Manuals / Toshiba / Computer Equipment / Printer Accessories

Toshiba MJ-1104, MJ-1103 service manual ED13 Front alignment plate home position error

Models: MJ-1104 MJ-1103

1 282

Download 282 pages 43.5 Kb

Page 212

[ED13] Front alignment plate home position error

Is there any mechanical problem when the front alignment plate is moved?

 YES Fix the mechanism.

NO

Is there a disconnection of the connector, incorrect installation or breakage of the front align- ment plate home position sensor (S7)?

l	YES •	Reconnect the connector securely if there is any disconnection.
l	•	Reinstall the sensor correctly if there is any incorrect installation.

• Replace the sensor if there is any breakage.

NO

Is the harness between the front alignment plate home position sensor (S7) and the CN18 of the finisher control PC board (FIN) disconnected or open circuited?

Is the harness between the front alignment motor (M5) and the CN17 of the finisher control PC board (FIN) disconnected or open circuited?

l YES • Reconnect the connector securely if there is any disconnection.

• Replace the harness if open circuited.

NO

Replace the finisher control PC board (FIN).

[ED14] Rear alignment plate home position error

Is there any mechanical problem when the rear alignment plate is moved?

 YES Fix the mechanism.

NO

Is there a disconnection of the connector, incorrect installation or breakage of the rear alignment plate home position sensor (S8)?

l	YES •	Reconnect the connector securely if there is any disconnection.
l	•	Reinstall the sensor correctly if there is any incorrect installation.

• Replace the sensor if there is any breakage.

NO

Is the harness between the rear alignment plate home position sensor (S8) and the CN18 of the finisher control PC board (FIN) disconnected or open circuited?

Is the harness between the rear alignment motor (M6) and the CN17 of the finisher control PC board (FIN) disconnected or open circuited?

l YES • Reconnect the connector securely if there is any disconnection.

• Replace the harness if open circuited.

NO

Replace the finisher control PC board (FIN).

MJ-1103/1104	© 2008, 2009 TOSHIBA TEC CORPORATION All rights reserved
TROUBLESHOOTING

6 - 8

Image 212

Toshiba MJ-1104, MJ-1103 ED13 Front alignment plate home position error, ED14 Rear alignment plate home position error

