GE C11, AF-300 manual

	Item		Specifications	Remarks
	Installation	∙ Indoor use only. Do not install a dusty location(Degree of pollution: 2) or
	location	expose to direct sunlight, corrosive gases, flammable gases.
	Ambient	∙ -10 to +50°C (+14 to +122°F )
	temperature
	Ambient	∙ 5 to 95%RH ( No condensation )
Environment	humidity
	Altitude	∙ 3300 Feet (1000 m) or less

	Vibration	∙ 3 mm:	2 to less than 9 Hz
		∙ 9.8m/s2:	9 to less than 20 Hz
		∙ 2m/s2:	20 to less than 55 Hz
		∙ 2m/s2:	20 to less than 55 Hz
		∙ 1m/s2:	55 to less than 200 Hz
	Storage tem-	∙ -25 to +65°C
	perature
	Storage humid-	∙ 5 to 95% RH (No condensation)
	ity
	Higher	∙ Terminal for connecting power-factor correcting DC reactor (DCR) is pro-		P1, P(+) terminal
	harmonics	vided as standard.
	current
Others	suppression
	Charging sup-	∙ Charging suppression resistor is built-in for all drive unit.
	pression resis-
	tor
	Cooling fan	∙ Cooling fan can be automatically stopped when drive is stopped.
	ON/OFF con-
	trol

- 83-

Image 85

GE C11, AF-300 manual

Contents

AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU Instructions on use Drive may be dropped causing injuryThere is a risk of fire Otherwise fire could occur Otherwise, fire could occur Instructions on wiringOtherwise electric shock or fire could occur Otherwise electric shock could occur Otherwise accident could occur Instructions on operationThere is a risk of accidents Otherwise burns could occur Otherwise electric shock or injury could occur Instruction on maintenance/inspection, and replacementGeneral instructions Preface Horsepower Input PhasesFactory Installed Options GE Product Code AF-300 Drive Family Input Voltage 230VAC, Single phase, 50/60Hz Input 230VAC, 3 phase, 50/60Hz Input Receiving Inspections Before Using This Product Appearance Handling the Product Carrying Storage precautionsStorage and transportation 1 Storage and transportation environment 10 cm Installation and ConnectionAF-300C11 1 Operating environment Connection 1Basic connectionOtherwise electric shock and fire could occur 1 Functions of main circuit and ground terminals Connecting the main circuit and ground terminals Connection diagram Connecting the control terminalsCutting of barrier -3-2 Connection of DC reactor 4 Surge absorber connection diagram 7 Control terminal block arrangement FWD 2 Functions of control circuit terminals DX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Noise Harmonic componentLeakage current Others Inspection and Preparation before Operation OperationOperation Method 1 General operation method Trial Run 1 Running command Names and Functions Keypad Panel Is pressed at the same time as Operating Keypad Panel Procedure Display Press Fundamental functions Selecting FunctionFunction Selection List 1 Table of Function Selection List Voltage adjust Carrier freq 75kHz is set when 0 is specified Sound tone30Ry operation mode Excited when tripped Normally excited To 10.0min Control Functions of Frequency Extension Terminal FunctionsX3 terminal function Tions Jump frequency High Performance Functions Motor Parameters Serial communication option Optional Functions F01 F00 Data protectionDetails of Each Function Otherwise injuries could occur Motor runs when F02 Operation methodKey is pressed and decelerates-to-stop when GE Start Software Selection During Terminal Operation This function sets the maximum output frequency F03 Maximum output frequency F05 F04 Base frequencyF06 F07 F10 F11 Electronic thermal O/L relay Select F09 Torque boostElectronic thermal O/L relayLevel F12 Electronic thermal O/L relay thermal time constant Set with F12 Operating time? ì? ? ŒcharacteristicsÀ Á Phase input Single Phase Input F14 Restart mode after momentary power failureF15 Frequency limiter High F16 Frequency limiter Low F18 Bias frequency F17 Gain For frequency setting signalBias positive Bias negative 20mAdc F21 F20 DC injection brake Starting frequencyF22 DC injection brakeBraking time F25 Stop frequency F23 Starting frequencyF24 F26 Motor sound carrier freq F27 Motor sound sound tone F30 FM terminal voltage adjustF31 FM terminal Function Normal Tripped Operation F36 30Ry operation mode X1 terminal function E01 E02 E03X2 terminal function X3 terminal function From previous P00 Motor characteristics C07 Multistep frequency settingC01 C02 C03 Jump frequency 1, 2 C04 Jump frequency Hysteresis H02 Trip history H01 Operation time H20 PID control Mode select H04 Auto ResetData initialization H03 H22 PID control P-gain H21 PID control Feedback signalH23 PID control I-gain H25 PID control Feedback filter RS485 RTU communication O00 Option selectionOptional RS485 serial communication unit List of protective functions Protective Function1 List of Protective Functions Keypad panel Normal display Alarm display Display Alarm ResetAlarm output Trip Otherwise fire could occur Case of tripping TroubleshootingLoad excessive? Does OU activate when load is removed Power supply voltage within specified value?Consider using DC OvervoltageOU Heat sink overheat- ing OH1 Drive overload OLU or motor overload OL Is electronic thermal O/L relay setting correct? Noise source nearby? Probable faulty drive. Contact GE Fuji Set o00 to Connect the input wires correctly Input phase failure Lin and imbalance Motor does not start Setting too low? When motor rotates but the speed does not change Motor generates ab Function change is disabled Normal heat When motor stalls during accelerationTo 0? Set F00 to Daily Inspection Maintenance and InspectionPeriodic Inspection There is danger of electric shock Discoloration and distortion Visual Not abnormal 1 Periodic inspection listElectrolyte leakage Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection Single -phase Three-phaseElectrical measurements in the Main Circuit 1 Meter for measuring the main circuit Input series Case of 3-phase input series+ + Motor Supply Inquiries about Products and Product Warranty Warranty Coverage 6Warranty Service IN-WARRANTY Failure Checklist Standard Specifications Specifications Drive output capacity kVA at RUN Stop Common specificationsPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 Built-in Options OptionsExternal Options 1 External Options Connection method Applicable DC reactors Compliance with standards PrecautionsGeneral L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CM General General Electromagnetic Compatibility EMCRFI Filters Ferrite Ring Dimensions 1 RFI filters DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite