RS-232/RS-422 | Extron electronic 450 specification

RS-232/RS-422

HRemote RS-232/RS-422 connector — Connect a host device, such as a computer, touch panel control, or RS-232 capable PDA to the switcher via this 9-pin D connector for serial RS-232/RS-422 control (see figure 23).

REMOTE

1	6	RS232/RS422

5	9

			Matrix Sizes:
			84 through 1616		Matrix Sizes:
	All Models		MAV Plus 248 / 328 A		2412 through 3232
Pin	RS-232	Function	RS-422	Function	RS-422	Function
1	—	Not used	—	Not used	Tx+	Transmit data (+)
2	Tx	Transmit data	Tx–	Transmit data (–)	Tx–	Transmit data (–)
3	Rx	Receive data	Rx–	Receive data (–)	Rx+	Receive data (+)
4	—	Not used	—	Not used	Rx–	Receive data (–)
5	Gnd	Ground	Gnd	Ground	Gnd	Signal Ground
6	—	Not used	—	Not used	—	Not used
7	—	Not used	Rx+	Receive data (+)	—	Not used
8	—	Not used	Tx+	Transmit data (+)	—	Not used
9	—	Not used	—	Not used	—	Not used

Figure 23. Remote RS-232/RS-422 Connector

See Programming Guide, beginning on page 89, for definitions of the SIS commands (serial commands to control the switcher via this connector) and Matrix Software, beginning on page 110, for details on how to install and use the control software.

NOTE: The switcher can support either the RS-232 or RS-422 serial communication protocol, and operate at 9600, 19200, 38400, or 115200 baud rates. See Selecting the rear panel RS-232/RS-422 port protocol and baud rate on page 77, to configure the RS-232/RS-422 port from the front panel.

If desired, connect an MKP 2000 or MKP 3000 remote control panel to the RS-232/RS-422 connector on the switcher. See the MKP 2000 Remote Control Panel User Guide or the MKP 3000 Remote Control Panel User Guide for details.