Contents

MJ-1103/1104 Trademarks Page Page Contents Saddle Stitch Finisher stapler related error MJ-1104 Paper jam in movable tray sectionSPECIFICATIONS, Accessory and Consumables SpecificationsFinisher section Common for MJ-1103/1104 Stacking Type Facedown Stacking Height with Stationary TrayPaper Size HeightPaper Size A4, B5, LT, 8.5SQ, 16K A3, A4-R, B4, FOLIO, LD, LG, LT-R Saddle stitch section MJ-1104 Thick paper cover included64 80g/m 2 Paper 81 90g/m 2 Paper 91 105g/m 2 Paper 91 105g/m2 PaperMJ-1103 MJ-1104 AccessoryConsumables General Description Main ComponentsSectional View UnitsGate solenoid Finisher section B-1 Front side viewPaper exit guide clutch Rear side view Saddle section C-1 Front side view M16 M17 M14Transport roller Paper holding damperElectric Parts Layout SOL2 M10 CLT2 M12 M2 M13S19 S20Motors Saddle section MJ-1104 Symbols and Functions of Various ComponentsSymbol Name Function Remarks Solenoids Saddle section MJ-1104 Electromagnetic spring clutches Saddle section MJ-1104Solenoids Finisher section Common for MJ-1103/1104 Stapler home position sensor P11-I20 7 Fig For the stapling operationPC board Saddle section MJ-1104 Sensors and switches Saddle section MJ-1104PC board Finisher section Common for MJ-1103/1104 Diagram of Signal Blocks Finisher sectionSaddle section ROMDescription of Interface Signals Equipment connection switch Connected 24V power suppliedSent data transmitted from the Equipment to the Finisher Equipment TxD Converter RxD Finisher PC boardGeneral Description Description of Operations Basic OperationsJunction box Side alignment Unit Fold unit Stacker EFS unit Saddle trayJunction Box Junction box paper detection sensorGate flap Entrance roller Gate solenoid Simple Stack ModeFinisher paper feeding section Paper exit to the stationary tray Stationary Tray roller Entrance sensor Exit motorPaper exit to the movable tray Operation of Movable Tray Movable tray positionPosition-C sensor Job offset stack mode / Staple stack mode Paper transport sectionMulch-active drop mechanism section Paper pusher home position sensorPaper pushing arm motor Paper pushing plate Catching padDescription of Operations Stapler interference switch Bundle Job Offset OperationStapling Operation Stapler interferenceClutch Paper exiting operationStack transport roller-2 Paper exit belt Operation in the saddle stitch section Saddle stitch feeding sectionStack transport Side alignmentPaper holding StaplingFolding Folding motor encoder sensor Exit transport sensor Folding rollerAdditional folding / exiting Flow Chart Simple stack modeExit motor on Transport sensor ON?Bundle job offset mode/ stapling stack mode Center-binding mode Entrance motor onFeeding Sensor ON? Saddle transport motor onDescription Of Circuit Finishier sectionBuffer roller drive circuit Motor rotation RemarksPaper pushing arm motor drive circuit By the paper pushing plateGuide is opened Buffer tray guide motor drive circuitGuide is closed Front / rear alignment motor drive circuit Front alignment plate is closedFront alignment plate is opened Rear alignment plate is closedStack transport motor drive circuit Entrance motor drive circuit Paper is pulledOr buffer tray Exit motor drive circuitPaper is transported to the stationary tray Stapler unit is shifted to the rear side Stapler unit shift motor drive circuitStapler unit is shifted to the front side Tion Transport motor drive circuitPaper is transported to the finishing posi Paddle motor drive circuit Paper is pulled into the finishing positionThen pushed off Eliminates backlashMovable tray shift motor drive circuit Movable tray unit is shifted to the lower sideMovable tray unit is shifted to the upper side StopReset circuit Recovery operationStapler motor drive circuit IC22Saddle section Stacker motor drive circuitStacker is moved to the stapling PositionSide alignment motor drive circuit Paper is aligned to fix their sideWays deviation with a jog moved Open the jogInitial operation Only when the stapler operates abnormallyFront / Rear saddle stapler motor drive circuit Saddle transport motor drive circuit Paper is transportedAt a transport speed lower than 200 mm At a transport speed 400 mm/s or higherFolding motor drive circuit Operates the foldingPaper is exited to the saddle tray Stop Not usedAdditional folding motor drive circuit Operates the additional foldingCovers Stationary trayMovable tray Saddle trayMovable tray Leveling armConnector Control panel unitRemove 1 screw on the upper side of the front rail cover Saddle trayFront cover Front lower cover Front upper cover MJ-1104Front lower cover MJ-1104 Access cover Handle cover / Cover lock bracketRear cover Finisher cableRelay guide / Feeding discharge brush / Right cover Saddle access coverRight upper cover Left upper cover Remove 3 screws, and then take off the left upper coverClamp HookFront rail cover / Rear rail cover Take off the movable tray.  