Manuals / GE / Household Appliance / Sewing Machine

GE AF-300 C03 Jump frequency 1, 2, C04 Jump frequency Hysteresis, C07 Multistep frequency setting

Models: C11 AF-300

1 98

Download 98 pages 7.53 Kb

Page 56

C03 Jump frequency 1, 2, 3

Change during operation: N = impossible, Y* = possible (enabled by using	FUNC
	DATA

C01

C02

C03 Jump frequency 1, 2, 3

), Y= possible (enabled by using			)

		Factory	Change during
		setting	operation
	C01	0.0Hz	Y
	C02	0.0Hz	Y
	C03	0.0Hz	Y

These functions jump frequencies to prevent overlap be- tween the load mechanical resonance point and drive output frequency.

Up to three jump points can be set.

These function do not operate when 0Hz is set.

No frequency is jumped during acceleration and decel- eration.

If three continuous frequencies are set, the total of the three jump widths is set as the jump width.

	Output Frequency
	Jump
	frequency	Jump width
	Jump	Jump width
	Jump
	frequency	Jump width
		Jump width
	Jump
	frequency	Jump width
		Frequency setting

C04 Jump frequency (Hysteresis)

Factory	Change during
setting	operation
3Hz	Y

This function sets a jump width in a range from 0 to 30Hz in 1Hz step.

C05 Multistep frequency setting 1

C06 Multistep frequency setting 2

	Factory	Change during
	setting	operation
		operation
C05	0.0Hz	Y
C06	0.0Hz	Y
C07	0.0Hz	Y

C07 Multistep frequency setting 3

These functions set a multistep frequency setting from 0 to 120Hz in 0.1Hz step (for 99.9 Hz or less) or 1Hz step (for 100Hz or more) by switching the external contact signal.

The ON and OFF of terminal function SS1/SS2 (see explanation of E01, E02, and E03) switches between the frequencies set by these functions C05, C06, and C07.

P00 Motor characteristics

Factory	Change during
setting	operation
	operation
2	Y

This function removes abnormalities in the output current such as current vibration. 0 Current vibration is not suppressed.

to

1 0 Current vibration is minimized.

-54-

Image 56

GE AF-300, C11 manual C03 Jump frequency 1, 2, C04 Jump frequency Hysteresis, C07 Multistep frequency setting

