Manuals / 3Com / Computer Equipment / Server

3Com CS/2500 manual

Models: CS/2500

1 116

Download 116 pages 10.75 Kb

Troubleshooting Specs Install Warranty Maintenance Configuration Boot Problems Remove Connector from Procedure Services

Page 10

Image 10

x

Image 10

3Com CS/2500 manual

Our partner
Обсуждение вопроса Почему аллерготест может быть неверным? из чата 🇺🇦 Чат Мюнхена/Германии не для мальчиков, Мюнхен, Германия
Прокачай грамматику английского Переводи тысячи предложений на разные правила грамматики

Related pages Troubleshooting Points for Poulan 181121 Specifications for Audiovox AV-970 Time countdown indicator lights up for JVC KD-SH909 Camera Timing Charts for JAI TMC-4200GE When burner is lit HI position when burner is for Desa T32N-a SERIES Installing the Monitor Driver Automatic for Samsung LS22CMFKFV/ZN MKB-2081 Parts List for Impex MKB-2081 Language Code List for Magnavox MDV560VR Date/Time Settings for SRS Labs 8953H Wi-Fi intermitente for Samsung UE43LS003AUXZG Is the 3.5mm audio cable included with the ACU5501A-R4? Find out more

Contents

CS/2500 Series 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Installation Maintenance and Upgrades PIN Assignments Technical Support Page Figures Tables Audience About this GuideIntroduction Conventions This Typeface Italics Italics are used to denote new terms or emphasis About this Guide Overview FeaturesFeatures Ten standard RS-232-D electrical interfaces Compatibility SoftwareSW/2500, can be used only with the CS/2500 and CS/2600 Chassis Panel, see Back Panel on Hardware Interrupt Front Panel Its +5 V DC output Back Panel Power supply module and three types of connectorsCS/2500 and CS/2600 back panel, shown in -5, contains Overview Back Panel Overview Optional Rack SpecificationsMount Kit VAC Do the following before beginning the installation InstallationPreparation Installation Install brackets To the Network Cabling the ServerTurning on the server All ports are set to terminal SETDefault -TERM DeVice = Installation Slide-lock connection on the server End to the transceiver Install brackets Configuration, and Appendix C, Monitor Utility ConfigurationAC power source must meet the requirements outlined Modifying Installation Startup Guide or software release notes Rbcs files Booting fromDiskette Diskette Startup 3Com Corporation CS/2000 Series Monitor Reading...OK Insert copy and hit return to continue Parameter changes Messages Boot ProblemsNormal Startup Shutting Down Shutting Down Startup Entering ConfigurationFirmware Monitor Configuration Changing ProcedureFollowing menu is displayed SLP Changing the Configuration Configuration Changing the Configuration Used with 3Com Network Control Servers NCSs Com no longer SLP, and Trivial File Transfer Protocol TftpNext section Type B Change IP/TFTP Parameters menu appears Tftp Configuration Bootp CS/2000 or CS/2100 Emulating aSoftware and to operate in mixed environments Changing Port Configuration Changing Port Configuration Configuration 3Com recommends the following procedures for preventive Maintenance and UpgradesMaintenance Maintenance Maintenance and Upgrades Maintenance Reinstall the fuseholder cartridge in the receptacle Upgrades Upgrade procedures require you to remove the server cover Removing the Server Cover Grasp both sides of the cover and carefully lift it off Rear 8-F Pull taut to expose screw Voltages. There are no user-serviceable parts inside Upgrades Remove Connector from Each pin must be inserted properly into its socket EPROM. Each pin must be inserted properly into its socket Replace the cover, as described in the next section Upgrades Maintenance and Upgrades Troubleshooting Troubleshooting Operating Problems Troubleshooting Procedures Memory Dump Enter the density of the dump diskettes Return to use the default density 2mb Troubleshooting Figure A-1 Serial Connector Pin Numbering PIN Assignments TXD DTE Transceiver DO-S Slct Startup Messages Appendix B Startup Messages You can access the monitor in either of the following ways Monitor Utility Continuous Self-Test and Initial Boot Source parameters Set the Auto-reboot parameter to Boot monitorNonfunctional Become nonfunctional, enter the following command Memory dumps, refer to Memory Dump Procedures on-2 on page 1-4. The switch is recessed into a round hole to Dump Procedures on Syntax BT Filename and address parameters specify the name Procedures onUsing this menu, refer to , Configuration From memory location Description Repeats the previous command Technical Support Services3Com Bulletin Board Service 3ComBBS On-line Technical Press Return to see the ThreeComForum main menu Country Telephone Number Hong Kong 852 2537 44 1442 408 727 Appendix D Technical Support For Repair Returning ProductsSender’s expense To obtain an RMA number, call or fax 10/25/95 Index Numerics Cover Index Index Index Index Limited Warranty Bayfront Plaza Santa Clara, CA 408 764-5000 1/1/94

Top Page Image Contents