P.4-2 B Movable trayFront rail CoverConnector Grate-shaped guideRelay Shutter HookLeft lower cover Left lower cover MJ-1103 Grate-shapedGuide Clamp HarnessLeft lower cover MJ-1104 Front foot cover / Rear foot coverCover Front foot coverUnits Finisher section Junction box unitClamp If boardDisconnect the connector of the front cover switch BeltEntrance motor Buffer unitRear rail guide Paper pusher plate Buffer guide Remove 4 screws, and then take off the buffer unitBuffer unit Buffer unit-1 Disconnect the connector of the buffer tray guide motorConnector Buffer tray guide motor Relay Connector Cramp Take off the belt of the buffer roller drive motorBuffer unit-1 Finishing tray unitPlate Bushing ClipBelt SpringBelt Pin Bushing Clips Transport roller pulley-3 Stapler Flexible cableProtrusion Staple carrierMovable tray shift motor unit Measure Sensor railSensor rail Shift motor unit BracketBushing Units Saddle section MJ-1104 Saddle unitSDL board Table beneathSupport ShaftFrame Switchback unit Paper holding unit Paper holding unitRear bracket Support Bracket Front bracket Side alignment unit Saddle stapler unitPler frame assembly Install the jig on the hole of the lower sta Pler frameRemove 4 screws and take off the upper sta Upper staplerMylar Front saddle staplerFold plate Binding wire Folding drive unitRemove one clip and then remove the bush Ing Bushing ClipRemove one clip and then remove the pulley and pin Pin PulleySpring Folding drive unit Scale Mark Gear bracketWire Relay connectorEFS unit ClanpEFS jam Access leverRear bracket Stacker unit Stacker unitRollers Finisher section Feeding rollerBoard Front bracket Junction box upper Transport guideSensor Jam access leverRemove one screw, and then sensor bracket of feeding sensor Junction roller KnobPulley Pin GearRemove 3 screws, and then take off the transport guide ClipJunction roller ScrewCatching pad Arm Arm linkage portion Take off the arm by pulling it out upwardArm Rear alignment plate Front pull-in guideJig Rear pull-in guide Rear finishing tray coverPaddle shaft Rear Pull-in guide FrontFront transport roller / Rear transport roller Rear transport roller Pulley Bushing Rear transport roller Entrance rollerFront transport roller Remove 1 E-ring, and then slide 1 bushing Then take off the entrance rollerRemove 1 E-ring. Then remove 1 pulley Bushing and 1 pin from the entrance rollerStack transport roller-1 Rear finishing tray coverStack transport roller-2 Buffer roller Buffer tray guide motorRear side Remove 2 screws, and then take off the rear side frameBuffer roller drive motor Buffer roller Front buffer roller guideTake off the lift guide from the buffer roller Rear buffer roller guideSpacer Lift guideWhen installing the front and rear stationary Tions where the gap between the trailingUpper exit roller / Upper exit roller guide Tray transport guides, fix them at the posiRemove 4 screws of the upper exit roller guide Remove 5 E-rings, 1 gear, 1 pin, 1 actuator and 2 bushingsUpper exit roller guide Upper exit rollerSwitchback transport roller Feed knob Bushing Assembly BeltSwitchback Rollers Saddle section MJ-1104Assisting roller BeltEjecting roller Clip BushingRemove the 2 springs SpringBushing Pin Ejecting roller Bushing ArmBearing Upper folding roller / Lower folding rollerRemove 2 E-rings and take off the 2 bearing Remove 1 E-rings and take off the gear and pin Jam release lever Upper folding rollerPin BearingExit roller Jam release lever Lower folding rollerLower transport guide Clip Bushing Exit rollerMotor Finisher section Entrance motor M1Remove 2 screws, and then remove the motor damper Buffer tray guide motor M2Paddle motor M3 Buffer roller drive motorM4Front alignment motor Clamp Relay connector Front alignment motor M5Rear alignment motor M6 Transport motor M7Stack transport motor M8 Shaft Gear PinRemove 2 screws and then take off the bracket Stapler unit shift motor M9Relay Connector Clamp Paper pusher arm motorM10Shift motor Take off the stationary tray.  