Manuals / Bay Technical Associates / Computer Equipment / Network Router

Bay Technical Associates none manual Continuing with Directed Netboot

Models: none

1 156

Download 156 pages 62.12 Kb

Page 71

Starting the ARN

Continuing with Directed Netboot

Note: Continuing with the directed netboot option requires that you have already logged in to the Technician Interface or ARN monitor command line software. Refer to the previous section, “Logging in to the Command Line Software,” for instructions.

You must have at least one serial, DSU/CSU, Ethernet, or token ring interface connected to the network to use the directed netboot option. Before you start the directed netboot procedure, ask your network administrator to

•Verify that the network is set up so that you can start the directed netboot procedure.

•Provide you with the ifconﬁg command to use in Step 1.

•Provide you with the boot option conﬁguration commands (bconﬁg) to use in Step 2.

Note: Refer to Appendix A for more information about the ifconﬁg and bconﬁg commands.

The ifconﬁg command conﬁgures the parameters necessary to load the software image and conﬁguration ﬁles from a remote server over the network. Write the command in Table 2-3 for your reference.

Table 2-3. Your ifconﬁg Command -- Directed Netboot

ifconﬁg

114200 Rev. A

2-11

Image 71

Bay Technical Associates none manual Continuing with Directed Netboot, Your ifconﬁg Command -- Directed Netboot Ifconﬁg

