Handling the Product | GE C11, AF-300 manual

1-3 Handling the Product

Remove the surface cover as explained below.

(1) For 1/8 to 1 HP

Grasp the upper and lower parts of the cover with both hands and pull it to the front of the drive.

(2) For 2 to 5 HP

Expand the lower part of the cover horizontally, lift the cover to the front, and then remove it.

-13-

Image 15

GE C11, AF-300 manual Handling the Product

Contents

AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU Otherwise fire could occur Drive may be dropped causing injuryInstructions on use There is a risk of fire Otherwise electric shock could occur Instructions on wiringOtherwise, fire could occur Otherwise electric shock or fire could occur Otherwise burns could occur Instructions on operationOtherwise accident could occur There is a risk of accidents Instruction on maintenance/inspection, and replacement Otherwise electric shock or injury could occurGeneral instructions Preface GE Product Code AF-300 Drive Family Input Voltage Input PhasesHorsepower Factory Installed Options 230VAC, Single phase, 50/60Hz Input 230VAC, 3 phase, 50/60Hz Input Receiving Inspections Before Using This Product Appearance Handling the Product 1 Storage and transportation environment Storage precautionsCarrying Storage and transportation 1 Operating environment Installation and Connection10 cm AF-300C11 1Basic connection ConnectionOtherwise electric shock and fire could occur 1 Functions of main circuit and ground terminals Connecting the main circuit and ground terminals Connecting the control terminals Connection diagramCutting of barrier -3-2 Connection of DC reactor 4 Surge absorber connection diagram 7 Control terminal block arrangement FWD 2 Functions of control circuit terminals DX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Others Harmonic componentNoise Leakage current 1 General operation method OperationInspection and Preparation before Operation Operation Method Trial Run 1 Running command Names and Functions Keypad Panel Is pressed at the same time as Operating Keypad Panel Procedure Display Press Selecting Function Fundamental functionsFunction Selection List 1 Table of Function Selection List To 10.0min Carrier freq 75kHz is set when 0 is specified Sound toneVoltage adjust 30Ry operation mode Excited when tripped Normally excited Jump frequency Extension Terminal FunctionsControl Functions of Frequency X3 terminal function Tions High Performance Functions Motor Parameters Serial communication option Optional Functions Otherwise injuries could occur F00 Data protectionF01 Details of Each Function F02 Operation method Motor runs whenKey is pressed and decelerates-to-stop when GE Start Software Selection During Terminal Operation This function sets the maximum output frequency F03 Maximum output frequency F07 F04 Base frequencyF05 F06 F09 Torque boost F10 F11 Electronic thermal O/L relay SelectElectronic thermal O/L relayLevel F12 Electronic thermal O/L relay thermal time constant Set with F12 Operating time? ì? ? ŒcharacteristicsÀ Á F16 Frequency limiter Low F14 Restart mode after momentary power failurePhase input Single Phase Input F15 Frequency limiter High Bias negative 20mAdc F17 Gain For frequency setting signalF18 Bias frequency Bias positive F20 DC injection brake Starting frequency F21F22 DC injection brakeBraking time F26 Motor sound carrier freq F23 Starting frequencyF25 Stop frequency F24 F30 FM terminal voltage adjust F27 Motor sound sound toneF31 FM terminal Function Normal Tripped Operation F36 30Ry operation mode X3 terminal function E01 E02 E03X1 terminal function X2 terminal function From previous C04 Jump frequency Hysteresis C07 Multistep frequency settingP00 Motor characteristics C01 C02 C03 Jump frequency 1, 2 H02 Trip history H01 Operation time H03 H04 Auto ResetH20 PID control Mode select Data initialization H25 PID control Feedback filter H21 PID control Feedback signalH22 PID control P-gain H23 PID control I-gain O00 Option selection RS485 RTU communicationOptional RS485 serial communication unit Protective Function List of protective functions1 List of Protective Functions Otherwise fire could occur Alarm ResetKeypad panel Normal display Alarm display Display Alarm output Trip Troubleshooting Case of trippingLoad excessive? OvervoltageOU Power supply voltage within specified value?Does OU activate when load is removed Consider using DC Heat sink overheat- ing OH1 Drive overload OLU or motor overload OL Is electronic thermal O/L relay setting correct? Noise source nearby? Probable faulty drive. Contact GE Fuji Set o00 to Connect the input wires correctly Input phase failure Lin and imbalance Motor does not start Setting too low? When motor rotates but the speed does not change Set F00 to When motor stalls during accelerationMotor generates ab Function change is disabled Normal heat To 0? There is danger of electric shock Maintenance and InspectionDaily Inspection Periodic Inspection 1 Periodic inspection list Discoloration and distortion Visual Not abnormalElectrolyte leakage Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection 1 Meter for measuring the main circuit Three-phaseSingle -phase Electrical measurements in the Main Circuit Motor Supply Case of 3-phase input seriesInput series + + Inquiries about Products and Product Warranty Warranty Coverage 6Warranty Service IN-WARRANTY Failure Checklist Standard Specifications Specifications Drive output capacity kVA at RUN Stop Common specificationsPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 Options Built-in OptionsExternal Options 1 External Options Connection method Applicable DC reactors L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CM PrecautionsCompliance with standards General General Electromagnetic Compatibility EMC GeneralRFI Filters Ferrite Ring Dimensions 1 RFI filters DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite