Noise source nearby? | GE C11, AF-300 specification

(7) Memory error (Er1)

Abnormal dis- play or indica- tion goes out

CPU error (Er3)

Memory error Er 1

CPU error Er 3

Analog frequency set to negative value?

No	Yes

Turn power OFF then ON again after CHARGE lamp has gone out.

Reset analog frequency to positive value.

Is data displayed on LED?

Yes

No

Noise source nearby?

No

Yes

Remedy faulty parts.

Drive is normal. Continue operation.

Probable faulty drive. Contact GE Fuji.

(8) RS485 Communication Error (Er8) [In case RS485 communication is not used]

Communication

Error Er8

o00 is set to 1?

Yes

No

Probable faulty drive. Contact GE Fuji.

Set o00 to 0.

*For Er8 measures when using RS485, refer to the instruction manual for optional RS485 communication card.

-65-

Image 67

GE C11, AF-300 manual Noise source nearby?, Probable faulty drive. Contact GE Fuji Set o00 to

Contents

AF-300 C11 TM Table of Contents Safety Instructions Page Compliance with low voltage directive in EU Otherwise fire could occur Drive may be dropped causing injuryInstructions on use There is a risk of fire Otherwise electric shock could occur Instructions on wiringOtherwise, fire could occur Otherwise electric shock or fire could occur Otherwise burns could occur Instructions on operationOtherwise accident could occur There is a risk of accidents Otherwise electric shock or injury could occur Instruction on maintenance/inspection, and replacementGeneral instructions Preface GE Product Code AF-300 Drive Family Input Voltage Input PhasesHorsepower Factory Installed Options 230VAC, Single phase, 50/60Hz Input 230VAC, 3 phase, 50/60Hz Input Receiving Inspections Before Using This Product Appearance Handling the Product 1 Storage and transportation environment Storage precautionsCarrying Storage and transportation 1 Operating environment Installation and Connection10 cm AF-300C11 Connection 1Basic connectionOtherwise electric shock and fire could occur 1 Functions of main circuit and ground terminals Connecting the main circuit and ground terminals Connection diagram Connecting the control terminalsCutting of barrier -3-2 Connection of DC reactor 4 Surge absorber connection diagram 7 Control terminal block arrangement FWD 2 Functions of control circuit terminals DX+ Connection examples 200 to 50/60Hz Mccb Fuse Connection to PLC when analog signal is input from PLC Others Harmonic componentNoise Leakage current 1 General operation method OperationInspection and Preparation before Operation Operation Method Trial Run 1 Running command Names and Functions Keypad Panel Is pressed at the same time as Operating Keypad Panel Procedure Display Press Fundamental functions Selecting FunctionFunction Selection List 1 Table of Function Selection List To 10.0min Carrier freq 75kHz is set when 0 is specified Sound toneVoltage adjust 30Ry operation mode Excited when tripped Normally excited Jump frequency Extension Terminal FunctionsControl Functions of Frequency X3 terminal function Tions High Performance Functions Motor Parameters Serial communication option Optional Functions Otherwise injuries could occur F00 Data protectionF01 Details of Each Function Motor runs when F02 Operation methodKey is pressed and decelerates-to-stop when GE Start Software Selection During Terminal Operation This function sets the maximum output frequency F03 Maximum output frequency F07 F04 Base frequencyF05 F06 F10 F11 Electronic thermal O/L relay Select F09 Torque boostElectronic thermal O/L relayLevel F12 Electronic thermal O/L relay thermal time constant Set with F12 Operating time? ì? ? ŒcharacteristicsÀ Á F16 Frequency limiter Low F14 Restart mode after momentary power failurePhase input Single Phase Input F15 Frequency limiter High Bias negative 20mAdc F17 Gain For frequency setting signalF18 Bias frequency Bias positive F21 F20 DC injection brake Starting frequencyF22 DC injection brakeBraking time F26 Motor sound carrier freq F23 Starting frequencyF25 Stop frequency F24 F27 Motor sound sound tone F30 FM terminal voltage adjustF31 FM terminal Function Normal Tripped Operation F36 30Ry operation mode X3 terminal function E01 E02 E03X1 terminal function X2 terminal function From previous C04 Jump frequency Hysteresis C07 Multistep frequency settingP00 Motor characteristics C01 C02 C03 Jump frequency 1, 2 H02 Trip history H01 Operation time H03 H04 Auto ResetH20 PID control Mode select Data initialization H25 PID control Feedback filter H21 PID control Feedback signalH22 PID control P-gain H23 PID control I-gain RS485 RTU communication O00 Option selectionOptional RS485 serial communication unit List of protective functions Protective Function1 List of Protective Functions Otherwise fire could occur Alarm ResetKeypad panel Normal display Alarm display Display Alarm output Trip Case of tripping TroubleshootingLoad excessive? OvervoltageOU Power supply voltage within specified value?Does OU activate when load is removed Consider using DC Heat sink overheat- ing OH1 Drive overload OLU or motor overload OL Is electronic thermal O/L relay setting correct? Noise source nearby? Probable faulty drive. Contact GE Fuji Set o00 to Connect the input wires correctly Input phase failure Lin and imbalance Motor does not start Setting too low? When motor rotates but the speed does not change Set F00 to When motor stalls during accelerationMotor generates ab Function change is disabled Normal heat To 0? There is danger of electric shock Maintenance and InspectionDaily Inspection Periodic Inspection Discoloration and distortion Visual Not abnormal 1 Periodic inspection listElectrolyte leakage Visual Not abnormal More Overheating? Is off 2Tighten more 3Visual inspection 1 Meter for measuring the main circuit Three-phaseSingle -phase Electrical measurements in the Main Circuit Motor Supply Case of 3-phase input seriesInput series + + Inquiries about Products and Product Warranty Warranty Coverage 6Warranty Service IN-WARRANTY Failure Checklist Standard Specifications Specifications Drive output capacity kVA at RUN Stop Common specificationsPage Page Page Dimensions 00.2 2 68 17.2 D 00.2 Terminal Terminal 1 M2.5 00.2 2 Built-in Options OptionsExternal Options 1 External Options Connection method Applicable DC reactors L1/L L2/N L1/R L2/S L3/T P1 + N- U THR CM PrecautionsCompliance with standards General General General Electromagnetic Compatibility EMCRFI Filters Ferrite Ring Dimensions 1 RFI filters DimensionsPage 1 Recommended Installation 2 Recommended installation detail inside the enclosure GE Fuji Drives USA, Inc Roanoke Blvd. Suite