P.4-1 a Stationary trayExit motor AssemblyExit motor M11 Movable tray shift motor Sensor rail Movable tray shift motor Motor Saddle section MJ-1104 Stacker motor M14Stacker Motor bracket GearStacker Motor Clamp Upper safety coverSide alignment motor M15 Motor bracket Saddle transport motor M16Remove 2 screws, and then take off the motor bracket Remove 2 screws and take off the folding motor Folding motor M17Take off the belt of folding motor Clamp Binding wire Additional folding motor M20Paper exit guide clutch CLT2 SolenoidShutter clutch CLT1 Folding blade clutch CLT3 ProtectionTake off the junction box unit  P.4-13 a Junction box unit Paper holding clutch CLT4 MJ-1104Catching solenoid SOL1 Remove 2 screws, and then take off the catching solenoid Buffer roller lift solenoid SOL2 / Patting solenoid SOL3Solenoid sensor unit DamperGate solenoid SOL4 Buffer roller lift solenoid Patting solenoidRemove 3 screws, and then take off Remove the spring Scale Bracket Transport path switching solenoid SOL5 MJ-1104 Remove 2 screws, and then take off the gate solenoidBracket Gate flap Shaft of the entrance rollerBelt Binding wire Arm Transport path switching solenoid Surface Relay Assisting roller solenoid SOL6 MJ-1104Stacker guide Sensors / Switches Finisher section Entrance sensor S1Release the latch, and then take off the entrance sensor Transport sensor S2FIN board bracket Release the latch, and then take off the transport sensorPaddle home position sensor S3 Shutter opening / closing sensor S4 Buffer tray home position sensor S5Shutter opening Closing sensorBuffer tray home position sensor Paper pusher home position sensor S6 Front alignment plate home position sensor S7Paper pusher cam Paper pusher plateRear alignment plate home position sensor S8 Stack exit belt home position sensor S9Rear alignment Plate home position sensorTake off the belt from the stack transport motor Stack exit belt Home position sensor Stapler unit home position sensor S10Stapler interference sensor S11 / Actuator Remove the clip, and then take off the sta- pler base frame Finishing tray paper detection sensor S12Take off the finishing unit  P.4-19 D Finishing tray unit Remove 3 screws, and then take off the frontFront alignment plate guide Sensor rail Stationary tray paper-full sensor S18 Movable tray paper-full sensor S16Movable tray paper exist sensor S17 Feeding sensor S22 Spacer Actuator Stationary tray paper-full sensorRelease the latch, and then take off the feed- ing sensor Movable tray shift motor sensor S23Feeding sensor Movable tray shift motor sensorFront cover switch SW1 Remove 2 screws, and then take off the front cover switchConnection sensor S25 Connection sensorStationary tray opening/closing switch SW2 Spring Belt tension armSwitch bracket Remove 4 screws, and then take off the switch bracketStapler interference switch SW3 Connection switch SW4 Remove 4 screws, and then take off the upper saddle coverRemark Upper saddle coverRemove 2 screws, and then take off the con Nection switch Connection switchTransport path-2 sensor S27 Sensors / Switches Saddle section MJ-1104Junction box paper detection sensor S26 Transport path-3 sensor S28 Ejecting roller sensor S29 Stacker paper detection sensor S30 Stacker paper detection sensorExit sensor S31 Release the latch, and then take off the exit sensorSaddle tray paper detection sensor S32 Exit sensorStacker home position sensor S33 Folding motor encoder sensor S34Stacker guide Folding motorFolding blade home position sensor S35 Side alignment home position sensor S36Paper holding home position sensor S38 Additional folding home position sensor S39Folding carrier to the center Sensor bracketExit transport sensor S41 Additional folding motor encoder sensor S42Exit transport sensor Additional folding motor encoder sensorSaddle unit opening/closing switch SW5 Connector and take off the sensor bracketSaddle unit opening/closing switch Remove 2 screws, and