Chapter 5 Various Ways to Scan
Operational procedure | 4 Press the [Function] button and confirm that the function | ||||||||
1 After a multifeed error occurs, open the ADF and remove |
| number is flashing faster, then either press the [Scan/Stop] | |||||||
| button or perform a scan from the computer. | ||||||||
| the documents. |
| |||||||
|
| From this point, the flashing speed of the Function Number Display | |||||||
|
|
|
|
|
|
|
|
| |
2 Close the ADF. |
| switches between “slow” Q “fast” every time you press the [Function] | |||||||
| button. When the flashing speed is fast, the scanner operates in each | ||||||||
| For details, refer to "1.4 Opening/Closing the ADF" (page 19). |
| mode as follows: | ||||||
| When the ADF is closed, the Function Number Display on the |
|
| ||||||
| operator panel changes as follows: |
| Do not press down the [Function] button for more than five | ||||||
|
|
|
|
|
|
|
|
| |
| z Upon multifeed error |
| ！ seconds when switching the flashing speed, because it | ||||||
|
| Alternates between “J” and “2” |
| may erase the memorized multifeed patterns. | |||||
| z Upon ejecting the documents |
|
| ||||||
|
|
| |||||||
|
| The function number flashes |
| z Manual mode (Bypass by front panel button) | |||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| Scans the next sheet without multifeed detection, and from the |
|
|
|
| Confirm that the ADF is closed properly. Otherwise, the |
| second sheet, multifeeds are detected based on the setting | |||
|
| ！ document may not be fed through the ADF. |
| configured in the scanner driver or the Software Operation Panel. | |||||
|
|
|
|
|
|
|
|
| z Auto mode 1 (Bypass by combination of length and position) |
|
|
|
|
|
|
|
| ||
3 Place the documents back in the ADF paper chute. |
| Memorizes the length and location of the paper attachment that | |||||||
| was detected as multifeed, and continues scanning. When a paper | ||||||||
| If a multifeed is detected even though there is no attachment, either |
| attachment of a similar pattern is detected, multifeed detection is | ||||||
| press the [Scan/Stop] button or perform a scan from the computer (do |
| automatically suppressed. (*1)(*2) | ||||||
| not press the [Function] button). If there is a paper attachment which |
| z Auto mode 2 (Bypass by length) | ||||||
| is likely to be the cause of the multifeed error, then proceed to the |
| |||||||
|
| Memorizes the length of the longest paper attachment that was | |||||||
| next step. |
| |||||||
|
| detected as multifeed, and continues scanning. When a paper | |||||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| attachment of the same length or shorter is detected, multifeed |
|
| Check |
|
|
| ||||
|
|
|
|
|
| detection is automatically suppressed. (*1)(*2) | |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
| Function Number Display |
| *1: 32 pages (up to 4 attachments per page) worth of overlap |
|
| Function |
|
|
|
| patterns can be memorized in this mode. When it exceeds this | ||
|
|
|
|
|
| ||||
|
|
|
| [Function] Button |
| limit, the first pattern that was memorized is erased from the | |||
|
|
|
|
|
|
|
| ||
|
| Send to |
|
| memory. | ||||
|
|
|
|
|
| ||||
|
| Scan |
|
|
|
| *2: To erase the memorized overlap patterns and the longest | ||
|
| /Stop |
|
| [Scan/Stop] Button |
| overlap length, press the [Function] button for more than five | ||
|
|
|
|
|
|
|
| ||
|
| Power |
|
|
| seconds while the function number is flashing. The Function | |||
|
|
|
|
|
| ||||
|
|
|
|
|
| Number Display will then display " ". This allows you to erase | |||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| multifeed patterns and the longest overlap length that were not |
|
|
|
|
|
|
|
|
| supposed to be memorized. Be careful with this operation |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| because all memorized patterns will be erased. |
84