front Cover

B-3x6 Screw

2- 8

Image 16

Toshiba B-SA4T B-SA904P-H-QM-R, Packing List, Installation Procedure, EO15-33001A Revision Date Jan 19 2. Strip Module

Contents

Option Installation Manual B-SA4T SERIESDocument No. EO15-33001A Original JulTABLE OF CONTENTS PageInstallation Procedure 1. Cutter Module1.1 B-SA204-QM / B-SA204-QM-R Packing List100 Front Cover Hinge Screw Cutter Module CoverHinge Pin Hinge Pin Hole Hinge Pin Hinge Pin HoleMedia loading procedure System mode settingCleaning Operation checkInstallation Procedure 1.2 B-SA204P-QM-RPacking List INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Cutter Module CoverHinge Pin Hinge Pin Hole Hinge Pin Cutter UnitConnector B-3x6 Screw Ground Wire Cutter Harness Ground Wire2. Strip Module 2.1 B-SA904-H-QM-RInstallation Procedure Packing List100 Front Cover HingeScrew Hinge Strip Module CoverShaft Holder Cut Cut Strip Unit Backing Paper Feed Roller EO15-33001A 2. Strip Module6. Close the Strip Unit How to use the Guide Roller Attaching the CutterSystem Mode Settings for Stripping PET Labels INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 1. It is recommended that the print start position and strip position are adjusted on the actual print conditionINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 2.2 B-SA904P-H-QM-R Installation ProcedurePacking List EO15-33001A Revision Date Jan 19 2. Strip ModuleINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 100 Front Cover HingeStopperHinge Strip Module Cover Hinge Shaft Holder Cut Cut Strip Unit Backing Paper Feed Roller6. Close the Strip Unit Attaching the Cutter How to use the Guide RollerNOTE Depending on the backing paper types, tearing off the backing paper against the slot of the strip module cover may cause it to wind onto the inner rollers. It is advisable to tear off or cut the backing paper outside the strip module cover 3. Wireless LAN Module B-SA704-WLAN-QM Wireless LAN Board 1 pcInstallation Manual 1 copy Packing ListInstallation Procedure 1. Remove the two SMW-3x6 screws from the back of the printer3. Remove the two SMW-3x6 screws to detach the Blind Plate Wireless LAN Board SMW-3x6 Screw Wireless LAN ModuleCopper foil Print Head Cable10. Re-attach the Side Panel to the printer How to set a country code using TELNET Country CodeCountry Code Table 4. Serial Interface Board B-SA704-RS-QM-R Installation ProcedurePacking List EO15-33001A 4. Serial Interface Board B-SA704-RS-QM-RINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT B-SA4TMB-SA4TP 3. Remove the two screws to detach the Blind Plate5. Fit the Locking Support into the MAIN PC Board 9. For an operation check, settings, etc., refer to the INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT8. Re-attach the Side Panel SMW-3x6 Locking Support5. 300 dpi Print Head Kit B-SA704-TPH3-QM-R Packing ListInstallation Procedure Installation Procedure 6. Real Time Clock B-SA704-RTC-QM-RPacking List Page Battery Sticker 4. Attach the Real Time Clock to the printer with the SMW-4x8 screwB-SA4TP Model B-SA4TM ModelSet the date and time using the following procedure System Setting Date and Time SettingINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT with the FEED or RESTART key INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTRESTART key 7. Expansion I/O Board B-SA704-IO-QM-R Packing ListINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT B-SA4TMB-SA4TP 3. Remove the two SMW-3x6 screws to detach the Blind Plate5. Connect the Interface Cable to CN4 on the MAIN PC Board Applicable Model 8. RFID Module B-SA704-RFID-U2-EU-RINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Packing List INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTEO15-33001A Revision Date Feb. 25 8. RFID Module B-SA704-RFID-U2-EU-R Installation Procedure Outline of the introduction of an RFID KitSide Panel SMW-3x6 Screw B-SA4TM INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TP Screws 7. Connect the Interface Cable to CN6 on the Main PC Board. CN6 10. Attach the Cable Clamp to the position shown below 12. Connect the Interface Cable to the RFID Module Interface Cable RFID ModuleDouble Sems Screw M-3x6 RFID Module RFID Module RFID Module Attaching Plate Double Sems Screw M-3x6When Short-Pitch RFID Tags 20mm are used position. Platen INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT RFID Module SettingsFEED U2 B-SA704-RFID-U2-EU-R 3 Default INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTEPC C1 Gen2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 4.0 Default5 Default 2.0 DefaultINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT +00 Default18 Default, Strongest +99 99mm Reverse feedINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT AGC Threshold Setting INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Description of Service Number Label Identification of The Rfid Module B-SA704-RFID-U2-EU-RDescription of Serial Number Label