Programming Guide | Extron electronic 450 manual

Programming

Guide

The CrossPoint and MAV Plus matrix switchers can be remotely controlled via:

•The Matrix Switchers Control Program (see the Matrix Software, beginning on page 110)

•Built-in HMTL pages (see HTML Operation, beginning on page 131)

•SIS commands (see below)

This section describes the operation of the CrossPoint and MAV Plus matrix switchers via SIS commands, including:

•Serial Ports

•Ethernet (LAN) Port

•Host-to-Switcher Instructions

•Switcher-Initiated Messages

•Switcher Error Responses

•Using the Command and Response Tables

•Command and Response Table for SIS Commands

•SIS Command and Response Table for IP- and Remote Port-Specific Commands

•Special Characters

CrossPoint and MAV Series Matrix Switchers • Programming Guide 89

Image 95

Extron electronic 450 manual Programming Guide

Contents

User Guide Safety Instructions English Safety Instructions FCC Class a Notice Notifications Specifications AvailabilitySoftware Commands Conventions Used in this Guide Contents Ethernet Connection Programming GuideMatrix Software Html Operation About this Guide About the Crosspoint and MAV Matrix Switchers Extron CrossPoint Ultra 128 HVA CrossPoint and MAV Series Matrix Switchers Introduction CrossPoint and MAV Series Matrix Switchers Introduction CrossPoint Ultra Switchers MAV Plus Switchers CrossPoint 450 Plus Switchers MAV 1616 Plus 16 inputs by 16 outputs Bandwidth FeaturesDefinitions Dsvp Data Display Tie any input to any or all outputs CrossPoint and MAV Series Matrix Switchers Introduction Ancillary operations Setup and Installation ChecklistInstallation the switcher and make all connections Get ready Rear Panel Views CrossPoint 450 Plus 3232 HVA Matrix Switcher CrossPoint Ultra 1616 HVA Matrix Switcher MAV Plus 3232 SVA Matrix Switcher MAV Plus 1616 Matrix Switchers with Various Formats MAV Plus 1616 HDA Matrix Switcher MAV Plus 128 AV RCA Matrix Switcher Video Input and Output Video Models Rgbhv CrossPoint switchersRear Panel Connections CrossPoint Ultra MAV Plus Component/HDTV Video Connections Video MAV Plus switchers MAV Plus Composite Video Connections MAV Plus S-video Connections Sync Termination Switches Sync Termination Switches CrossPoint Audio Input and Output Audio Models Captive Screw Connector Wiring for Audio Inputs Captive Screw Connector Wiring for Audio Output RCA connector model MAV Plus 128 AV RCA RS-232/RS-422 Remote RS-232/RS-422 Connector Ethernet Ethernet External Sync MAV Plus Video Models Reset Button Multiple Device External Sync Connection Example Power Front Panel Configuration Port Front Panel Configuration Port Operation Front Panel Controls and Indicators Front panel, CrossPoint Ultra 128 HVA Comparison of Front Panels of Models Crosspoint 450 Plus Series CrossPoint Input and Output Buttons CrossPoint and MAV Series Matrix Switchers Operation Audio Control Buttons CrossPoint and MAV Series Matrix Switchers Operation Controls Button Icons Power LEDs 2412 and Larger Models OnlyPrimary and Redundant Power Supply LEDs Definitions Front Panel Operations Front Panel Security Lockouts Creating a Configuration Select an input Press and release the input 5 button Example 1 Create a set of video and audio ties Example 2 Add a video tie to a set of video and audio ties Final Configuration, Example Example 3 Remove a tie from a set of ties 4 5 6 7 8 15 Viewing the Configuration Button lights red 18 19 20 21 22 23 24 Or background O Grouping of Incompatible Video Formats Grouping Press the View button to select group Press the Preset button to select groupPress the Enter button to select group Assign inputs and outputs to group Example 5 Grouping inputs and outputs Press and release the Input 5 through 8 buttons Example 6 Setting the RGB delay for an output Setting RGB Delay CrossPoint Switchers 3 4 5 6 7 8 15 23 24 31 CrossPoint or MAV Plus 1600 Preset Locations Using Presets Seconds All input buttons with assigned Presets light Example 7 Saving a preset 4 15 Example 8 Recalling a preset Muting and Unmuting Video and Audio Outputs Select View-only Example 9 Muting and unmuting an audio output Mute outputs one at a time Audio Gain and Attenuation Viewing and Adjusting the Input Audio Level Audio Models Output Button Audio Gain and Attenuation Display Matrix sizes Select an Input Example 10 Viewing and adjusting an input audio level Level Display on a 8-output-button Switcher Exit Audio mode Press and release the Audio button Viewing and Adjusting the Analog Output Volume Audio Models Reading the displayed volume Audio Volume