Chapter 2 How to Load Documents
Loading Capacity
The number of sheets that can be loaded in the ADF paper chute is determined by the paper size and paper weight of the document. See the graph below.
|
|
|
|
|
|
|
| A4/Letter or smaller |
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
| Legal |
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
| 60 |
|
|
|
| 60 |
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| 50 |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
(sheets) | 50 |
|
|
|
| 50 |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
40 |
|
|
|
|
|
|
|
|
|
|
| 35 |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| 41 |
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Capacity |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
30 |
|
|
|
|
|
|
|
|
|
|
|
| 29 |
|
| 29 |
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 24 |
|
| ||
| 20 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 52 | 64 |
| 80 |
| 104 |
| 127 |
| ||||||||||
|
|
|
|
|
| Paper weight (g/m2) |
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
Paper weight |
|
|
|
|
| Conversion |
|
|
|
|
|
| |||||||||
| (unit) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
g/m2 | 52 |
| 64 |
|
| 75 |
| 80 | 90 |
| 104 |
|
| 127 |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
lb |
|
|
| 14 |
| 17 |
|
| 20 |
| 21 | 24 |
| 28 |
|
| 34 |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
kg |
|
|
| 45 |
| 55 |
|
| 64.5 |
| 69 | 77.5 | 90 |
|
| 110 |
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Area Not to Be Perforated
An error may occur when there are punched holes in the area
shaded in light blue in the following picture.
Reference point | 50 |
|
Top
Front side
Feed direction
Bottom
Center of document( Unit : mm)
The above condition applies when the document is set to the ！ center of the pick roller width.
If there are any holes in the 50
32