Contents

Installing and Operating BayStack ARN Routers Third-Party Trademarks Copyright 1988-1996 Bay Networks, IncRestricted Rights Legend Trademarks of Bay Networks, IncEN 55 022 Declaration of Conformance USA Requirements OnlyEuropean Requirements Only Voluntary Control Council for Interference Vcci Statement Japan/Nippon Requirements OnlyCanada CS-03 -- Règles et règlements Canada Requirements OnlyCanada CS-03 Rules and Regulations C. Explanatory Notes Equipment Attachment Limitations Vii Bay Networks Software License Bay Networks Software License Page Contents Chapter Starting the ARN Chapter Operating the ARN Appendix B Using Local Boot the Quick-Start Procedure Index Page Figures Figure D-1 Cable Tables Table C-3 You enter ping About This GuideBefore You Begin ConventionsAcronyms About This Guide Ordering Bay Networks Publications Technical Support and Online Services Region Telephone Number Fax Number Bay Networks Customer ServiceWorld Wide Web Bay Networks Information ServicesCustomer Service FTP CompuServe Support Source CDTechnical Response Center Telephone Number Fax Number How to Get HelpInfoFACTS Page Installing the BayStack Advanced Remote Node Verifying Shipment Contents Preparing to Install the ARNIllustrates the ARN shipping accessories Mounting Hardware Service ConsoleSupplying Equipment CablesPositioning the ARN on a Flat Surface Installing the ARNInstallation Space Requirements Verifying Site RequirementsRack-Mounting the ARN Attaching Flange Brackets to Rack-Mount the ARN Installing the ARN in an Electronic Enclosure Rack ARN Module Locations Understanding the ARN Module LocationsConnecting to an Ethernet Interface Connecting Communications CablesConnecting an AUI Cable Connecting to an AUI InterfaceConnecting a 10Base-T Ethernet Cable Connecting to a 10Base-T InterfaceConnecting to an STP Token Ring Interface Connecting to a Token Ring InterfaceConnecting Token Ring UTP Cables Connecting to a UTP Token Ring InterfaceConnecting Serial Cables to an Expansion Module Connecting to a Serial Interface10. Connecting a Serial Cable to a Serial Adapter Module 11. Connecting an Isdn BRI Cable Connecting to an Isdn Interface12. Connecting a DSU/CSU Cable Connecting to a DSU/CSU InterfaceModem Signal/Parameter Value Connecting to a V.34 Modem InterfaceModem Adapter Module Defaults To connect to a V.34 modem interface Parameter Value Connecting a Terminal ConsoleConsole Parameters Attaching the Null Modem Adapter15. Connecting a Terminal Console to an ARN Connecting a PC Console16. Connecting a PC Console to an ARN External Modem Parameters Connecting a ModemConnecting to the Back-Panel Modem Port Refer to the modem user guide for instructions Back-Panel V.34 Modem Defaults Connecting to a V.34 Modem Module18. Connecting the Power Cable Connecting the Power Cable19. Flash Memory Card Installing the Flash Memory CardFor information about Go to Where to Go NextPage Chapter Starting the ARN Software InstallationSummary of Initial Startup Options Understanding the ARN Boot OptionsSummary of Initial Startup Options Starting the ARN for the First Time Using EZ-Install Interrupting the Boot Process Using Netboot, Directed Netboot, or Local BootManager Logging in to the Command Line SoftwareYour ifconﬁg Command -- Netboot Ifconﬁg Continuing with NetbootVerifying the Interface Conﬁguration Following is a sample command ifconﬁg com1 9.0.0.2 255.0.0.0Ensure that the ARN boots correctly Your ifconﬁg Command -- Directed Netboot Ifconﬁg Continuing with Directed NetbootYour bconﬁg Commands Bconﬁg image Bconﬁg conﬁg Verifying Directed Netboot Conﬁguration Ensure that the ARN boots correctly Bconﬁg conﬁg local Continuing with Local Boot the Quick-Start ProcedureRun instarn.bat Choose whether you want to conﬁgure another module/portWhere to Go Next Page Chapter Operating the ARN Base Module LEDs Diagnostic LEDsLED Descriptions Meaning Base Module Diagnostic LEDsBase Module Token Ring LEDs Ethernet LEDsToken Ring LEDs Base Module Ethernet LEDsExpansion Module Token Ring LEDs Expansion Module LEDsExpansion Module Ethernet LEDs Expansion Module Serial LEDs Adapter Module LEDsSerial LEDs Serial LEDDSU/CSU LEDs Isdn BRI LEDs S/T or U InterfacesDSU/CSU LEDs Isdn BRI LEDsModem LEDs Back-Panel LEDsModem LEDs Boot Status Run LED Boot LED Ensuring a Successful InstallationBoot Status LEDs ARN Power Switch Powering On and Off the ARNARN Reset Button Resetting the ARNRemoving an ARN Flash Memory Card Removing a Flash Memory CardProtecting Memory Card Files Memory Card Read/Write Protect SwitchWhere to Go Next Using the ifconﬁg Command Appendix a Conﬁguring the ARN for Netboot Directed NetbootFr -annexd -lmi -annexa-intclk Conﬁguring an IP Serial or DSU/CSU Interface for NetbootingTable A-1. ifconﬁg Command Settings for a COM Interface Setting Description Default SettingTable A-1 Ifconﬁg Command Settings for a COM Interface IP Address Settings Conﬁguring an Ethernet Interface for Network BootingIP Connector Setting Rspeed Conﬁguring a Token Ring Interface for Network BootingEnabling and Disabling Interfaces with ifconﬁg Ifconﬁg Command ExamplesBconﬁg -d image conﬁg Using the bconﬁg CommandBconﬁg Command Format Table A-5 Bconﬁg Command SettingsBconﬁg image network bconﬁg conﬁg network Bconﬁg Command ExamplesVerifying Your Conﬁguration Boot Options Page Appendix B Using Local Boot the Quick-Start Procedure Module Interface Base Expansion Adapter Understanding Quick-Start Connector Names and NumbersTable B-1 Quick-Start Connector Names and Numbers Fill out one Wide Area Protocol worksheet Filling Out the WorksheetsStep Requested Information Options Your Response Global Information WorksheetGlobal Information Worksheet Global Information Worksheet RIP Requested Information Options Your Response Router Protocol WorksheetsRIP Worksheet Ospf Worksheet Ospf Worksheet Static Route to Site Manager Worksheet Bay Networks Proprietary PPP Worksheet Wide Area Protocol WorksheetsAddr Q.922 November Frame Relay WorksheetChap PPP Standard WorksheetPPP Standard Worksheet Smds Worksheet Running the Quick-Start ScriptPress Control-c Table B-2 Quick-Start CommandsTask Action Details Name and save the conﬁguration ﬁle Page Physical Speciﬁcations Appendix C Technical SpeciﬁcationsCountry Outlet Voltage Electrical SpeciﬁcationsEnvironmental Speciﬁcations Table C-1 ARN Wall Outlet RequirementsHardware Communications Options Network Interface Description Table C-2 Network Interfaces Available on ARNsTable C-3 AUI Pin Assignments Pin Assignment Pin No Signal NameEthernet Attachment Unit Interface AUI Table C-4 Base-T Interface Pin Assignments Pin Assignment Pin No Signal FunctionEthernet 10Base-T Interface Table C-5. Token Ring STP Interface Pin Assignments Token Ring STP InterfaceTable C-6. Token Ring UTP Interface Pin Assignments Token Ring UTP InterfaceSerial Interfaces Table C-7 Serial Interface Pin Assignments Pin Assignment Pin No. Signal NameTable C-8. Isdn BRI U Interface Pin Assignments Pin Assignment Pin No SignalIsdn BRI U Interface Table C-9. Isdn BRI S/T Interface Pin Assignments Isdn BRI S/T InterfaceTable C-10. DSU/CSU Interface Pin Assignments 56/64K DSU/CSU InterfaceTable C-11. V.34 Interface Pin Assignments RJ-11 Interface for V.34 ModemLocal Console Connections Table C-12. Local Console Port DB-9 Pin Assignments Service Modem ConnectionsPin Assignment Pin No Signal Name Direction Table C-13. Service Modem Port DB-9 Pin Assignments Page Port Location Port Description Type of Circuit ARN Ethernet Base Model Safety StatusAppendix D Requirements for European Operation ARN Expansion Modules Safety Status ARN Token Ring Base Model Safety StatusSynchronous Cabling Requirements Bay Networks Termination Remote Termination Pin SignalTable D-4 WAN Interface Order No Table D-5 Interface Order No Local Wire ConnectionsTable D-6 Interface Order No Figure D-3. Cable 7224 X.21 CompliantSerial Adapter Module Requirements Table D-7 Safety Status Order No. CV0004001Isdn BRI Adapter Module Requirements Table D-8 Isdn BRI Safety Status Order No. CV0004002Table D-9 Isdn Connector Pinouts Pin SignalAmperage Power Requirements for Isdn BRI and Serial Adapter ModulesTable D-10. Isdn BRI Power Requirements Clearance Creepage Y Host or expansion card Voltage used or generated by other partsRequirements for European Operation Page Index SymbolsIndex-2 Index-3 Index-4 Index-5 Index-6 Index-7 Index-8