Controls | Extron electronic 450 guide

I/O Controls

NOTE: See Front Panel Operations, beginning on page 40 for detailed descriptions of the following operations.

Primary functions

	Action	Select video	Select audio

	Indication	Green: selected	Red: selected

RGBHV	VIDEO	AUDIO
	or

Secondary functions

Front panel	Action 1	With Enter, select Lock mode 2 or toggle
locks		between mode 0 and mode 2.

	Action 2	Select Lock mode 1 or toggle between mode 2
		and mode 1.

RGB Delay	Action/	Select RGB Delay mode.
	indication	Blinks green.

Resets	Action 1	Perform a system reset.

Port	Action	Select RS-232.	Select RS-422
configuration	Indication	Blink: selected	Blink: selected
Audio	Action		Select Audio mode.

You must specify video, audio, or both when you are creating or viewing a configuration. This is done with the RGBHV button (CrossPoint switchers) or Video button (MAV Plus switchers) (G) and Audio (H) buttons.

GRGBHV (CrossPoint) button or Video (MAV Plus) button — The RGBHV (CrossPoint switchers) or Video (MAV Plus switchers) button has one primary function (❏) and five secondary functions (•):

❏Selects and deselects video for a configuration that is being created or viewed and lights green to indicate that video is available for configuring or for viewing.

•With the Enter button and Audio button, selects between front panel locks (Lock mode 2 and Lock mode 0).

•With the Audio button, commands the front panel system reset.

•(CrossPoint switchers) Selects the RGB delay mode, in which you can set the RGB delay.

•Selects the RS-232 protocol for the rear panel Remote port in Serial Port Selection and Configuration mode and indicates the selection.

