Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SA4T Front Cover Hinge Screw, Cutter Module Cover, Hinge Pin Hinge Pin Hole Hinge Pin

Models: B-SA4T

1 58

Download 58 pages 37.75 Kb

Page 4

100°

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

1. Cutter Module

2.Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement.

100°

Front Cover

Hinge

Screw

3. Mount the Cutter Module Cover by inserting the hinge pins into the hinges.

Cutter Module Cover	Hinge

4. Fit the Cutter Unit to the front of the printer by inserting the Hinge Pins into the Hinge Pin Holes.

Hinge Pin

Hinge Pin Hole

Hinge Pin

Hinge Pin Hole

Cutter Unit

1- 2

Image 4

Toshiba B-SA4T Front Cover Hinge Screw, Cutter Module Cover, Hinge Pin Hinge Pin Hole Hinge Pin, Cutter Unit

Contents

Option Installation Manual B-SA4T SERIESDocument No. EO15-33001A Original JulTABLE OF CONTENTS PageInstallation Procedure 1. Cutter Module1.1 B-SA204-QM / B-SA204-QM-R Packing List100 Front Cover Hinge Screw Cutter Module CoverHinge Pin Hinge Pin Hole Hinge Pin Hinge Pin HoleMedia loading procedure System mode settingCleaning Operation checkInstallation Procedure 1.2 B-SA204P-QM-RPacking List INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Cutter Module CoverHinge Pin Hinge Pin Hole Hinge Pin Cutter UnitConnector B-3x6 Screw Ground Wire Cutter Harness Ground Wire2. Strip Module 2.1 B-SA904-H-QM-RInstallation Procedure Packing List100 Front Cover HingeScrew Hinge Strip Module CoverShaft Holder Cut Cut Strip Unit Backing Paper Feed Roller EO15-33001A 2. Strip Module6. Close the Strip Unit How to use the Guide Roller Attaching the CutterSystem Mode Settings for Stripping PET Labels INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 1. It is recommended that the print start position and strip position are adjusted on the actual print conditionINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 2.2 B-SA904P-H-QM-R Installation ProcedurePacking List EO15-33001A Revision Date Jan 19 2. Strip ModuleINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 100 Front Cover HingeStopperHinge Strip Module Cover Hinge Shaft Holder Cut Cut Strip Unit Backing Paper Feed Roller6. Close the Strip Unit Attaching the Cutter How to use the Guide RollerNOTE Depending on the backing paper types, tearing off the backing paper against the slot of the strip module cover may cause it to wind onto the inner rollers. It is advisable to tear off or cut the backing paper outside the strip module cover 3. Wireless LAN Module B-SA704-WLAN-QM Wireless LAN Board 1 pcInstallation Manual 1 copy Packing ListInstallation Procedure 1. Remove the two SMW-3x6 screws from the back of the printer3. Remove the two SMW-3x6 screws to detach the Blind Plate Wireless LAN Board SMW-3x6 Screw Wireless LAN ModuleCopper foil Print Head Cable10. Re-attach the Side Panel to the printer How to set a country code using TELNET Country CodeCountry Code Table 4. Serial Interface Board B-SA704-RS-QM-R Installation ProcedurePacking List EO15-33001A 4. Serial Interface Board B-SA704-RS-QM-RINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT B-SA4TMB-SA4TP 3. Remove the two screws to detach the Blind Plate5. Fit the Locking Support into the MAIN PC Board 9. For an operation check, settings, etc., refer to the INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT8. Re-attach the Side Panel SMW-3x6 Locking Support5. 300 dpi Print Head Kit B-SA704-TPH3-QM-R Packing ListInstallation Procedure Installation Procedure 6. Real Time Clock B-SA704-RTC-QM-RPacking List Page Battery Sticker 4. Attach the Real Time Clock to the printer with the SMW-4x8 screwB-SA4TP Model B-SA4TM ModelSet the date and time using the following procedure System Setting Date and Time SettingINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT with the FEED or RESTART key INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTRESTART key 7. Expansion I/O Board B-SA704-IO-QM-R Packing ListINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT B-SA4TMB-SA4TP 3. Remove the two SMW-3x6 screws to detach the Blind Plate5. Connect the Interface Cable to CN4 on the MAIN PC Board Applicable Model 8. RFID Module B-SA704-RFID-U2-EU-RINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Packing List INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTEO15-33001A Revision Date Feb. 25 8. RFID Module B-SA704-RFID-U2-EU-R Installation Procedure Outline of the introduction of an RFID KitSide Panel SMW-3x6 Screw B-SA4TM INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TP Screws 7. Connect the Interface Cable to CN6 on the Main PC Board. CN6 10. Attach the Cable Clamp to the position shown below 12. Connect the Interface Cable to the RFID Module Interface Cable RFID ModuleDouble Sems Screw M-3x6 RFID Module RFID Module RFID Module Attaching Plate Double Sems Screw M-3x6When Short-Pitch RFID Tags 20mm are used position. Platen INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT RFID Module SettingsFEED U2 B-SA704-RFID-U2-EU-R 3 Default INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTEPC C1 Gen2 INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 4.0 Default5 Default 2.0 DefaultINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT +00 Default18 Default, Strongest +99 99mm Reverse feedINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT AGC Threshold Setting INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Description of Service Number Label Identification of The Rfid Module B-SA704-RFID-U2-EU-RDescription of Serial Number Label