CrossPoint and MAV Series Matrix Switchers • Installation 26

Image 32

Extron electronic 450 manual Remote RS-232/RS-422 Connector

Contents

User Guide Safety Instructions Safety Instructions English FCC Class a Notice Specifications Availability Software CommandsConventions Used in this Guide Notifications Contents Programming Guide Matrix SoftwareHtml Operation Ethernet Connection About the Crosspoint and MAV Matrix Switchers About this Guide Extron CrossPoint Ultra 128 HVA CrossPoint and MAV Series Matrix Switchers Introduction CrossPoint and MAV Series Matrix Switchers Introduction CrossPoint Ultra Switchers CrossPoint 450 Plus Switchers MAV Plus Switchers MAV 1616 Plus 16 inputs by 16 outputs Bandwidth FeaturesDefinitions Dsvp Data Display Tie any input to any or all outputs CrossPoint and MAV Series Matrix Switchers Introduction Setup and Installation Checklist Installation the switcher and make all connectionsGet ready Ancillary operations Rear Panel Views CrossPoint 450 Plus 3232 HVA Matrix Switcher CrossPoint Ultra 1616 HVA Matrix Switcher MAV Plus 3232 SVA Matrix Switcher MAV Plus 1616 HDA Matrix Switcher MAV Plus 1616 Matrix Switchers with Various Formats MAV Plus 128 AV RCA Matrix Switcher Video Input and Output Video Models Rgbhv CrossPoint switchersRear Panel Connections CrossPoint Ultra Video MAV Plus switchers MAV Plus Component/HDTV Video Connections MAV Plus S-video Connections MAV Plus Composite Video Connections Sync Termination Switches CrossPoint Sync Termination Switches Captive Screw Connector Wiring for Audio Inputs Audio Input and Output Audio Models RCA connector model MAV Plus 128 AV RCA Captive Screw Connector Wiring for Audio Output Remote RS-232/RS-422 Connector RS-232/RS-422 Ethernet Ethernet Reset Button External Sync MAV Plus Video Models Power Multiple Device External Sync Connection Example Front Panel Configuration Port Front Panel Configuration Port Front Panel Controls and Indicators Operation Comparison of Front Panels of Models Front panel, CrossPoint Ultra 128 HVA Crosspoint 450 Plus Series Input and Output Buttons CrossPoint CrossPoint and MAV Series Matrix Switchers Operation Control Buttons Audio CrossPoint and MAV Series Matrix Switchers Operation Controls Button Icons Power LEDs 2412 and Larger Models OnlyPrimary and Redundant Power Supply LEDs Front Panel Operations Definitions Front Panel Security Lockouts Creating a Configuration Example 1 Create a set of video and audio ties Select an input Press and release the input 5 button Final Configuration, Example Example 2 Add a video tie to a set of video and audio ties Example 3 Remove a tie from a set of ties 4 5 6 7 8 15 Viewing the Configuration Button lights red 18 19 20 21 22 23 24 Or background Grouping O Grouping of Incompatible Video Formats Press the View button to select group Press the Preset button to select groupPress the Enter button to select group Example 5 Grouping inputs and outputs Assign inputs and outputs to group Press and release the Input 5 through 8 buttons Setting RGB Delay CrossPoint Switchers Example 6 Setting the RGB delay for an output 3 4 5 6 7 8 15 23 24 31 Using Presets CrossPoint or MAV Plus 1600 Preset Locations Example 7 Saving a preset Seconds All input buttons with assigned Presets light Example 8 Recalling a preset 4 15 Muting and Unmuting Video and Audio Outputs Example 9 Muting and unmuting an audio output Select View-only Mute outputs one at a time Viewing and Adjusting the Input Audio Level Audio Models Audio Gain and Attenuation Output Button Audio Gain and Attenuation Display Matrix sizes Example 10 Viewing and adjusting an input audio level Select an Input Level Display on a 8-output-button Switcher Viewing and Adjusting the Analog Output Volume Audio Models Exit Audio mode Press and release the Audio button Reading the displayed volume Audio Volume Display CrossPoint and MAV Series Matrix Switchers Operation 10 11 13 14 15 10 11 Volume Display on a 16-input-button Switcher Setting the Front Panel Locks Executive Modes Selecting Lock mode 2 or toggling between mode 2 and mode Performing a System Reset from the Front Panel System Reset Background Illumination Selecting the Rear Panel Remote Port Protocol and Baud Rate Rear Panel Reset Operations Switcher model or Reset Resets MAV Plus switcher matrix size Reset Mode Comparison and Summary Mode Activation Result Performing Soft System Resets Resets 3, 4, Soft System Resets Performing Soft Resets Whole Switcher and Absolute Resets Performing a Hard Reset All Models Hard Reset Optimizing the Audio Audio Models TroubleshootingPlasma Display S-video Problem CrossPoint Switchers Configuration Worksheets Worksheet Example 1 System Equipment Worksheet Example 2 Daily Configuration Worksheet example 2 Daily Configuration Worksheet Example 3 Test Configuration Worksheet Example 3 Test Configuration Button switchers configuration worksheet Output destinations Audio Programming Guide Front Panel Configuration Port Serial PortsEthernet LAN Port Rear Panel RS-232/RS-422 Port Default IP addresses Connection TimeoutsEstablishing a Connection Number of Connections Using Verbose Mode Host-to-Switcher InstructionsSwitcher-initiated Messages Switcher Error Responses Symbol Definitions Using the Command and Response TablesCommand and Response Table for SIS Commands Command and Response Table for SIS Commands Command Function SIS Command Response Additional description Read ties Audio Volume Adjustment Settings Audio output volume Audio mutes View ties, gain, volume, mutes, and presets EX*X@*1VC NX!n+1...X!n+15Vid $LS EX11X12...X1nI GriX11X12X13...X1n Names Resets Information requests View and erase file directory X4! = IP and Remote port setup commands X5$ = Special Characters CrossPoint 450 Plus Software Operation via Ethernet Matrix Switchers Control ProgramEthernet protocol settings Installing the Software Software Operation via a Serial Port Using the Matrix Switcher Control Software Comm Port Selection Window Address and Password Entry Sample Program Window Icons Assigned and Ties Created IP Settings/Options window Control Program IP Setting/Options Window Use Dhcp check box Subnet mask Sync Time to PC button Mail Server IP Address field Mail Server Domain Name field Updating the Firmware Downloading Firmware Upgrade Files Ethernet-connected firmware upload Serial-port-connected firmware upload Uploading Html Files Html Files List Window File menu Windows Buttons, Drop Boxes, and Trash CanWindows Menus Tools menu Status Window Audio-input Configuration selection Preferences menu Using Emulation Mode Master-Reset selection Using the Help System Emulate Configuration Dialog Box Installing the Button Label Generator Software Button-Label Generator Program Using the Button-Label Generator Software Extron Button-Label Generator Window Html Operation Enter Network Password Dialog Box Download the Startup Not displayed for the CrossPoint or MAV Status TabSystem Status System Settings Configuration TabDsvp Page CrossPoint Switchers IP Settings fields Unit Name field Date/Time Settings fields Date/Time Settings Fields Passwords Resetting a password Email Settings Mail IP Address field Deselecting Smtp authorization Firmware Upgrade Firmware Upgrade File Management Tab File Management Amber buttons indicate video and audio ties Control TabSet and View Ties RGB and Audio Settings RGB and Audio Settings Change the input gain and attenuation audio models Input Selection Drop Box Change the RGB delay CrossPoint switchers Mute and unmute one or all outputs Change the output volume level audio models RGB Delay Drop Box Number Output Steps Attenuation Volume Recalling a preset Global PresetsSaving a preset Ethernet Connection Default IP AddressEthernet Link Pinging to Determine the Extron IP Address Pinging to Determine the Web IP Address Ping with New Address Open Connecting as a Telnet ClientTelnet Tips Escape character and Esc key Analog echoSet carriage return-line feed Close Subnetting a Primer GatewaysAnalog and Remote Devices IP Addresses and Octets Subnet Masks and Octets Determining Whether Devices Are on the Same SubnetUnmasked octets are compared indicated by ? in figure Masked octets are not compared indicated by X in figure Mounting the Switcher Reference Information UL Guidelines Mounting Instructions Making Labels from Paper Templates Removing and Installing Button LabelsInstalling Labels in the Buttons Button Label Blanks Extron Warranty