Soft Resets | Extron electronic DXP DVI PRO guide

To perform a soft reset of the switcher:

1.Use a small Philips screwdriver to press and hold the rear panel Reset button until the front panel Video and Audio buttons blink once (for an events reset), twice (for a system reset), or three times (for an absolute reset).

Press and hold the Reset button.

Events Reset	RESET
Events Reset
(Mode 3)

Reset LED flashes once.

3 seconds	RESET

Release, then immediately press and release again.

RESET

Front panel I/O buttons flash once.

I / O

VIDEO

AUDIO

Press and hold	Reset LED flashes twice.
the Reset button.

IP Settings	RESET	6 seconds	RESET
IP Settings		6 seconds
Reset
(Mode 4)

Release, then immediately press and release again.

RESET

Front panel I/O buttons flash twice.

I / O

VIDEO

AUDIO

Press and hold the Reset button.

Absolute Reset	RESET
Absolute Reset
(Mode 5)

Reset LED flashes

three times.

9 seconds	RESET

Release, then immediately press and release again.

RESET

Front panel I/O buttons flash three times.

I / O

VIDEO

AUDIO

Figure 62. Soft Resets

2.Release the Reset button and then immediately press and release the Reset button again. Nothing happens if the second momentary press does not occur within

1 second.

DXP DVI, DXP DVI Pro, and DXP HDMI Series • Operation

43

Image 49

Extron electronic DXP DVI PRO manual Soft Resets

Contents

DXP DVI Safety Instructions English FCC Class a Notice Specifications Availability Conventions Used in this Guide Software CommandsNotifications Contents 122 105 DXP DVI Series non-Pro About this GuideDXP DVI Pro Series DXP DVI and DXP DVI Pro Series FeaturesDXP Hdmi Series DXP DVI, DXP DVI Pro, and DXP Hdmi Rack-mountable 2U, full rack width metal enclosure Application Diagram for a DXP 88 Hdmi Application Diagrams Application Diagram for a DXP 88 DVI Pro Application Diagram for a DXP 88 DVI Non-Pro DXP 88 DVI Pro Rear Panel Rear Panels DVI Connector Pin Assignments Input connectors Output connectors Straight-through Cable Pin End Wire Color Wire ColorConnections Ethernet Connection Remote RS232/RS422 Connector Pin Assignments RS-232 Config port front panelRS-232 and RS-422 Remote Connections Remote RS232/RS422 port rear panel Definitions Operation DXP Switchers Front Panel Front Panel Controls and Indicators Input and Output Buttons Setting the Button Background Illumination on Control Buttons Configuration Port Secondary functions Buttons Example of Button Labels on a DXP Front Panel Button Icons Creating a Configuration Powering On Clear All Selections Example 1 Creating a Set of Ties Select Input Select Video Only Example 2 Adding a Tie to a Set of Video Ties Confirm the Tie Breaking Ties Select Audio Only Example 3 Removing a Tie from a Set of Ties Confirm the Tie Removal Viewing a Configuration Press the Esc button to clear all selections Select an Input to View Deselect Audio and Select Video to View Only Video Ties Example 5 Saving a Preset Saving and Recalling Presets Enter Save Preset Mode Example 6 Recalling a Preset Enter Recall Preset Mode O Grouping of Incompatible Video Formats Grouping Group # Example 7 Grouping Inputs and Outputs Select I/O Group Mode Assign Inputs and Outputs to Group Muting and Unmuting Video and Audio Outputs Deselect I/O Group Mode Example 8 Muting and Unmuting an Output Mute the Outputs Locking and Unlocking the Front Panel Executive Modes Selecting Lock Mode 2 or Toggling Between Mode 2 and Mode Switching from Lock Mode 1 to Lock Mode ResettingResetting the System from the Front Panel System Reset Resetting Using the Rear Panel Reset Button Mode Activation Result Purpose/Notes Reset Modes Summary Soft Resets Toggle Background Illumination On or Off Setting the Button Background Illumination RS-232/RS-422 and Baud Rate Selection Troubleshooting Worksheet Example 1 System Equipment Configuration Worksheets Worksheet Example 3 Test Configuration Worksheet Example 2 Daily Configuration Input Sources Output Destinations Worksheet Form Serial Ports SIS Configuration Control Ethernet Port Default IP AddressesEthernet Cable Establishing an Ethernet Connection Switcher-initiated Messages Host-to-Switcher InstructionsConnection Timeouts Verbose Mode Password Using the Command and Response Tables for SIS Commands Switcher Error ResponsesSpecial Characters Symbol Definitions for DXP SIS Commands for DXPX1# X1$ X2# X2$ DXP