
* 10.20.0.0 | 255.255.255.0 | 10.20.0.243 | direct | fixed | 20 |
* 10.20.0.243 | 255.255.255.255 | 10.20.0.243 | local | addr | 20 |
* 10.20.0.255 | 255.255.255.255 | 10.20.0.255 | broadcast | broadcast | 20 |
* 10.35.0.0 | 255.255.255.0 | 10.35.0.243 | direct | fixed | 35 |
* 10.35.0.243 | 255.255.255.255 | 10.35.0.243 | local | addr | 35 |
* 10.35.0.255 | 255.255.255.255 | 10.35.0.255 | broadcast | broadcast | 35 |
* 10.36.0.0 | 255.255.255.0 | 10.36.0.243 | direct | fixed | 36 |
* 10.36.0.243 | 255.255.255.255 | 10.36.0.243 | local | addr | 36 |
* 10.36.0.255 | 255.255.255.255 | 10.36.0.255 | broadcast | broadcast | 36 |
* 10.45.0.0 | 255.255.255.0 | 10.10.0.244 | indirect | rip | 2 10 |
* 10.46.0.0 | 255.255.255.0 | 10.10.0.244 | indirect | rip | 2 10 |
* 10.99.0.0 | 255.255.255.0 | 10.36.0.246 | indirect | rip | 2 36 |
* 127.0.0.0 | 255.0.0.0 | 0.0.0.0 | martian | martian |
|
* 255.255.255.255 | 255.255.255.255 | 255.255.255.255 | broadcast | broadcast |
|
>>GbESM_1 - IP Routing# /i/l3/rip
[RIP Information Menu]
routes | - | Show | RIP | routes |
|
dump | - | Show | RIP | user's | configuration |
>>GbESM_1 - RIP Information# routes 10.10.0.0/24 via 10.20.0.244 metric 2 10.20.0.0/24 via 10.10.0.244 metric 2 10.35.0.0/24 via 10.20.0.244 metric 3 10.36.0.0/24 via 10.20.0.244 metric 3 10.45.0.0/24 via 10.10.0.244 metric 2 10.46.0.0/24 via 10.10.0.244 metric 2 10.99.0.0/24 via 10.36.0.246 metric 2
>>GbESM_1 - RIP Information# dump
Enter interface number:
RIP USER CONFIGURATION : |
|
RIP on updat 30 |
|
RIP Interface 10 : 10.10.0.243, | enabled |
version 2, listen enabled, supply enabled, default listen poison disabled, trigg enabled, mcast enabled, metric 1 auth none,key none
Cisco commands to verify RIP
The sh ip route command is the CIsco equivalent of the dump command shown above. RIP routes are marked by the letter R in the left hand column. Most OSPF commands are marked by the letter O. The show ip protocol command (shown in Example
Example 7-37 Cisco commands to verify RIP
sh ip prot
*** IP Routing is NSF aware ***
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 19 seconds
Invalid | after 180 seconds, hold down 180, flushed | after 240 | ||
Outgoing update | filter list for all interfaces is | not | set | |
Incoming update | filter list for all interfaces is | not | set | |
Redistributing: | rip |
|
| |
Default | version | control: send version 2, receive version 2 |
132Nortel Networks L2/3 Ethernet Switch Module for IBM Eserver BladeCenter