Hitachi hitachi series inverter - page 50

48

“d” Function

Func.

Code Name Description

Run

Mode

Edit

Units

d029 Positioning command monitor Displays the positioning command,

range is –268435455~+268435455

− −

d030 Current position monitor Displays the current position, range

is –268435455~+268435455

− −

d050 Dual monitor Displays two different data

configured in b160 and b161.

− −

d060 Inverter mode monitor Displays currently selected inverter

mode :

I-C:IM CT mode/I-v:IM VT mode/

P:PM

− −

D080 Trip counter Number of trip events,

Range is 0. to 65530

− events

D081 Trip monitor 1 − −

D082 Trip monitor 2 − −

D083 Trip monitor 3 − −

d084 Trip monitor 4 − −

d085 Trip monitor 5 − −

d086 Trip monitor 6

Displays trip event information:

• Error code

• Output frequency at trip point

• Motor current at trip point

• DC bus voltage at trip point

• Cumulative inverter operation

time at trip point

• Cumulative power-ON time at

trip point

− −

d090 Warning monitor Displays the warning code − −

D102 DC bus voltage monitor Voltage of inverter internal DC bus,

Range is 0.0 to 999.9

− V

d103 BRD load ratio monitor Usage ratio of integrated brake

chopper, range is 0.0~100.0%

− %

D104 Electronic thermal monitor Accumulated value of electronic

thermal detection, range is from

0.0~100.0%

− %

Contents

Main WJ200 Series Inverter Quick Reference Guide Hitachi Industrial Equipment Systems Co., Ltd. Manual Number: NT3251AX March 2012 Page Page Terminal symbols and Screw size Fuse Sizes 4 Inverter Specification Label Ver:2. 0 200-240 200-240 -001SF 2.0/1.3 -001 / WJ200 Inverter Specifications Model-specific tables for 200V and 400V class inverters WJ200 Inverter Specifications, continued WJ200 Inverter Specifications, continued Page Basic System Description M Determining Wire and Fuse Sizes Wire the Inverter Input to a Supply Page Page Using the Front Panel Keypad Key and Indicator Legend Keys, Modes, and Parameters Keypad Navigation Map Page A001 A002 02 F001 01 d001 0.00 Page Connecting to PLCs and Other Devices Example Wiring Diagram Forward Control Logic Signal Specifications Page Sink/source logic of intelligent input terminals Wire size for control and relay terminals 24 Recommended ferrule How to connect? 8 L Intelligent Terminal Listing Intelligent Inputs Use the following table to locate pages for intelligent input material in this chapter. Intelligent Outputs Use the following table to locate pages for intelligent output material in this chapter. 27 Using Intelligent Input Terminals Jumper wire Jum Page * 30 Inserting diode 1 Forward Run/Stop and Reverse Run/Stop Commands: Multi-Speed Select ~Binary Operation Two Stage Acceleration and Deceleration Unattended Start Protection Reset Inverter Using Intelligent Output Terminals RUN Run Signal Frequency Arrival Signals FA1 Page Alarm Signal L A Page Analog Input Operation Page Pulse Train Input Operation Analog Output Operation Page Monitoring functions IMPORTANT D001 D002 D003 D006 D007 d008 d009 d010 Page Main Profile Parameters F001 F002 Acceleration time (1) 10.0 sec. F202 F003 Deceleration time (1) 10.0 sec. F203 Standard Functions U A001 Frequency source U 02 A201 U U A035 A016 U A017 00 - a019 U A020 A220 A021 A038 U A041 Torque boost select U 00 A241 U A042 52 A242 A043 U 0.0 sec. a059 U U 5.0 sec. A061 U 0.0 sec. A071 54 A072 1.0 A086 Energy-saving mode tuning Range is 0.0 to 100 %. U 50.0 % A073 1.0 sec A074 10.00 sec A093 Deceleration time (2) 10.00 sec A293 U 10.00 sec A094 U 00 A294 00 01 02 U 02 A142 U 0.0 sec. U 03 A143 U 0.00 Hz a157 U U 0.0 sec A161 Fine Tuning Functions B001 04 U B002 U B013 U 01 U 0.00 U 01 U Rated b026 U 2 U 0. U 1.0 sec. U Rated B029 U 0.5 sec. B030 U 00 U 04 b038 U 0.0 Hz U 001 B039 U 100. % B061 U 1.00 0. % B062 B087 B088 b089 b090 B091 U 360/ b097 BRD resistor value Min.Resistance to 600.0 U Min. U 00 - b121 Brake Wait Time for Release Set range: 0.00 to 5.00 sec U 0.00 Sec b122 b123 b124 U 00 - b150 U 001 b160 U 001 U 00 - b171 U 00 - b180 U 00 - b190 b191 Password authentication A 0000-FFFF U 0000 - b192 Intelligent Terminal Functions C001 U 07 C022 U 00 U 07 C030 U Rated current A C031 Output [11] active state U 00 C032 Output [12] active state U 00 - C036 1.00 C052 U 1 bit U 100.0 % C053 U 02 C077 U 00 U 0.00 sec. C078 C102 C103 C104 C130 Output [11] on delay U 0.0 Sec. C131 C132 Output [12] on delay U 0.0 Sec. C133 C147 C148 Logic output 3 operand A U 00 C149 C150 C169 00 09 11 19 12 13 Page Page 00 01 02 03 04 21 22 23 24 25 40 41 42 43 44 Motor Constants Functions H001 U U 00 - H002 Motor constant selection U 00 - H202 U mH H033 U H233 U A U 0 H132 H113 H131 H133 Expansion Card Functions P parameters will be appeared when the expansion option is connected. P001 U 00 - P003 U 00 - P046 P048 U 00 - P049 p055 p056 p057 Pulse train input bias setting Set range is 100~100 % U 0. % p058 Page Monitoring Trip Events, History, & Conditions Error Codes Page 87 E81 E83 CE-EMC Installation Guidelines Important notes Page Page 91 Installation for WJ200 series (example of SF models) M (Foot-print) Hitachi EMC Recommendations 93 Functional Safety (Certification in Progress) Introduction Stop Category defined in EN60204-1 How it works Activation ONOFF ON (EDM) OFF (normal) Installation 95 Wiring example WJ200 Fuse In case of Source logic Inserting diode Switch OFF 1 Switch OFF