Appearance | GE AF-300, C11 guide

1-2 Appearance

(1) Surface cover

(2) Keypad panel

(1)(3) Frequency setting POT (VR) (built-in POT)

(2)

(4) Ratings nameplate

(5) Heat sink

(6) Cooling fan (2 HP or more)

(7) Charge lamp CRG

(8) Control terminal block

(9) Main circuit terminal block 3-phase230V[G,L1/R,L2/S,L3/T,P1,P(+)] Single-phase 230V[G,L1/L,L2/N,P1,P(+)]

(10) Main circuit terminal block [P(+),N(-),U,V,W,G]

(3)

(6)

	(5)
(4)	(9)
(4)
	(9)
	(7)

(7)

(8)

(8)

(10)

(10)

-12-

Image 14

GE AF-300, C11 manual Appearance

Contents

AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU There is a risk of fire Drive may be dropped causing injuryInstructions on use Otherwise fire could occur Otherwise electric shock or fire could occur Instructions on wiringOtherwise, fire could occur Otherwise electric shock could occur There is a risk of accidents Instructions on operationOtherwise accident could occur Otherwise burns could occur General instructions Instruction on maintenance/inspection, and replacementOtherwise electric shock or injury could occur Preface Factory Installed Options Input PhasesHorsepower GE Product Code AF-300 Drive Family Input Voltage 230VAC, 3 phase, 50/60Hz Input 230VAC, Single phase, 50/60Hz Input Before Using This Product Receiving Inspections Appearance Handling the Product Storage and transportation Storage precautionsCarrying 1 Storage and transportation environment AF-300C11 Installation and Connection10 cm 1 Operating environment Otherwise electric shock and fire could occur 1Basic connectionConnection Connecting the main circuit and ground terminals 1 Functions of main circuit and ground terminals Cutting of barrier -3-2 Connection of DC reactor Connecting the control terminalsConnection diagram 4 Surge absorber connection diagram 7 Control terminal block arrangement 2 Functions of control circuit terminals FWD DX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Leakage current Harmonic componentNoise Others Operation Method OperationInspection and Preparation before Operation 1 General operation method 1 Running command Trial Run Keypad Panel Names and Functions Operating Keypad Panel Is pressed at the same time as Procedure Display Press Function Selection List 1 Table of Function Selection List Selecting FunctionFundamental functions 30Ry operation mode Excited when tripped Normally excited Carrier freq 75kHz is set when 0 is specified Sound toneVoltage adjust To 10.0min X3 terminal function Tions Extension Terminal FunctionsControl Functions of Frequency Jump frequency Motor Parameters High Performance Functions Optional Functions Serial communication option Details of Each Function F00 Data protectionF01 Otherwise injuries could occur Key is pressed and decelerates-to-stop when F02 Operation methodMotor runs when GE Start Software Selection During Terminal Operation F03 Maximum output frequency This function sets the maximum output frequency F06 F04 Base frequencyF05 F07 Electronic thermal O/L relayLevel F09 Torque boostF10 F11 Electronic thermal O/L relay Select F12 Electronic thermal O/L relay thermal time constant Operating time? ì? ? ŒcharacteristicsÀ Á Set with F12 F15 Frequency limiter High F14 Restart mode after momentary power failurePhase input Single Phase Input F16 Frequency limiter Low Bias positive F17 Gain For frequency setting signalF18 Bias frequency Bias negative 20mAdc F22 DC injection brakeBraking time F20 DC injection brake Starting frequencyF21 F24 F23 Starting frequencyF25 Stop frequency F26 Motor sound carrier freq F31 FM terminal Function F30 FM terminal voltage adjustF27 Motor sound sound tone F36 30Ry operation mode Normal Tripped Operation X2 terminal function E01 E02 E03X1 terminal function X3 terminal function From previous C01 C02 C03 Jump frequency 1, 2 C07 Multistep frequency settingP00 Motor characteristics C04 Jump frequency Hysteresis H01 Operation time H02 Trip history Data initialization H04 Auto ResetH20 PID control Mode select H03 H23 PID control I-gain H21 PID control Feedback signalH22 PID control P-gain H25 PID control Feedback filter Optional RS485 serial communication unit O00 Option selectionRS485 RTU communication 1 List of Protective Functions Protective FunctionList of protective functions Alarm output Trip Alarm ResetKeypad panel Normal display Alarm display Display Otherwise fire could occur Load excessive? TroubleshootingCase of tripping Consider using DC Power supply voltage within specified value?Does OU activate when load is removed OvervoltageOU Heat sink overheat- ing OH1 Is electronic thermal O/L relay setting correct? Drive overload OLU or motor overload OL Probable faulty drive. Contact GE Fuji Set o00 to Noise source nearby? Input phase failure Lin and imbalance Connect the input wires correctly Motor does not start When motor rotates but the speed does not change Setting too low? To 0? When motor stalls during accelerationMotor generates ab Function change is disabled Normal heat Set F00 to Periodic Inspection Maintenance and InspectionDaily Inspection There is danger of electric shock Electrolyte leakage Visual Not abnormal 1 Periodic inspection listDiscoloration and distortion Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection Electrical measurements in the Main Circuit Three-phaseSingle -phase 1 Meter for measuring the main circuit + + Case of 3-phase input seriesInput series Motor Supply Inquiries about Products and Product Warranty 6Warranty Service Warranty Coverage IN-WARRANTY Failure Checklist Specifications Standard Specifications Drive output capacity kVA at Common specifications RUN StopPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 External Options 1 External Options OptionsBuilt-in Options Applicable DC reactors Connection method General PrecautionsCompliance with standards L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CM General RFI Filters Electromagnetic Compatibility EMCGeneral 1 RFI filters Dimensions Ferrite Ring DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite