Toshiba MJ-1103, MJ-1104 Stapler home position sensor, P11-I20 7 Fig For the stapling operation

7. Sensors and switches (Finisher section : Common for MJ-1103/1104)

Symbol	Name	Function	P-I	Remarks
S1	Entrance sensor	Detects paper transported from the	P7-I23	P.2-7 "Fig. 2-7"
		junction box.
S2	Transport sensor	Detects the paper transported to the	P7-I23	P.2-7 "Fig. 2-7"
		entrance of the buffer tray.
S3	Paddle home position sensor	Detects the home position of the pad-	P5-I19	P.2-7 "Fig. 2-7"
		dle.
S4	Shutter opening/closing sen-	Detects the home position of the shut-	P5-I19	P.2-7 "Fig. 2-7"
	sor	ter.
S5	Buffer tray home position sen-	Detects that the buffer tray is at the out-	P8-I20	P.2-7 "Fig. 2-7"
	sor	ermost position.
S6	Paper holder home position	Detects the home position of the paper	P8-I20	P.2-7 "Fig. 2-7"
	sensor	holder cam.
S7	Front alignment plate home	Detects the home position of the front	P10-I17	P.2-7 "Fig. 2-7"
	position sensor	alignment plate.
S8	Rear alignment plate home	Detects the home position of the rear	P10-I17	P.2-7 "Fig. 2-7"
	position sensor	alignment plate.
S9	Stack exit belt home position	Detects the home position of the stack	P10-I52	P.2-7 "Fig. 2-7"
	sensor	exit belt.
S10	Stapler unit home position	Detects if the stapler unit is at the front	P11-I24	P.2-7 "Fig. 2-7"
	sensor	side (home position).
S11	Stapler interference sensor	Detects when the stapler unit interferes	P11-I24	P.2-7 "Fig. 2-7"
		with other mechanical section.
S12	Finishing tray paper detection	Detects the presence/absence of the	P10-I17	P.2-7 "Fig. 2-7"
	sensor	paper on the finishing tray.
S13	Movable tray position-A sen-	Detects the movable tray position.	P4-I15	P.2-7 "Fig. 2-7"
	sor
S14	Movable tray position-B sen-	Detects the movable tray position.	P4-I15	P.2-7 "Fig. 2-7"
	sor
S15	Movable tray position-C sen-	Detects the movable tray position.	P4-I15	P.2-7 "Fig. 2-7"
	sor
S16	Movable tray paper-full sen-	Detects the upper surface of paper set	P4-I15	P.2-7 "Fig. 2-7"
	sor	on the movable tray.
S17	Movable tray paper exist sen-	Detects the presence/absence of the	P4-I15	P.2-7 "Fig. 2-7"
	sor	paper on the movable tray.
S18	Stationary tray paper-full sen-	Detects the paper-full state of the sta-	P12-I2	P.2-7 "Fig. 2-7"
	sor	tionary tray.
S19	Stapler home position sensor	Detects the home position in the stapler	P11-I20	P.2-7 "Fig. 2-7"
		for the stapling operation.
S20	Staple top position sensor	Detects the staple top position in the	P11-I20	P.2-7 "Fig. 2-7"
		stapler.
S21	Staple empty sensor	Detects the empty status of staples in	P11-I20	P.2-7 "Fig. 2-7"
		the stapler cartridge.
S22	Feeding sensor	Detects paper transported from the	P15-I14/	P.2-7 "Fig. 2-7"
		main unit into the junction box.	P16-I8
S23	Movable tray shift motor sen-	Detects the rotation of the movable tray	P12-I2	P.2-7 "Fig. 2-7"
	sor	shift motor.
S25	Connection sensor	Detects that the Finisher is released	P13-I28	P.2-7 "Fig. 2-7"
		from the main unit.
SW1	Front cover switch	Cuts off the drive current (+24V) when	P15-I19/	P.2-7 "Fig. 2-7"
		the opening status of the front cover is	P16-I41
		detected.
SW2	Stationary tray opening/clos-	Detects the opening (lifting) of the sta-	-	P.2-7 "Fig. 2-7"
	ing switch	tionary tray.
SW3	Stapler interference switch	Automatically cut off the power supply	-	P.2-7 "Fig. 2-7"
		to the stapler on detecting the no-oper-
		ation area for the stapler unit.
SW4	Connection switch	Cuts off drive current (24V) when it	P13-I3	P.2-7 "Fig. 2-7"
		detects that the Finisher is released
		from the main unit.

© 2008, 2009 TOSHIBA TEC CORPORATION All rights reserved	MJ-1103/1104
	GENERAL DESCRIPTION

2

2 - 11