Configuration | Western Telematic RSM-8, RSM-32DC, RSM-16DC instruction

Configuration

To access command mode via the Text Interface, proceed as follows:

Note: Command mode cannot be accessed via a Buffer Mode Port, Passive Mode Port, or any port that is presently connected to another RSM port.

1.Contact the RSM Unit:

a)Via Local PC: Start your communications program and press [Enter]. Wait for the connect message, then proceed to Step 2.

b)Via Network: The RSM includes a default IP address (192.168.168.168) and a default subnet mask (255.255.255.0.) This allows you to contact the unit from any network node on the same subnet, without first assigning an IP Address to the unit. For more information, please refer to Section 5.8.

i.Via SSH Client: Start your SSH client, and enter the RSM’s IP Address. Invoke the connect command, wait for the connect message, then proceed to Step 2.

ii.Via Telnet: Start your Telnet Client, and then Telnet to the RSM’s IP Address. Wait for the connect message, then proceed to Step 2.

Note: When communicating with the unit for the first time, you will not be able to contact the unit via Telnet, until you have accessed command mode, via Local PC or SSH Client, and used the Network Parameters Menu (/N) to enable Telnet as described in Section 5.8.

c)Via Modem: Use your communications program to dial the number for the line connected to the RSM’s Phone Line port.

2.Login / Password Prompt: A message will be displayed, which prompts you to enter a username (login name) and password. The default username is "super" (all lower case, no quotes), and the default password is also "super".

PORT	STATUS:				02/07/2007 00:23:39 GMT (GMT+0000)
Site	ID: (undeﬁned)				02/07/2007 00:23:39 GMT (GMT+0000)
PORT		NAME		USERNAME	STATUS			MODE	BUFFER COUNT
-----+------------------			+------------------		+--------	Free	+--------	Any	+--------------	0
01	(undeﬁned)					Free		Any		0
02	(undeﬁned)					Free		Any		0
03	(undeﬁned)					Free		Pass		0
04	(undeﬁned)					Free		Pass		0
05	(undeﬁned)					Free		Pass		0
06	(undeﬁned)					Free		Pass		0
07	(undeﬁned)					Free		Pass		0
08	(undeﬁned)					Free		Pass		0
09	MODEM					Free		Modem		0

Enter /H for command menu.

RSM>

Figure 5.1: The Port Status Screen (Text Interface; RSM-8 Shown)

