Manuals / 3Com / Computer Equipment / Server

3Com CS/2500 manual Installation

Models: CS/2500

1 116

Download 116 pages 10.75 Kb

Troubleshooting Specifications Install Warranty Maintenance Configuration Boot Problems Remove Connector from Procedure Services

Page 38

2-10 CHAPTER 2: INSTALLATION

Page 37 Page 39

Image 38

3Com CS/2500 manual Installation

Page 37 Page 39

Related pages All Install page Installing the Switch for HP General IO Connectivity Installation for Samsung LS27C750PS/EN Outdoor Lighting Fixture Installation Instructions for Westinghouse w-143 Installation universelle à laide du manchon du montage for Audiovox MP5620SE Installation for Hubbell MMD24 Installing the DVD Player Unit for Pioneer XDV-P90 When installing your fridge freezer for Hotpoint FFA84 Installation and Removal for Q-Logic 2300 series Installation for Southbend STRE-3D Procedura dinstallazione for Samsung NB19BSPS/EDC What should I do if I lose screws while disassembling the Casio CTK-230? Click for tips

Contents

CS/2500 Series 3Com Corporation 5400 Bayfront Plaza Santa Clara, California Iii Page Contents Installation Maintenance and Upgrades PIN Assignments Technical Support Page Figures Tables Audience About this GuideIntroduction Conventions This Typeface Italics Italics are used to denote new terms or emphasis About this Guide Overview FeaturesFeatures Ten standard RS-232-D electrical interfaces SW/2500, can be used only with the CS/2500 and CS/2600 SoftwareCompatibility Chassis Panel, see Back Panel on Hardware Interrupt Front Panel Its +5 V DC output CS/2500 and CS/2600 back panel, shown in -5, contains Power supply module and three types of connectorsBack Panel Overview Back Panel Overview Mount Kit SpecificationsOptional Rack VAC Preparation InstallationDo the following before beginning the installation Installation Install brackets Turning on the server Cabling the ServerTo the Network All ports are set to terminal SETDefault -TERM DeVice = Installation Slide-lock connection on the server End to the transceiver Install brackets Configuration, and Appendix C, Monitor Utility ConfigurationAC power source must meet the requirements outlined Modifying Installation Startup Guide or software release notes Rbcs files Booting fromDiskette Diskette Startup 3Com Corporation CS/2000 Series Monitor Reading...OK Insert copy and hit return to continue Parameter changes Messages Boot ProblemsNormal Startup Shutting Down Shutting Down Startup Firmware Monitor ConfigurationEntering Configuration Following menu is displayed ProcedureChanging SLP Changing the Configuration Configuration Changing the Configuration Next section SLP, and Trivial File Transfer Protocol TftpUsed with 3Com Network Control Servers NCSs Com no longer Type B Change IP/TFTP Parameters menu appears Tftp Configuration Bootp Software and to operate in mixed environments Emulating aCS/2000 or CS/2100 Changing Port Configuration Changing Port Configuration Configuration 3Com recommends the following procedures for preventive Maintenance and UpgradesMaintenance Maintenance Maintenance and Upgrades Maintenance Reinstall the fuseholder cartridge in the receptacle Upgrades Upgrade procedures require you to remove the server cover Removing the Server Cover Grasp both sides of the cover and carefully lift it off Rear 8-F Pull taut to expose screw Voltages. There are no user-serviceable parts inside Upgrades Remove Connector from Each pin must be inserted properly into its socket EPROM. Each pin must be inserted properly into its socket Replace the cover, as described in the next section Upgrades Maintenance and Upgrades Troubleshooting Troubleshooting Operating Problems Troubleshooting Procedures Memory Dump Enter the density of the dump diskettes Return to use the default density 2mb Troubleshooting Figure A-1 Serial Connector Pin Numbering PIN Assignments TXD DTE Transceiver DO-S Slct Startup Messages Appendix B Startup Messages You can access the monitor in either of the following ways Monitor Utility Nonfunctional Set the Auto-reboot parameter to Boot monitorContinuous Self-Test and Initial Boot Source parameters Become nonfunctional, enter the following command Memory dumps, refer to Memory Dump Procedures on-2 on page 1-4. The switch is recessed into a round hole to Dump Procedures on Syntax BT Filename and address parameters specify the name Procedures onUsing this menu, refer to , Configuration From memory location Description Repeats the previous command Technical Support Services3Com Bulletin Board Service 3ComBBS On-line Technical Press Return to see the ThreeComForum main menu Country Telephone Number Hong Kong 852 2537 44 1442 408 727 Appendix D Technical Support Sender’s expense To obtain an RMA number, call or fax Returning ProductsFor Repair 10/25/95 Index Numerics Cover Index Index Index Index Limited Warranty Bayfront Plaza Santa Clara, CA 408 764-5000 1/1/94

Top Page Image Contents