![](/images/new-backgrounds/1109261/109261155x1.webp)
Example 11: Viewing and adjusting a analog output volume level
In the following example, the audio output volume is viewed and adjusted. The steps show the front panel indications that result from your action.
Audio output volume is displayed differently on different models (see table 4 on page 70).
Because of the different volume display schemes, the output audio levels that result from the following example are shown three times:
•As displayed on a
•As displayed on a
•As displayed on a
The
1.Clear all selections: Press and release the Esc button.
2.Select Audio mode: Press and hold the Audio button for approximately 2 seconds until it blinks.
AUDIO
Press and hold the Audio button until it blinks.
2 seconds
AUDIO
3.Select an output: Press and release the output 1 button (see figure 45).
In figure 45, figure 46, and figure 47, the lit or blinking input buttons indicate 41.5 percent of the applied audio input. The unlit input buttons indicate an audio volume attenuation of 39 dB.
The input buttons display the audio volume level of the selected output.
Blinking button
•
• 41.5% volume
Press and release the Output 1 button. The button lights green.
1 | 2 | O | |
U | |||
T | |||
|
| ||
|
| P | |
17 | 18 | U | |
T | |||
S | |||
|
|
![](/images/new-backgrounds/1109261/109261155xi2.webp)
![](/images/new-backgrounds/1109261/109261155xi3.webp)
1 ![](/images/new-backgrounds/1109261/109261155xi5.webp)
![](/images/new-backgrounds/1109261/109261155xi6.webp)
![](/images/new-backgrounds/1109261/109261155xi7.webp)
2 ![](/images/new-backgrounds/1109261/109261155xi9.webp)
![](/images/new-backgrounds/1109261/109261155xi10.webp)
![](/images/new-backgrounds/1109261/109261155xi11.webp)
3 ![](/images/new-backgrounds/1109261/109261155xi13.webp)
![](/images/new-backgrounds/1109261/109261155xi14.webp)
![](/images/new-backgrounds/1109261/109261155xi15.webp)
![](/images/new-backgrounds/1109261/109261155xi16.webp)
![](/images/new-backgrounds/1109261/109261155xi17.webp)
![](/images/new-backgrounds/1109261/109261155xi18.webp)
![](/images/new-backgrounds/1109261/109261155xi19.webp)
12![](/images/new-backgrounds/1109261/109261155xi21.webp)
![](/images/new-backgrounds/1109261/109261155xi22.webp)
![](/images/new-backgrounds/1109261/109261155xi23.webp)
13 ![](/images/new-backgrounds/1109261/109261155xi25.webp)
![](/images/new-backgrounds/1109261/109261155xi26.webp)
![](/images/new-backgrounds/1109261/109261155xi27.webp)
14 ![](/images/new-backgrounds/1109261/109261155xi29.webp)
![](/images/new-backgrounds/1109261/109261155xi30.webp)
![](/images/new-backgrounds/1109261/109261155xi31.webp)
15 ![](/images/new-backgrounds/1109261/109261155xi33.webp)
![](/images/new-backgrounds/1109261/109261155xi34.webp)
![](/images/new-backgrounds/1109261/109261155xi35.webp)
16 ![](/images/new-backgrounds/1109261/109261155xi37.webp)
![](/images/new-backgrounds/1109261/109261155xi38.webp)
![](/images/new-backgrounds/1109261/109261155xi39.webp)
17
18
19
28
29
30
31
32
I
N P U T S
Each lit input button beyond input 1 indicates 3 percent of the total input volume is applied to the output. The flashing button indicates an additional 1.5 percent.
In this example, the lit input buttons indicate 41.5 percent of the applied audio input. The unlit input buttons indicate an audio volume attenuation of 39 dB.
Figure 45. Select Output 1
Figure 46 shows the same volume (41.5%) as figure 45, but displayed on a 16-input- button switcher, such as a MAV Plus 1616 HDA.
|
|
|
|
| Blinking button |
|
|
| ||
|
|
|
|
|
|
|
| |||
|
|
|
|
| 41.5% volume |
|
|
| ||
|
|
|
|
|
|
| INPUTS |
|
| |
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 11 12 | 13 14 15 16 |
•The input LEDs display the selected output's audio volume level.
•In this example, the lit or blinking input buttons indicate 41.5 to 44.5 percent of the applied audio input.
•The unlit or blinking input buttons indicate an audio volume attenuation of 37 dB to 39 dB.