Display CrossPoint and MAV Series Matrix Switchers Operation 10 11 13 14 15 10 11 Volume Display on a 16-input-button Switcher Selecting Lock mode 2 or toggling between mode 2 and mode Setting the Front Panel Locks Executive Modes System Reset Performing a System Reset from the Front Panel Selecting the Rear Panel Remote Port Protocol and Baud Rate Background Illumination Switcher model or Reset Resets MAV Plus switcher matrix size Rear Panel Reset Operations Mode Activation Result Reset Mode Comparison and Summary Soft System Resets Performing Soft System Resets Resets 3, 4, Whole Switcher and Absolute Resets Performing Soft Resets Hard Reset Performing a Hard Reset All Models Optimizing the Audio Audio Models TroubleshootingPlasma Display S-video Problem CrossPoint Switchers Worksheet Example 1 System Equipment Configuration Worksheets Worksheet example 2 Daily Configuration Worksheet Example 2 Daily Configuration Worksheet Example 3 Test Configuration Worksheet Example 3 Test Configuration Output destinations Button switchers configuration worksheet Audio Programming Guide Rear Panel RS-232/RS-422 Port Front Panel Configuration PortSerial Ports Ethernet LAN Port Number of Connections Default IP addressesConnection Timeouts Establishing a Connection Using Verbose Mode Host-to-Switcher InstructionsSwitcher-initiated Messages Switcher Error Responses Symbol Definitions Using the Command and Response TablesCommand and Response Table for SIS Commands Command Function SIS Command Response Additional description Command and Response Table for SIS Commands Read ties Audio output volume Audio Volume Adjustment Settings Audio mutes View ties, gain, volume, mutes, and presets EX*X@*1VC NX!n+1...X!n+15Vid $LS EX11X12...X1nI GriX11X12X13...X1n Names Resets Information requests View and erase file directory X4! = X5$ = IP and Remote port setup commands CrossPoint 450 Plus Special Characters Software Operation via Ethernet Matrix Switchers Control ProgramEthernet protocol settings Software Operation via a Serial Port Installing the Software Comm Port Selection Window Using the Matrix Switcher Control Software Address and Password Entry Sample Program Window Icons Assigned and Ties Created Control Program IP Setting/Options Window IP Settings/Options window Subnet mask Use Dhcp check box Sync Time to PC button Mail Server Domain Name field Mail Server IP Address field Updating the Firmware Downloading Firmware Upgrade Files Ethernet-connected firmware upload Serial-port-connected firmware upload Html Files List Window Uploading Html Files File menu Windows Buttons, Drop Boxes, and Trash CanWindows Menus Status Window Tools menu Preferences menu Audio-input Configuration selection Master-Reset selection Using Emulation Mode Emulate Configuration Dialog Box Using the Help System Button-Label Generator Program Installing the Button Label Generator Software Extron Button-Label Generator Window Using the Button-Label Generator Software Html Operation Download the Startup Enter Network Password Dialog Box Not displayed for the CrossPoint or MAV Status TabSystem Status System Settings Configuration TabDsvp Page CrossPoint Switchers Unit Name field IP Settings fields Date/Time Settings Fields Date/Time Settings fields Resetting a password Passwords Mail IP Address field Email Settings Deselecting Smtp authorization Firmware Upgrade Firmware Upgrade File Management File Management Tab Amber buttons indicate video and audio ties Control TabSet and View Ties RGB and Audio Settings RGB and Audio Settings Input Selection Drop Box Change the input gain and attenuation audio models Mute and unmute one or all outputs Change the RGB delay CrossPoint switchers RGB Delay Drop Box Change the output volume level audio models Number Output Steps Attenuation Volume Recalling a preset Global PresetsSaving a preset Ethernet Connection Default IP AddressEthernet Link Pinging to Determine the Web IP Address Pinging to Determine the Extron IP Address Ping with New Address Open Connecting as a Telnet ClientTelnet Tips Close Escape character and Esc keyAnalog echo Set carriage return-line feed IP Addresses and Octets Subnetting a PrimerGateways Analog and Remote Devices Masked octets are not compared indicated by X in figure Subnet Masks and OctetsDetermining Whether Devices Are on the Same Subnet Unmasked octets are compared indicated by ? in figure Reference Information Mounting the Switcher Mounting Instructions UL Guidelines Making Labels from Paper Templates Removing and Installing Button LabelsInstalling Labels in the Buttons Button Label Blanks Extron Warranty