Contents

AF-300 C11 TM User’s Guide1 BEFORE USING THIS PRODUCT 2 INSTALLATION AND CONNECTION15TROUBLESHOOTING 8 MAINTENANCE AND INSPECTIONSafety Instructions 4. Use MCCB or MC that conforms to EN or IEC standard Compliance with low voltage directive in EU Continued Instructions on transport/installation Drive may be dropped causing injuryInstructions on use There is a risk of fireInstructions on wiring Otherwise, fire could occurotherwise electric shock or fire could occur otherwise electric shock could occurInstructions on operation Otherwise electric shock could occurOtherwise accident could occur There is a risk of accidentsInstruction on maintenance/inspection, and replacement Otherwise electric shock or injury could occurotherwise electric shock or injury could occur Instruction on disposalPreface AF-300C11 Model Numbering System Diagram Input PhasesHorsepower Factory Installed OptionsAF-300C11 230VAC, 3 phase, 50/60Hz Input230VAC, Single phase, 50/60Hz Input Figure1-1-1 Ratings nameplate 1 Before Using This Product1-1 Receiving Inspections 1-2 Appearance 13 Frequency setting POT VR built-in POT1 Surface cover 2 Keypad panel 4 Ratings nameplate 5 Heat sink 6 Cooling fan 2 HP or more2 For 2 to 5 HP 1-3 Handling the ProductRemove the surface cover as explained below 1 For 1/8 to 1 HP Storage precautions 1-4 Carrying1-5 Storage and transportation Table 1-5-1 Storage and transportation environment2 Installation and Connection 2-2 Installation Method10 cm 0.4”Figure 2-2-2 How to install two or more drives 2-3-1 Basic connection2-3 Connection otherwise electric shock and fire could occurFigure 2-3-1 Arrangement of main circuit and ground termi nals 2-3-2 Connecting the main circuit and ground terminalsTable 2-3-1 Functions of main circuit and ground terminals 2-3-3 Connecting the control terminals a Connection diagramb Cutting of barrier Figure 2-3-2 Connection of DC reactor Figure 2-3-3 Digital input terminalNote the following when wiring Figure 2-3-4 Surge absorber connection diagramFigure 2.3.6 Connection of sheath of shielded wire Figure 2-3-5 End treatmentFigure 2-3-8 How to pull out the control wiring Figure 2-3-7 Control terminal block arrangementTable 2-3-2 Functions of control circuit terminals Page Figure 2-3-9 Wiring diagram of keypad panel operation 2-3-4 Connection examplesTo ground terminal Figure 2-3-10 Wiring diagram of external operation 200 to 200 toL1/R L2/SFUSE L1/R L2/S L3/T2-4-1 Harmonic component 2-4-2 Noise2-4-3 Leakage current 2-4 Others3 Operation 3-1 Inspection and Preparation before Operation2. otherwise electric shock could occur 3-2 Operation MethodTable 3-3-1 Running command 3-3 Trial Run4 Keypad Panel otherwise burns could occur4-1 Names and Functions otherwise accidents could occur1. 2 A 4-2 Operating Keypad Panel6 0 DATA 5 Selecting Function F Fundamental functions5-1 Function Selection List Table 5-1-1 Table of Function Selection ListFactory E Extension Terminal Functions C Control Functions of FrequencyP Motor Parameters H High Performance FunctionsO Optional Functions serial communication optionotherwise injuries could occur F00 Data protection5-2 Details of Each Function F02 Operation method POWER ON NETWORKMODE STOP KEY FWDFUNC DATA F03 Maximum output frequencyotherwise injuries could occur F04 Base frequency toMaximum voltage f Base frequencyPage 0.5 to 10.0 min. can be set in 0.1 min. step Electronic thermal O/L relay thermal time constantcurrent that is 150% of the operation level flows Operating“ time? ì? ? ŒcharacteristicsÀ “ Á Continued from previous pageF16 Frequency limiter Low F14 Restart mode after momentary power failureF15 Frequency limiter High F17 Gain for frequency setting signal F18 Bias frequency1 2 to 1 2 100%F20 DC injection brake starting frequency F22 DC injection brakeBraking timeotherwise injuries could occur DC injection brake Braking levelStarting frequency Stop frequencyF26 Motor sound carrier freq 0.2HzF31 FM terminal Function FM terminal voltage adjustF27 Motor sound sound tone F36 30Ry operation mode Excitedwhen trippedE01 E02 E03 X1 terminal functionX2 terminal function X3 terminal functionLink operation selection LE C05 Multistep frequency setting C06 Multistep frequency setting C07 Multistep frequency settingP00 Motor characteristics C03 Jump frequency 1, 2H01 Operation time H02 Trip historyFUNC DATAH04 Auto Reset Data initializationH06 Fan stop operation H20 PID control Mode selectH21 PID control Feedback signal H22 PID control P-gainH23 PID control I-gain H25 PID control Feedback filteroptional RS485 serial communication unit o00 Option selectionRS485 RTU communication Table 6-1-1 List of Protective Functions 6 Protective Function6-1 List of protective functions 6-2 Alarm Reset Figure. 6-2-1 How to input the reset commandotherwise fire could occur Reset command7 Troubleshooting 7-1 In case of tripping2 OvervoltageOU Heat sink overheat- ing OH1 Replace cooling fanDo characteristics of elec tronic thermal O/L relayand those of motor over load match?7 Memory error Er1 Abnormal dis- play or indica- tion goes out 9 Input phase failure Lin and imbalance Lin Are all the three phases of the input voltage supplied?Is the inter-phase imbalance ratio within 2%? Probable faulty drive. Contact GE Fuji1 When motor does not rotate Note Verify the function settings for the operation commands and frequency setting values on the keypad 7-2 Other trouble2 When motor rotates but the speed does not change 3 When motor stalls during acceleration 4 When motor generates abnormal heat5 When function change disabled Function change is disabled8 Maintenance and Inspection 8-1 Daily Inspection8-2 Periodic Inspection There is danger of electric shockConductor Table 8-2-1 Periodic inspection listand wire Cooling Controlsystem Three-phase Single -phase8-3 Electrical measurements in the Main Circuit Table 8-3-1 Meter for measuring the main circuitIn the case of 3-phase input series Figure 8-3-1 Diagram for connections of meters 8-4 Insulation Testinput series Motor8-5 Inquiries about Products and Product Warranty 8-6 Warranty Service IN-WARRANTY FAILURE CHECKLIST L1 Volts L2 Volts L3 Volts9 Specifications 9-1 Standard SpecificationsDrive output capacity kVA at ratingsCommon specifications CharacteristicSpecifications power failureThe CRG lamp is on when the capacitor is charged ∙ OH2 Overheating External alarmSpecifications Ground faultInput phase fail due to inter-phase imbalanceSpecifications Installationtemperature ∙ Cooling fan can be automatically stopped when drive is stopped9-3 Dimensions 3 - phase 230V seriesSingle phase 230V series 3- phaseTERMII NAL T E R M II N A L3 - phase 230V series Single phase 230V series10 Options 10-1 Built-in Options10-2 External Options Table 10-2-1 External Options11 Applicable DC reactors Connection method12-2-2 Precautions Fig. 12-1-1 Recommended wiring12 Compliance with standards 12-1-1 General12-3-1 General 12-3-2 Precautions12-2-1 General 13-2 RFI Filters 13 Electromagnetic Compatibility EMC13-1 General Fig.13-2-1 Table 13-2-1 RFI filters DimensionsD T Ferrite Ring Dimensions Remark To minimize the conducted radio disturbance in the power distribution system, the length of motor cable Fig. 13-3-1 Recommended Installation fix a part of shield by a clamp Fig. 13-3-2 Recommended installation detail inside the enclosureMetal Cabinet GE Fuji Drives USA, Inc. 1501 Roanoke Blvd. Suite GEH-6640 991213 FERGADV INR-Si47-0562-E