5-2

Image 21

Western Telematic RSM-8, RSM-32DC, RSM-16DC manual Configuration

Contents

RSM Series Secure Racking Shock Hazard Do Not Enter Lithium Battery Disconnect Power Agency Approvals Table of Contents Configuration Table of Contents List of Figures Introduction Security and Collocation FeaturesIntelligent Port Selection Capture Buffer RSM-8, RSM-16, RSM-16DC, RSM-32 and RSM-32DC Units Configuration BackupTypographic Conventions Bold Font Front Panel Unit Description Instrument Back Panel Model RSM-8 Back Panel  Power On/Off Switch Apply Power to the RSM Quick Hardware InstallationGetting Started Connect your Control Device to the RSM Communicating with the RSM Port Status Screen Text Interface RSM-8 Shown Getting Started Hardware Installation Connecting Power to the RSM UnitDC Powered Units Connecting Devices to the RSM Connecting the Network Cable Configuration Communicating with the RSM UnitText Interface Configuration Home Screen Web Browser Interface Web Browser Interface Configuration Menus System SetUp Ports System Parameters Defining System Parameters Configuration Real Time Clock and Calendar Invalid Access Lockout Feature Audit Log Callback Security Configuration Supervisor Access Port AccessUser Accounts Viewing User Accounts Managing User Accounts Add User Menu Text Interface RSM-8 Shown Adding User Accounts Configuration Deleting User Accounts Modifying User Accounts 1. RS232 Port Modes RS232 Port Configuration Port Configuration Menu Text Interface Communication Settings 2. RS232 Port Configuration Menus General Parameters AT&C1&D2S0=1&B1&H1&R2 Port Mode Parameters Network Services Configuring the Internal Modem Servers and Clients Network Configuration Configuration 11 Network Parameters Menu Web Browser Interface Network Parameters 12 Network Port Parameters Menu Web Browser Interface Network Port Parameters Configuration IP Security IP Security Configuration Configuration Net/Mask Pairs Except Configuration 15 Static Route Menu Text Interface Static Route 17 Nomain Name Server Menu Text Interface Domain Name Server Snmp Parameters 19 Snmp Access Menu Text Interface Configuration Ldap Ldap Parameters Configuration Ldap Group Group Membership Value Type Default = DN 25 Add Ldap Group Menu Text Interface RSM-8 Shown 27 View Ldap Group Menu Text Interface RSM-8 Shown 29 Modify Ldap Group Menu Text Interface RSM-8 Shown 31 Delete Ldap Group Menu Web Browser Interface 32 Ldap Kerberos Set Up Menu Text Interface Configuration 34 The Tacacs Parameters Menu Text Interface Tacacs Parameters Configuration 36 The Radius Parameters Menu Text Interface Radius Parameters Configuration 38 The Copy Port Parameters Menu CP 3,5,7-9 Enter Save User Selected Parameters Status Screens Status Screens Port Status Screen /S Port Diagnostics Screen RSM-8 Shown Port Diagnostics Screen /SD Porttcp Portstatus Username Network Status Screen /SN Port Parameters Screen RS232 Port Shown Port Parameters Screens /W Xx Enter Any-to-Any Mode OperationPort Connection and Disconnection Operation Operation Enter 4 Enter Hunt Group Example Defining Hunt Groups Passive Mode Reading Data from Buffer Mode Ports Buffer Mode Port Buffers Modem Mode Telnet & SSH Functions Network Port NumbersSSH Encryption Direct Connect Feature ConfigurationStandard Telnet Protocol, SSH and Raw Socket Telnet & SSH Functions SSH Direct Connection with Password RSM-8 Standard Telnet Direct Connection without Password RSM-8RSM-16 & RSM-16DC RSM-32 & RSM-32DC Raw Socket Direct Connection with Password RSM-8 Raw Socket Direct Connection without Password RSM-8Connection Example Terminating a Direct Connect Session Configuration Syslog Feature Criteria for Generating a Syslog Message Test Menu Text Interface, Supervisor Mode Only Testing Syslog Configuration 10-1 Snmp Traps How and When Snmp Traps are Sent Snmp Trap MessageSnmp Contact Optional Snmp Location Optional Testing the Snmp Trap Function Sending Parameters to a File Saving and Restoring Configuration Parameters Restoring Saved Parameters 12-1 Upgrading RSM Firmware 12-2 Command Conventions Command Reference Guide Command Summary Command Set Resident Disconnect SequenceAudit Log Format /C x x Enter ConnectCP Copy RS232 Port Parameters Format /CP Enter Format /D/Y x x Enter Third Party Disconnect2 Enter or /D/Y 3 Enter Erase Buffer Set System Parameters Reboot System DefaultHelp Display Site ID Send SSH Key Set Network Port ParametersSet RS232 Port Parameters SD Display Port Diagnostics PW Change PasswordRead Buffer Display Port Status UL Unlock Port Invalid Access Lockout UF Upgrade FirmwareTest Test Network Parameters Save Parameters Display Port Parameters Who Exit Command ModeFormat /W x Enter Format /X Enter When connected When not connectedAppendix A. RS232 Port Interface RS232 Port Interface Connectors Appendix B. SpecificationsPhysical / Environmental Power Models RSM-32 and RSM-32DC Appendix C. Customer Service Trademarks Used in this Manual Trademark and Copyright Information Tacacs Dhcp Index Index-2 Index-3 Index-4