Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SA4T Installation Procedure For Optional Equipment, Cutter Module Cover, Cutter Unit

Models: B-SA4T

1 58

Download 58 pages 37.75 Kb

Page 7

Image 7

INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT

EO15-33001A

1. Cutter Module

3. Mount the Cutter Module Cover by inserting the hinge pins into the hinges.

Cutter Module Cover

Hinge

4. Fit the Cutter Unit to the front of the printer by inserting the Hinge Pins into the Hinge Pin Holes.

Hinge Pin

Hinge Pin Hole

Hinge Pin

Cutter Unit

Hinge Pin Hole

5. Close the Cutter Unit and secure it to the printer with the Set Screw.

Set Screw

Cutter Unit

1- 5

Page 7

Image 7

Toshiba B-SA4T Installation Procedure For Optional Equipment, Cutter Module Cover, Hinge Pin Hinge Pin Hole Hinge Pin

Contents

Original Jul Option Installation ManualB-SA4T SERIES Document No. EO15-33001APage TABLE OF CONTENTSPacking List Installation Procedure1. Cutter Module 1.1 B-SA204-QM / B-SA204-QM-RHinge Pin Hole 100 Front Cover Hinge ScrewCutter Module Cover Hinge Pin Hinge Pin Hole Hinge PinOperation check Media loading procedureSystem mode setting CleaningInstallation Procedure 1.2 B-SA204P-QM-RPacking List Cutter Unit INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTCutter Module Cover Hinge Pin Hinge Pin Hole Hinge PinGround Wire Connector B-3x6 Screw Ground Wire Cutter HarnessPacking List 2. Strip Module2.1 B-SA904-H-QM-R Installation ProcedureEO15-33001A 2. Strip Module 100 Front Cover HingeScrewHinge Strip Module Cover Shaft Holder Cut Cut Strip Unit Backing Paper Feed Roller6. Close the Strip Unit Attaching the Cutter How to use the Guide RollerINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT System Mode Settings for Stripping PET Labels1. It is recommended that the print start position and strip position are adjusted on the actual print condition INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A Revision Date Jan 19 2. Strip Module 2.2 B-SA904P-H-QM-RInstallation Procedure Packing ListShaft Holder Cut Cut Strip Unit Backing Paper Feed Roller INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT100 Front Cover HingeStopper Hinge Strip Module Cover Hinge6. Close the Strip Unit Attaching the Cutter How to use the Guide RollerNOTE Depending on the backing paper types, tearing off the backing paper against the slot of the strip module cover may cause it to wind onto the inner rollers. It is advisable to tear off or cut the backing paper outside the strip module cover Packing List 3. Wireless LAN Module B-SA704-WLAN-QMWireless LAN Board 1 pc Installation Manual 1 copy1. Remove the two SMW-3x6 screws from the back of the printer Installation Procedure3. Remove the two SMW-3x6 screws to detach the Blind Plate Print Head Cable Wireless LAN Board SMW-3x6 ScrewWireless LAN Module Copper foil10. Re-attach the Side Panel to the printer How to set a country code using TELNET Country CodeCountry Code Table EO15-33001A 4. Serial Interface Board B-SA704-RS-QM-R 4. Serial Interface Board B-SA704-RS-QM-RInstallation Procedure Packing List3. Remove the two screws to detach the Blind Plate INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TM B-SA4TP5. Fit the Locking Support into the MAIN PC Board SMW-3x6 Locking Support 9. For an operation check, settings, etc., refer to theINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT 8. Re-attach the Side PanelPacking List 5. 300 dpi Print Head Kit B-SA704-TPH3-QM-RInstallation Procedure Installation Procedure 6. Real Time Clock B-SA704-RTC-QM-RPacking List Page 4. Attach the Real Time Clock to the printer with the SMW-4x8 screw Battery StickerB-SA4TM Model B-SA4TP ModelSet the date and time using the following procedure System Setting Date and Time SettingINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT with the FEED or RESTART key INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTRESTART key Packing List 7. Expansion I/O Board B-SA704-IO-QM-R3. Remove the two SMW-3x6 screws to detach the Blind Plate INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TM B-SA4TP5. Connect the Interface Cable to CN4 on the MAIN PC Board Applicable Model 8. RFID Module B-SA704-RFID-U2-EU-RINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Packing List INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTEO15-33001A Revision Date Feb. 25 8. RFID Module B-SA704-RFID-U2-EU-R Installation Procedure Outline of the introduction of an RFID KitSide Panel SMW-3x6 Screw B-SA4TM INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTB-SA4TP Screws 7. Connect the Interface Cable to CN6 on the Main PC Board. CN6 10. Attach the Cable Clamp to the position shown below RFID Module RFID Module Attaching Plate Double Sems Screw M-3x6 12. Connect the Interface Cable to the RFID ModuleInterface Cable RFID Module Double Sems Screw M-3x6 RFID ModuleWhen Short-Pitch RFID Tags 20mm are used position. Platen INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT RFID Module SettingsFEED U2 B-SA704-RFID-U2-EU-R 3 Default INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENTEPC C1 Gen2 2.0 Default INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT4.0 Default 5 Default+99 99mm Reverse feed INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT+00 Default 18 Default, StrongestINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT AGC Threshold SettingINSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT Description of Service Number Label Identification of The Rfid Module B-SA704-RFID-U2-EU-RDescription of Serial Number Label