DVI, DXP DVI Pro, and DXP Hdmi DXP DVI Pro and Hdmi Edid Table DDC Source Selection @ *X# $ Command and Response Table for DXP SIS Commands+Q X@ *X# %...X@ *X# @ *% Save, Recall, and Directly Write Global and Room Presets Mute Commands# B # Z +X& PO + X& P X@*X#!X@*X# % X@*X#$...X@*X#X# ,X# , ...X# n MR Mpr X ,X# ,X# , ...X# n X1# X ,X# ,X# , ...X# n +X*X* P X@*X#!X@*X#%X@*X#$...X@*X# View Ties and Presets@X@...X@Vid DXP 88 Hdmi @X@...X@Aud % X%...X% O % X%... X%nIGro X% X% X%...X%n Digital Sync Validation Processing Dsvp 2NG X1# NG Nmg X&,X1#X1# NR Nmr X,X1# X* ,X1# NP Nmp X *X* ,X1# Resets Hdcp Authorization DXP DVI Pro and Hdmi models onlyX* ZP Information Requests Firmware Version Queries X1X1X1&X1*X$ X!*X1 Edid Edid Extended Display Identification Data CommandsX1 EDIDX2 X1 . X1 = 37 X1 X1...X1n Hdcp Query Commands Symbol Definitions for IP-specific Commands IP-specific SIS CommandsX3@ X3# X3$ X3% X4# X5# X4$X5$ X5% Command and Response Table for IP-Specific SIS Commands X4 DH X4# X4!,X4$,X4% EM Ipe X4# X4!*X4$*X4% X4%...X4%X4&*X4*,X4,X5,X5! CP Cpn X4&Ccp X4*,X4,X5,X5 Installing the Software Matrix Switchers Control Program Ethernet protocol settings Using the SoftwareSoftware Operation Via Ethernet Baud Rate Pop-up List Extron Matrix Switcher Control Program Matrix Window No Ties Sample Matrix Window with Ties Setting Up the Matrix Window Pop-up Window for Input 4 Containing a Caption Managing Ties Matrix Window with Pop-up Information on Audio Input IP Settings/Options Window IP Setup Setting the Extron name or descriptor Setting the IP addressSetting the gateway IP address Setting the date Setting the subnet maskHardware Address field Enabling and disabling Dhcp Setting the offset from GMT Setting the local timeSetting the administrator password Sync Time to PC button Setting the mail server IP address Setting the user passwordSetting the mail server domain name Typical DXP E-mail Entering e-mail addressee information Updating the Firmware Select Files to Upload Window with Firmware File Selected Html Files List Window Uploading Html Files Window Menus Window Buttons, Menus, and Trash Can Right ColumnFile menu Devices Window Tools menu Channel Mute Settings Window Edid Record Viewer Uploading Html Files on Names for Presets Window Input/Output Groups Window Room Configuration Window Ties Shown as Lines Preferences menu Ties Shown as Crosspoints O Boxes Containing the Input and Output Numbers Master-Reset button Help menu Using Emulation ModeIP Connection Selecting an Emulation File Creating Button Labels Using the Matrix Switcher Help File Button Label Generator Window Using the Button Label Generator Replacing a Button Label Replacing Button Labels Blank Button Labels Html Operation Accessing the Web Pages Special Characters Example of a Network Password Dialog Box System Status Status Tab Dsvp and Hdcp Page for the DXP DVI Pro and DXP Hdmi Dsvp and Hdcp System Settings Configuration Tab Unit Name field IP Settings Fields Date/Time Settings Fields Date/Time Settings Fields Entering a password PasswordsClearing a password Mail IP Address field Email Settings Domain Name field Smtp Authorization Required fieldsEmail address fields Email Options Menu on the Email Settings Firmware Upgrade Choose File Window with a Firmware File Selected Uploading Files File Management Tab Other File Management Activities Adding a Directory Set and View Ties Control Tab Pop-up Field Providing Formation About a Button Tie Saving a preset Global PresetsRecalling a preset Included Part Replacement Part Number Part Numbers and AccessoriesModels Included Parts Optional Accessories Mounting the SwitcherCables and Adapters UL Guidelines for Rack Mounting Rack Mounting the DXP to a 19-inch Rack Rack Mounting Procedure IP Addressing What is an IP Address?Choosing IP Addresses Class Name Valid Address Range Identifier Arrangement Pinging for the IP Address Subnet MaskPing to determine Extron IP address Class Name Subnet Mask Ping to determine web IP address Connecting as a Telnet ClientStarting Telnet Connecting to the DXP Open command Operating using Telnet Gateways Subnetting, a PrimerLocal and remote devices IP addresses and octets Determining whether devices are on the same subnet Subnet masks and octetsUnmasked octets are compared indicated by ? in figure Masked octets are not compared indicated by n in figure Extron Warranty