Input phase failure Lin and imbalance | GE AF-300, C11 specs

(9) Input phase failure (Lin) and imbalance

Lin

Are all the three phases of the

input voltage supplied?

Yes

Is the inter-phase imbalance ratio

within 2%?

Yes

Probable faulty drive. Contact

GE Fuji.

No

No

Connect the input wires correctly.

Examine the power supply system to satisfy the specification value.

-66-

Image 68

GE AF-300, C11 manual Input phase failure Lin and imbalance, Connect the input wires correctly

Contents

AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU Drive may be dropped causing injury Instructions on useThere is a risk of fire Otherwise fire could occur Instructions on wiring Otherwise, fire could occurOtherwise electric shock or fire could occur Otherwise electric shock could occur Instructions on operation Otherwise accident could occurThere is a risk of accidents Otherwise burns could occur General instructions Instruction on maintenance/inspection, and replacementOtherwise electric shock or injury could occur Preface Input Phases HorsepowerFactory Installed Options GE Product Code AF-300 Drive Family Input Voltage 230VAC, 3 phase, 50/60Hz Input 230VAC, Single phase, 50/60Hz Input Before Using This Product Receiving Inspections Appearance Handling the Product Storage precautions CarryingStorage and transportation 1 Storage and transportation environment Installation and Connection 10 cmAF-300C11 1 Operating environment Otherwise electric shock and fire could occur 1Basic connectionConnection Connecting the main circuit and ground terminals 1 Functions of main circuit and ground terminals Cutting of barrier -3-2 Connection of DC reactor Connecting the control terminalsConnection diagram 4 Surge absorber connection diagram 7 Control terminal block arrangement 2 Functions of control circuit terminals FWD DX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Harmonic component NoiseLeakage current Others Operation Inspection and Preparation before OperationOperation Method 1 General operation method 1 Running command Trial Run Keypad Panel Names and Functions Operating Keypad Panel Is pressed at the same time as Procedure Display Press Function Selection List 1 Table of Function Selection List Selecting FunctionFundamental functions Carrier freq 75kHz is set when 0 is specified Sound tone Voltage adjust30Ry operation mode Excited when tripped Normally excited To 10.0min Extension Terminal Functions Control Functions of FrequencyX3 terminal function Tions Jump frequency Motor Parameters High Performance Functions Optional Functions Serial communication option F00 Data protection F01Details of Each Function Otherwise injuries could occur Key is pressed and decelerates-to-stop when F02 Operation methodMotor runs when GE Start Software Selection During Terminal Operation F03 Maximum output frequency This function sets the maximum output frequency F04 Base frequency F05F06 F07 Electronic thermal O/L relayLevel F09 Torque boostF10 F11 Electronic thermal O/L relay Select F12 Electronic thermal O/L relay thermal time constant Operating time? ì? ? ŒcharacteristicsÀ Á Set with F12 F14 Restart mode after momentary power failure Phase input Single Phase InputF15 Frequency limiter High F16 Frequency limiter Low F17 Gain For frequency setting signal F18 Bias frequencyBias positive Bias negative 20mAdc F22 DC injection brakeBraking time F20 DC injection brake Starting frequencyF21 F23 Starting frequency F25 Stop frequencyF24 F26 Motor sound carrier freq F31 FM terminal Function F30 FM terminal voltage adjustF27 Motor sound sound tone F36 30Ry operation mode Normal Tripped Operation E01 E02 E03 X1 terminal functionX2 terminal function X3 terminal function From previous C07 Multistep frequency setting P00 Motor characteristicsC01 C02 C03 Jump frequency 1, 2 C04 Jump frequency Hysteresis H01 Operation time H02 Trip history H04 Auto Reset H20 PID control Mode selectData initialization H03 H21 PID control Feedback signal H22 PID control P-gainH23 PID control I-gain H25 PID control Feedback filter Optional RS485 serial communication unit O00 Option selectionRS485 RTU communication 1 List of Protective Functions Protective FunctionList of protective functions Alarm Reset Keypad panel Normal display Alarm display DisplayAlarm output Trip Otherwise fire could occur Load excessive? TroubleshootingCase of tripping Power supply voltage within specified value? Does OU activate when load is removedConsider using DC OvervoltageOU Heat sink overheat- ing OH1 Is electronic thermal O/L relay setting correct? Drive overload OLU or motor overload OL Probable faulty drive. Contact GE Fuji Set o00 to Noise source nearby? Input phase failure Lin and imbalance Connect the input wires correctly Motor does not start When motor rotates but the speed does not change Setting too low? When motor stalls during acceleration Motor generates ab Function change is disabled Normal heatTo 0? Set F00 to Maintenance and Inspection Daily InspectionPeriodic Inspection There is danger of electric shock Electrolyte leakage Visual Not abnormal 1 Periodic inspection listDiscoloration and distortion Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection Three-phase Single -phaseElectrical measurements in the Main Circuit 1 Meter for measuring the main circuit Case of 3-phase input series Input series+ + Motor Supply Inquiries about Products and Product Warranty 6Warranty Service Warranty Coverage IN-WARRANTY Failure Checklist Specifications Standard Specifications Drive output capacity kVA at Common specifications RUN StopPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 External Options 1 External Options OptionsBuilt-in Options Applicable DC reactors Connection method Precautions Compliance with standardsGeneral L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CM General RFI Filters Electromagnetic Compatibility EMCGeneral 1 RFI filters Dimensions Ferrite Ring DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite