Extron electronic 450 manual $Ls

Command and Response Table for SIS Commands (continued)

Command Function	SIS Command	Response	Additional description
	(Host to Unit)	(Unit to Host)

View ties, gain, volume, mutes, and presets (continued)

View video room preset	EX1)*X(*X@*1VC}	X!n•X!n+1•...•X!n+15•Vid]
configuration

Show room X1), preset X( video configuration. Show the input (X!) tied to 16 sequential outputs assigned to room X1), starting from output X@.

Command description:room #*room preset #*starting output # (StO#)*1(=video)VC

Response description:input # (I#) tied to StO#•I# tied to StO#+1• ... •I# tied to StO#+15•Vid]

NOTE: The starting output number (X@) should always be “1” for matrix sizes of 16 outputs or smaller.

View audio room preset	EX1)*X(*X@*2VC}	X!n•X!n+1•...•X!n+15•Aud]
configuration

Show room X1), preset X( audio configuration. Show the input (X!) tied to 16 sequential outputs assigned to room X1), starting from output X@.

	Command description:	room #*room preset #*starting output # (StO#)*2(=audio)VC
	Response description:	input # (I#) tied to StO#•I# tied to StO#+1• ... •I# tied to StO#+15•Aud]
	NOTE: The starting output number (X@) should always be “1” for matrix sizes of 16 outputs or smaller.
Digital Sync Validation Processing (DSVP) (CrossPoint Switchers)
	List individual sync frequency	X$LS		X1#,X1#]		Listed as horizontal frequency, vertical
						frequency.
	Example:	2LS		031.50,060.00]		Input 2 horizontal frequency is 31.5 khZ
						and its vertical frequency is 60 Hz.
	NOTE: The matrix switcher returns 000.00,000.00 if there is no connection or sync frequencies are not applicable.
	View connections	0LS		X1$1X1$2X1$3...X1$n]		Each X1$ response is the connection
						status (0 = no input detected,
						1 = input detected) of an input, starting
						from input 1. n is the maximum
						number of inputs for this model.
RGB delay (CrossPoint) Switchers
	Set RGB delay	EX@*X1%D}		OutX@•DlyX1%*1]
	Example:	E13*7D}		Out13•Dly07]		Set the RGB interval for ties to output
						13 to 3.5 seconds (7 x 0.5 sec.).
	View RGB delay	EX@D}		X1%]
	Example:	E14D}		05]		Output 14 interval is 2.5 seconds
						(5 x 0.5 sec.).
NOTE: X! = Input number (for tie)			00 – (maximum number of inputs for your model)			(00 = untied)
	X@ = Output number		01 – (maximum number of outputs for your model)
	X$ = Input number (for other than tie)		01 – (maximum number of inputs for your model)
	X( = Global or room preset number		00 - 32, 10 maximum for a room preset (00 = current configuration for view only)
	X1) = Room number (for room presets)		10 max. (Each can have up to 10 presets (X(s) assigned.)
	X1# = Sync frequency		xxx.xx (frequency in Hz [V] or kHz [H])
	X1$ = Connection status		0 = no input connected		1 = input connected
	X1% = RGB delay interval		Delay in 1/2 second increments (10 maximum)

CrossPoint and MAV Series Matrix Switchers • Programming Guide 101