Manuals / Agilent Technologies / Computer Equipment / Computer Accessories

Agilent Technologies 16700B manual Installing Pattern Generator Measurement Modules

Models: 16700B

1 150

Download 150 pages 57.59 Kb

Troubleshooting Install Connecting Accessories Warranty Impedance ConnecTOR connector Safety

Page 87

5

Installing Pattern Generator Measurement Modules

87

Page 86 Page 88

Image 87

Agilent Technologies 16700B manual Installing Pattern Generator Measurement Modules

Page 86 Page 88

Related pages All Install page Installing glass doors for Desa ICBO# 3507 USE only the Installation Method Specified below for Pentair SunLite LTC Installation on a Perpendicular Wall for Samsung LH40DHDPLGC/XY Quick Installation and Configuration for Citrix Systems 8015 Setting will be taken from the initial installation for Philips DVDR3570H58 Installation for Lincoln Electric SVM 106-A Instructions d’installation et for Whirlpool GZ7930XGS0 Install the Pilot Burners for PB Heat 211A Installation for Samsung LH55UDEBLBB/CH Installing the Switch for 3Com 4210G How can I provide feedback on my experience with the 三星应用商店?

Contents

Agilent Technologies 16700B-Series Logic Analysis Systems Installation at a Glance 16702B Overview Page General Information Contents Installing Oscilloscope Installing Pattern Generator Troubleshooting General Information To locate information on using the logic analyzer To locate specifications and characteristics To locate specifications and characteristics General Information General Information To reload system settings and license passwords Select Flexible Disk or Mounted Directory and select OK Connecting and Configuring Hardware To connect the mouse, keyboard, and monitor To configure a monitor for the 16700B Clear Images To configure an optional monitor for the 16702B To connect to LAN To change monitors 16700B or 16702B To connect to LAN To connect a printer Your Printer To connect an external data drive option To connect an external data drive option Connect the data drive to the SCSI-II port To connect an external data drive option To disconnect an external data drive option To connect a removable boot drive option To connect a removable boot drive option 68 pin To install software To disconnect a removable boot drive option To install software To load System Software, highlight it and select Install To connect a 16701B expander frame Option #012 and/or 16702B option #012 To connect multiple frames To connect multiple frames Insert the Multiframe Module with the cable attached 16700e25.cdr To install, remove, or replace measurement modules To install, remove, or replace measurement modules To install, remove, or replace measurement modules Installing Logic Analyzer Measurement Modules Model Number Software Version Software Requirements 16517/18A Logic Analyzer 2-card module 16517/18A Logic Analyzer 3-card module Modules following the procedures on 16517/18A Logic Analyzer 4-card module 16557D Logic Analyzer 1-card module 16517/18A Logic Analyzer 5-card module 16557D Logic Analyzer 2-card module 16557D Logic Analyzer 3-card module 16557D Logic Analyzer 3-card module 16557D Logic Analyzer 5-card module 16710/11/12A Logic Analyzer 1-card module 16710/11/12A Logic Analyzer 2-card module Logic Analyzer 1-card module Installing Logic Analyzer Measurement Modules Logic Analyzer 3-card module Installing Logic Analyzer Measurement Modules Logic Analyzer 5-card module 16753/54/55/56A Logic Analyzer 1-card module 16753/54/55/56A Logic Analyzer 2- card module 16753/54/55/56A Logic Analyzer 3-cardmodule 16753/54/55/56A Logic Analyzer 4- card module 16753/54/55/56A Logic Analyzer 5-cardmodule 16760A Logic Analyzer 2-card module 16760A Logic Analyzer 1-card module 16760A Logic Analyzer 3-card module 16760A Logic Analyzer 4-card module 16760A Logic Analyzer 5-card module Installing Oscilloscope Measurement Modules Prepare a single 16533/34A card for calibration Modules Would be effective for the current active session only 16700B or 16702B Step Perform operational accuracy calibration RUN 16533/34A Oscilloscope Module single or multi-card modules Step Calibrate a single card for external trigger skew RUN 16533/34A Oscilloscope Module single or multi-card modules Step Reconfigure multi-card modules Reapply power to the 16700-series mainframe RUN RUN Unprotected Protected Page Installing Pattern Generator Measurement Modules 16522A Pattern Generator 1-card module 16522A Pattern Generator 3-card module 16522A Pattern Generator 2-card module 16522A Pattern Generator 4-card module 16522A Pattern Generator 5-card module 16720A Pattern Generator 2-card module 16720A Pattern Generator 1-card module 16720A Pattern Generator 3-card module 16720A Pattern Generator 4-card module 16720A Pattern Generator 5-card module Page Connecting Accessories For More Information General-purpose probing 100 101 Pod Direct connection Cable end that connects to the high-density AMP Mictor Impedance ConnecTOR connector Target system 106 107 108 Works with Half-channel Adapter E5386A Single-ended Flying Lead Probe Set E5382A 111 Time Correlation Fixture E5850A Troubleshooting To run self-tests Type SEA Enter To execute disaster recovery procedures At the prompt Numerics Index 118 119 120 S1 Declaration of Conformity ICES/NMB-001 Pattern Generator Module Sound Pressure Level Regulatory Information for Canada 16533A and 16534A ICES/NMB-001 Logic Analyzer Module IEC 555-2 and IEC Group 1 Class A1 Sound Pressure Level Safety IEC 1010-11990+A1 / EN CSA-C22.2 No Equipment IEC 555-2 and IEC S1 Declaration of Conformity ICES/NMB-001 S1 Declaration of Conformity Required IEC 61326-11997+A11998 / EN 61326-11997+A11998 ICES/NMB-0011998 Group 1 Class A1 IEC 61010-11990+A11992+A21995 / EN 61010-11994+A21995 IEC 61000-4-31995/EN 3V/m, 80% AM IEC 61000-4-41995/EN ICES/NMB-001 S1 Declaration of Conformity ICES/NMB-001 IEC 61326-22002/ EN Group 1 Class A1 Ccispr 111997+A11999/EN IEC 61326-22002 / EN Ccispr 111990/EN ICES/NMB-001 Safety Document Warranty

Top Page Image Contents