then disconnectRemove 4 screws, and then take off the FIN board PC Boards / Discharge BrushFinisher control PC board FIN board Interface PC board I/F board Remove 4 screws, and then take off the I/F boardSaddle control PC board SDL board Front stationary tray Discharge brushMylar Rear stationary trayProcedure for lowering the movable tray Since the insertion of the screwdriver hasReleased the driving gear of the movable tray Stationary trayAdjusting the Alignment Position Adjusting for A4 size paper Adjusting for LT size paperButton1 Button2 B5 paper Vertical Adjustment sheetRemarks Number of Blinking Adjustment Value Adjusting the Stapling Position LED3 LED2 Stapling/folding position adjustment in saddle unit SamplePhenomenon Contents Adjustment Folding position adjustment Number of blinking Adjustment value Stapling position adjustment Number of blinking Adjustment value Saddle Stitch Skew Adjustment Paper jam in entrance section EA10 Transport delay jam paper not insertedPaper Transport Jam EA60 Early arrival jam CB10 Entrance motor M1 abnormalityPaper jam in buffer unit-1 EA20 Paper transport jam in Finisher entrance sensorTroubleshooting EA31 Transport path paper remaining jam in Finisher EA28 Paper transport jam in Finisher paper holding delayPaper jam in buffer unit-2 ED16 Buffer tray home position error CB14 Paper pusher arm motor M10 abnormality Paper jam in finishing tray sectionCB12 Buffer roller drive motor M4 abnormality ED13 Front alignment plate home position error ED14 Rear alignment plate home position errorED15 Paddle home position error EA70 Stack exit belt home position error CC41 Paper pusher cam home position abnormality EA32 Exit paper remaining jamCB31 Movable tray paper-full detection error ED12 Shutter home position errorPaper jam in movable tray section CB30 Movable tray shift motor M12 abnormalityCover open jam EA40 Cover open errorEA90 Saddle unit open error MJ-1104 Troubleshooting Paper Transport Jam in Saddle Stitch Section MJ-1104 Paper jam in Saddle Stitch Finisher transport sectionEAA0 Paper remaining in Saddle Stitch FinisherEAB0 Paper transport jam in Saddle Stitch FinisherShort paper jam in Saddle Stitch Finisher EAB1EF14 Saddle exit jam EF13 Saddle unit paper holding home position detection error EF20 Saddle stacker jam Paper jam in side alignment sectionPaper jam in stack transport section Troubleshooting Paper jam in folding section EF19 Saddle Stitch Finisher paper folding jamPaper jam in additional folding section Other Errors Stapler related errorEA50 Stapling jamCB51 Stapler shift home position error CB60 Stapler unit shift motor M9 abnormalitySaddle Stitch Finisher stapler related error MJ-1104 EF11 Front saddle staple errorEF12 Rear saddle staple error CBA0 Front saddle stapler home position errorWhen MJ-6102 is connected Communication Related ErrorCBB0 Rear saddle stapler home position error Memory error CB81 Flash ROM abnormality CB91 Saddle flash ROM abnormalityMaintenance and Inspection Points Front side Rear sideSymbols used in the checklist Preventive Maintenance ChecklistCleaning Lubrication/Coating Replacement Operation check Items to check Cleaning Lubrication Replacement OperationBuffer tray shaft Finishing tray shaft Rack gear EFS carrier shaft Firmware Update Update of CNV boardConnector Mark for ROM Installation directionDownload jig Update of FIN board Preventive Maintenance PM / Firmware Update Update of SDL board Download jigPreventive Maintenance PM / Firmware Update Preventive Maintenance PM / Firmware Update Harness Diagram Finisher control PC boardElectric Circuit Interface PC board Opening/closing switch Saddle control PC boardCircuit Diagram Finisher control PC board 1. Circuit DiagramCircuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Interface PC board 1. Circuit Diagram Circuit Diagram Saddle control PC board 1. Circuit Diagram 2008, 2009 Toshiba TEC Corporation All rights reserved Circuit Diagram 2008, 2009 Toshiba TEC Corporation All rights reserved Circuit Diagram 2008, 2009 Toshiba TEC Corporation All rights reserved Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Circuit Diagram Electric Circuit PC board Finisher controller PC board Interface PC boardSaddle control PC board Electric Circuit Ver.01 Ver.03Ver.02 Revision Record