CrossPoint and MAV Series Matrix Switchers • Operation 38

Image 44

Extron electronic 450 manual Controls

Contents

User Guide Safety Instructions Safety Instructions English FCC Class a Notice Specifications Availability Software CommandsConventions Used in this Guide Notifications Contents Programming Guide Matrix SoftwareHtml Operation Ethernet Connection About the Crosspoint and MAV Matrix Switchers About this Guide Extron CrossPoint Ultra 128 HVA CrossPoint and MAV Series Matrix Switchers Introduction CrossPoint and MAV Series Matrix Switchers Introduction CrossPoint Ultra Switchers CrossPoint 450 Plus Switchers MAV Plus Switchers MAV 1616 Plus 16 inputs by 16 outputs Bandwidth FeaturesDefinitions Dsvp Data Display Tie any input to any or all outputs CrossPoint and MAV Series Matrix Switchers Introduction Setup and Installation Checklist Installation the switcher and make all connectionsGet ready Ancillary operations Rear Panel Views CrossPoint 450 Plus 3232 HVA Matrix Switcher CrossPoint Ultra 1616 HVA Matrix Switcher MAV Plus 3232 SVA Matrix Switcher MAV Plus 1616 HDA Matrix Switcher MAV Plus 1616 Matrix Switchers with Various Formats MAV Plus 128 AV RCA Matrix Switcher Video Input and Output Video Models Rgbhv CrossPoint switchersRear Panel Connections CrossPoint Ultra Video MAV Plus switchers MAV Plus Component/HDTV Video Connections MAV Plus S-video Connections MAV Plus Composite Video Connections Sync Termination Switches CrossPoint Sync Termination Switches Captive Screw Connector Wiring for Audio Inputs Audio Input and Output Audio Models RCA connector model MAV Plus 128 AV RCA Captive Screw Connector Wiring for Audio Output Remote RS-232/RS-422 Connector RS-232/RS-422 Ethernet Ethernet Reset Button External Sync MAV Plus Video Models Power Multiple Device External Sync Connection Example Front Panel Configuration Port Front Panel Configuration Port Front Panel Controls and Indicators Operation Comparison of Front Panels of Models Front panel, CrossPoint Ultra 128 HVA Crosspoint 450 Plus Series Input and Output Buttons CrossPoint CrossPoint and MAV Series Matrix Switchers Operation Control Buttons Audio CrossPoint and MAV Series Matrix Switchers Operation Controls Button Icons Power LEDs 2412 and Larger Models OnlyPrimary and Redundant Power Supply LEDs Front Panel Operations Definitions Front Panel Security Lockouts Creating a Configuration Example 1 Create a set of video and audio ties Select an input Press and release the input 5 button Final Configuration, Example Example 2 Add a video tie to a set of video and audio ties Example 3 Remove a tie from a set of ties 4 5 6 7 8 15 Viewing the Configuration Button lights red 18 19 20 21 22 23 24 Or background Grouping O Grouping of Incompatible Video Formats Press the View button to select group Press the Preset button to select groupPress the Enter button to select group Example 5 Grouping inputs and outputs Assign inputs and outputs to group Press and release the Input 5 through 8 buttons Setting RGB Delay CrossPoint Switchers Example 6 Setting the RGB delay for an output 3 4 5 6 7 8 15 23 24 31 Using Presets CrossPoint or MAV Plus 1600 Preset Locations Example 7 Saving a preset Seconds All input buttons with assigned Presets light Example 8 Recalling a preset 4 15 Muting and Unmuting Video and Audio Outputs Example 9 Muting and unmuting an audio output Select View-only Mute outputs one at a time Viewing and Adjusting the Input Audio Level Audio Models Audio Gain and Attenuation Output Button Audio Gain and Attenuation Display Matrix sizes Example 10 Viewing and adjusting an input audio level Select an Input Level Display on a 8-output-button Switcher Viewing and Adjusting the Analog Output Volume Audio Models Exit Audio mode Press and release the Audio button Reading the displayed volume Audio Volume Display CrossPoint and MAV Series Matrix Switchers Operation 10 11 13 14 15 10 11 Volume Display on a 16-input-button Switcher Setting the Front Panel Locks Executive Modes Selecting Lock mode 2 or toggling between mode 2 and mode Performing a System Reset from the Front Panel System Reset Background Illumination Selecting the Rear Panel Remote Port Protocol and Baud Rate Rear Panel Reset Operations Switcher model or Reset Resets MAV Plus switcher matrix size Reset Mode Comparison and Summary Mode Activation Result Performing Soft System Resets Resets 3, 4, Soft System Resets Performing Soft Resets Whole Switcher and Absolute Resets Performing a Hard Reset All Models Hard Reset Optimizing the Audio Audio Models TroubleshootingPlasma Display S-video Problem CrossPoint Switchers Configuration Worksheets Worksheet Example 1 System Equipment Worksheet Example 2 Daily Configuration Worksheet example 2 Daily Configuration Worksheet Example 3 Test Configuration Worksheet Example 3 Test Configuration Button switchers configuration worksheet Output destinations Audio Programming Guide Front Panel Configuration Port Serial PortsEthernet LAN Port Rear Panel RS-232/RS-422 Port Default IP addresses Connection TimeoutsEstablishing a Connection Number of Connections Using Verbose Mode Host-to-Switcher InstructionsSwitcher-initiated Messages Switcher Error Responses Symbol Definitions Using the Command and Response TablesCommand and Response Table for SIS Commands Command and Response Table for SIS Commands Command Function SIS Command Response Additional description Read ties Audio Volume Adjustment Settings Audio output volume Audio mutes View ties, gain, volume, mutes, and presets EX*X@*1VC NX!n+1...X!n+15Vid $LS EX11X12...X1nI GriX11X12X13...X1n Names Resets Information requests View and erase file directory X4! = IP and Remote port setup commands X5$ = Special Characters CrossPoint 450 Plus Software Operation via Ethernet Matrix Switchers Control ProgramEthernet protocol settings Installing the Software Software Operation via a Serial Port Using the Matrix Switcher Control Software Comm Port Selection Window Address and Password Entry Sample Program Window Icons Assigned and Ties Created IP Settings/Options window Control Program IP Setting/Options Window Use Dhcp check box Subnet mask Sync Time to PC button Mail Server IP Address field Mail Server Domain Name field Updating the Firmware Downloading Firmware Upgrade Files Ethernet-connected firmware upload Serial-port-connected firmware upload Uploading Html Files Html Files List Window File menu Windows Buttons, Drop Boxes, and Trash CanWindows Menus Tools menu Status Window Audio-input Configuration selection Preferences menu Using Emulation Mode Master-Reset selection Using the Help System Emulate Configuration Dialog Box Installing the Button Label Generator Software Button-Label Generator Program Using the Button-Label Generator Software Extron Button-Label Generator Window Html Operation Enter Network Password Dialog Box Download the Startup Not displayed for the CrossPoint or MAV Status TabSystem Status System Settings Configuration TabDsvp Page CrossPoint Switchers IP Settings fields Unit Name field Date/Time Settings fields Date/Time Settings Fields Passwords Resetting a password Email Settings Mail IP Address field Deselecting Smtp authorization Firmware Upgrade Firmware Upgrade File Management Tab File Management Amber buttons indicate video and audio ties Control TabSet and View Ties RGB and Audio Settings RGB and Audio Settings Change the input gain and attenuation audio models Input Selection Drop Box Change the RGB delay CrossPoint switchers Mute and unmute one or all outputs Change the output volume level audio models RGB Delay Drop Box Number Output Steps Attenuation Volume Recalling a preset Global PresetsSaving a preset Ethernet Connection Default IP AddressEthernet Link Pinging to Determine the Extron IP Address Pinging to Determine the Web IP Address Ping with New Address Open Connecting as a Telnet ClientTelnet Tips Escape character and Esc key Analog echoSet carriage return-line feed Close Subnetting a Primer GatewaysAnalog and Remote Devices IP Addresses and Octets Subnet Masks and Octets Determining Whether Devices Are on the Same SubnetUnmasked octets are compared indicated by ? in figure Masked octets are not compared indicated by X in figure Mounting the Switcher Reference Information UL Guidelines Mounting Instructions Making Labels from Paper Templates Removing and Installing Button LabelsInstalling Labels in the Buttons Button Label Blanks Extron Warranty